1 / 26

IE 418/518: Telecommunication Concepts

IE 418/518: Telecommunication Concepts. Lecture Notes #6 Digital Data Communication Techniques. System A. System B. Transmission Modes. Timing problems require a mechanism to synchronize the transmitter and receiver Timing of bits is the key!. ……101101. Controlling Timing.

daria-murphy
Télécharger la présentation

IE 418/518: Telecommunication Concepts

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. IE 418/518:Telecommunication Concepts Lecture Notes #6 Digital Data Communication Techniques

  2. System A System B Transmission Modes • Timing problems require a mechanism to synchronize the transmitter and receiver • Timing of bits is the key! ……101101

  3. Controlling Timing • Two solutions • Asynchronous Transmission • Each character of data is treated independently • Synchronous Transmission • For sending large blocks of data • Control schemes • Character-oriented • Bit-oriented

  4. Asynchronous Transmission • Data transmitted one character at a time • 5 to 8 bits • Timing only needs to be maintained within each character • Transmitter and Receiver clocks need not be in sync! • Resynchronize at the beginning of each character

  5. Asynchronous Transmission Behavior • In a steady stream, interval between characters is uniform • Length of stop element • In idle state • Receiver looks for transition 1 to 0 • Then samples next seven intervals • Char length • Then looks for next 1 to 0 for next char

  6. Asynchronous Transmission Diagram

  7. Asynchronous Transmission Advantages • Simple • Cheap • Overhead of 2 or 3 bits per char • Approx  20% • Good for data with large gaps • e.g. keyboard

  8. Asynchronous Transmission Frame synchronization • Blocks of printable characters • Encapsulate complete block between two special (non-printable) transmission control characters • STX  Start-of-text • ETX  End-of-text

  9. Asynchronous Transmission Frame synchronization • Binary data • e.g., Contents of a file containing a compiled program • Use of single ETX not sufficient to indicate the end of a file • One of the bytes might be the same as an ETX character • Solution  STX and ETX are preceded by another transmission control character • Data link escape (DLE)

  10. Asynchronous Transmission Frame synchronization • Binary data • Character or byte stuffing

  11. Synchronous Transmission • Two approaches • Character-oriented • Bit-oriented • Both use the same bit synchronization methods • Major difference is in how they achieve character & frame synchronization

  12. Synchronous Transmission Bit Level • Block of data transmitted without start or stop bits • Tx and Rx clocks must be synchronized!!! • Option 1 -- Can use separate clock line • Good over short distances • Subject to impairments • Option 2 -- Embed clock signal in data • Manchester encoding • Carrier frequency (analog)

  13. Synchronous Transmission Character-Oriented • Used for transmission of block of characters • e.g., files of ASCII characters • Character synchronization • Achieved with synchronous idle character (SYN) • Frame synchronization • STX-ETXsequence preceded by SYN char • Once bit-synchronization is achieved • Receiver enters “hunt mode” • Bit stream is interpreted in windows of 8 bits

  14. Synchronous Transmission Character-Oriented Example

  15. Synchronous Transmission Bit-Oriented • Used for transmission of binary data • Preferred control scheme • Point-to-point links • Uses a flag pattern for start and end of frame • Idle bytes  01111111 • Flag pattern  01111110 • Bit stuffing (or zero bit insertion) • Inserts a “0” after five consecutive 1s • LANs use a similar scheme • More efficient (lower overhead) than async

  16. Synchronous Transmission Bit-Oriented Example

  17. Complementary Reading • Halsall, F., Data Communications, Computer Networks and Open Systems, (USA: Addison-Wiley, 1996), pp. 107-125.

  18. ERROR DETECTION

  19. Basic Probability Concepts • Pb Probability a bit is received in error (BER) • P1  Probability a frame arrives with no errors • P2  Probability that, with the use of error detection, a frame arrives with one or more undetected errors • P3  Probability that, with the use of error detection, a frame contains errors and these will be detected

  20. Error Detection • Additional bits added by transmitter for error detection code • Additional bits calculated as a function of the other bits • Parity • Value of parity bit is such that character has even (even parity) or odd (odd parity) number of ones • Even number of bit errors goes undetected • Requires retransmission if an error is detected

  21. Parity Example • Character to be transmitted  “S” • “S”  1010011 • Even Parity  0 1010011 • Odd Parity  11010011 • Transmission w/ one error (odd)  11011011 • Error detected!! • Transmission w/ two errors (odd)  11011111 • No error detected!! • Received character is “_”

  22. Cyclic Redundancy Check (CRC) • Useful to detect error bursts • Process Steps: • For a block of k bits (message), transmitter generates an (n – k)- bit sequence • Known as the Frame Check Sequence (FCS) • Transmit n bits which is exactly divisible by some number • Receiver divides frame by that number • If no remainder, assume no error

  23. Cyclic Redundancy Check (CRC) • T n-bit frame to be transmitted • D  k-bit block of data, or message • The first k bits of T • F  (n – k)-bit Frame Check Sequence (FCS) • The last (n - k) bits of T • P  Pattern of n – k + 1 bits • Predetermined divisor

  24. CRC Example • Calculate the FCS for the message shown below using P = 11001 • D  11100110 • FCS  ?

  25. CRC Example

  26. CRC Standards • CRC-12 • Used when character length is 6 bits • CRC-16 and CRC-CCITT • Used when character length is 8 bits • Used in WANs • CRC-32 • Used in LANs • DoD applications

More Related