1 / 10

General Woodworking Units 2 & 3 Wood Properties

General Woodworking Units 2 & 3 Wood Properties. Mr. Nelson Darien High School. Wood Properties. Crown. Trunk. Roots. Crown: Photosynthesis occurs here (CO2 + H2O + SUN= Sugar + O2 Provides some raw materials (for wafer /particle board etc.) Trunk:

chip
Télécharger la présentation

General Woodworking Units 2 & 3 Wood Properties

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. General Woodworking Units 2 & 3 Wood Properties Mr. Nelson Darien High School

  2. Wood Properties Crown Trunk Roots • Crown: • Photosynthesis occurs here (CO2 + H2O + SUN= Sugar + O2 • Provides some raw materials (for wafer /particle board etc.) • Trunk: • Supports the crown -Provides us with lumber • Roots: • Anchor the tree -Absorb Water & Minerals • Prevent Erosion • Parts of the Trunk • Outer Bark: Protection against Fire, insects & Disease. • Inner Bark: (Called Bast or Phloem) Cells carry food (SAP) madein leaves downward. • Cambium Layer: 2 cells wide, allows the tree to increase in girth. New wood forms on inside(Xylem); New bark on outside(Phloem). • Sapwood: Newer, lighter colored, Springy growing part of the wood which carries sap from roots upward. • Heartwood: Older, less alive, darker colored part of the wood. Was sap wood. More Ridged. • Pith: soft, Center of the tree. Allows for vertical growth. Considered a defect. • Medullary Ray Cells: Channels which carry food/sap horizontally. • Annual Rings: New Ring Each Year • Springwood: Lighter colored, less dense part of each ring (Spring growth). • Summerwood: Darker colored, more dense part of each ring (Summer growth).

  3. Wood Classifications • Softwoods • Conifers: Cone or needle bearing trees • Examples: Spruce, Fir, Hemlock • Hardwoods • Deciduous: Broad leaf trees - shed leaves in winter • Examples: Oak, Birch, Beech Sawing Methods • Plain Sawing: • Most common, easiest method • Called “Flat Grained” on softwoods • Produces “U Shaped” face grain • Least expensive method • Wood warps the most

  4. Quarter Sawing: • Called edge or Vertical Grained on softwoods • Produces straight almost parallel face grain • More Expensive • More difficult, log is 1st “quartered”, then sawed tangent to rings (65-90 degree angle) • Rift Sawing: • Logs “quartered” then sawed at a 35-65 degree angle • Yields more, wider boards with pronounced rays • Most expensive • Surface Condition: • Rough lumber: straight off the saw blade • Dressed: Surfaces planed S1S, S2S or S4S • “NOMINAL SIZE”= Before Planing : “2 X 4” • “ACTUAL SIZE”= After Planing: “1 1/2” x 3 1/2”

  5. Drying / Seasoning Lumber • Moisture Content : Percentage of moisture to wood cells • Green Lumber (GR): • Can contain 30-300% moisture content • a green 2 X 4 X 8 can have up to 3 gallons of h20 • Air Dried (AD): • One month to a year. yields a 12-15% MC (in some species) • Kiln Dried (KD): • One to four weeks yields a 10% or less MC

  6. Lumber Grades • Softwoods • Best& Most Expensive Grade • Select Grade A: “Clear” • Select Grade B Few Knots • Select Grade C More Knots • Select Grade D Most Knots • 2nd Best Grade- Less Expensive • Common # 1-5 • House Trim is Common #2 • Hardwoods • Best& Most Expensive Grade • F.A.S. (Firsts & Seconds) 85-90% clear • 2nd Best, Less Expensive Grade • Select: Good for Furniture, At least 1 good face • 3rd & 4th best Grades • Common # 1 & #2 : 66% clear, narrow boards • Grading done from worst side of board • Lumber sold in “Random widths & Lengths”

  7. Purchasing Lumber • Linear or “Running” Foot • Price per foot of material • Molding, dowel • Square Foot/age • Sheet Goods: Plywood, Wafer Bd., Paneling, Particle Bd. • Calculate Area (Length X Width) • The Board Foot • How Lumber is sold • Volume measurement • 1 Board Foot = 1” X 12” X 12” • Formulas For Board Foot Calculation • “C”=100 Bd. Ft., “M”= 1000 Bd. Ft. • All Fractions get rounded UP to next inch for calculation • Must Carry out answer 2 decimal places • A) Use If LENGTH is given in INCHES T” X W” X L” 144 • B) Use If LENGTH is given in FEET T” X W” X L’ 12

  8. . 64.00 5 . 64.00 60.00 4.00 5 .3 64.00 60.00 40 36 4 5 .3 64.00 60.00 40 36 4 5 .33 64.00 60.00 40 36 4 36 4 12 12 12 12 12 Sample Board Foot Problem Example: 2” X 4” X 8’ Step 1 2 X 4 X 8 12 Step 2 8 X 8 12 Step 3 64 12 Answer= 5.33 BD. FT.

  9. . 64.00 .4 640 576 640 .44 640 576 640 576 64 144 144 144 Sample Board Foot Problem Example: 3/4” X 4” X 16’’ Step 1 1 X 4 X 16 144 Step 2 4 X 16 144 Step 3 64 144 Answer= .44 BD. FT.

  10. Putting It All Together…..A Complete Lumber Order • Should Include : • Species • Lumber Grade • Sawing Method • Amount (Board Footage) • Size Pieces (Nominal T x W x L ) • Surface Condition • (Rough/Dressed s2s, S1s, S4S) • Drying Method

More Related