1 / 33

Wireless WANs C hapter 16

Wireless WANs C hapter 16. Cellular Telephony. Designed to provide communication between two mobile (moving) units, called mobile stations (MSs), or between one mobile unit and one stationary unit, often called a land unit.

davis
Télécharger la présentation

Wireless WANs C hapter 16

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Wireless WANsChapter 16

  2. Cellular Telephony • Designed to provide communication between two mobile (moving) units, called mobile stations (MSs), or between one mobile unit and one stationary unit, often called a land unit. • Service provider must be to locate and track a caller, assign a channel to the call, and transfer the channel from BS to BS as the caller moves out of range.

  3. Cellular system Base station antenna (3 sector) 1/3rd of cell is covered by each sector of antenna

  4. How cellular telephone systems work • The area (a city, or a part of town) is divided into a number of cells (typically 1 to 12 miles in radius, but can be smaller for more crowded areas) and a base station is positioned within each cell • Adjacent cells assigned different set of frequencies to avoid interference • If a user (mobile phone/ station) is within a particular cell, the call is handled by the corresponding base station within that cell

  5. (Cont.) • As a user moves from one cell to another, the call is “handed over” to the base station of the other cell-This is called handoff • The handoffis hopefully soft (transparent) to the user instead of hard handoff.

  6. (Cont.) • the signal from a mobile unit to a base station (BS) is transmitted by radio waves at a certain frequency through the air • The signal from the mobile unit arrives at the antenna of the base station • The signal from the base station is sent to a mobile switching center (MSC) and possibly to a telephone central office through electrical wires where it is switched to the appropriate destination • MSC responsible for connecting calls, recording call information, and billing

  7. Figure 16.1 Cellular system

  8. Figure 16.2 Frequency reuse patterns

  9. Transmitting • The caller enter a phone number (7 or 10 digits) • MS scans the band seeking for a channel with strong signal • Send the data to the closest BS using that channel • BS relays data to MSC and then to telephone central office • If the called party is available, MSC assigns an unused voice channel to the call and a connection is established

  10. Receiving • When a mobile phone (MS) is called, the telephone central office sends the number to the MSC. • MSC searches for the location of the MS by sending query signals to each cell in a process “paging”. • If MS is found, MSC transmits a ring signal and assigns a voice channel to the call when MS answers.

  11. Roaming • A user can have access to communication or can be reached where there is a coverage. • Neighboring service providers can provide extended coverage through a roaming contract • Similar to snail mail between countries

  12. Generations of Cellular System First generation : • was designed for voice communication using analog signals • AMPS (Advanced Mobile Phone System): one of the leading analog cellular phone systems used in North America • Uses FDMA (frequency division multiple access) to separate channels in a link • Operates in the ISM 800-MHZ band • Uses two separate analog channels, one for forward and one for reverse communication • Uses FM (frequency modulation) to modulate voice channel and FSK (frequency shift keying) modulation to modulate control channel

  13. Figure 16.3 Cellular bands for AMPS

  14. Generations of Cellular System Second generation: • To provide high-quality (less noise-prone) voice transmission • was designed for voice communication using digital signals • Three major digital cellular phone systems: • D-AMPS (Digital AMPS): • Backward compatible with AMPS(Use same bandwidth as AMPS 800MHz) • Resue factor of 7. • GSM (Global System for Mobile Communication): • Uses two bands for duplex communication( forward , reverse) • Each uses 25 MHz band • 124 channel with 200 KHz separated by guard band • Reuse factor as low as 3 because of complex error correction

  15. Generations of Cellular System Second generation: • IS-95 (Interim Standard 95) • Uses two bands for duplex communication (Each band is 800 MHz or 1900 MHz divided into 20 channel of 1.228 MHz separated by guard band ) • Forward uses CDMA and it needs to synchronize the channel. • Reverse uses DSSS without without synchronization. • Reuse factor of 1 because the DSSS and CDMA will not allow interference.

  16. Figure 16.5 Second-generation cellular phone systems

  17. Generations of Cellular System Third generation : now being implemented Provides both digital voice and data communication (make a call, use the internet, download, video conference,… ITU (international telecommunication union) issued Internet Mobile Communication 2000 (IMT -2000) which defines some criteria for third generation: • Higher-quality voice transmission • High bandwidth and data rate • Interface the internet

  18. Generations of Cellular System Forth generation : • There are two candidate systems are commercially deployed : • Mobile WiMaxin 2006 • Long Term Evolution (LTE) in 2009 • 1800 to 2300 MHz band

  19. Figure 16.12 IMT-2000 radio interfaces

  20. Satellite Networks • Is a combination of nodes (satellites, Earth station, end-user terminal , or telephone) that provides communication from one point on the Earth to another • divides planet into cells (like cellular NW) • Provides transmission to and from any location on Earth without requiring a huge investment in ground-base infrastructure • Extensively used by TV networks.

  21. Figure 16.13 Satellite orbits

  22. Example 16.1 What is the period of the Moon, according to Kepler’s law? Here C is a constant approximately equal to 1/100. The period is in seconds and the distance in kilometers.

  23. Example 16.1 (continued) Solution The Moon is located approximately 384,000 km above the Earth. The radius of the Earth is 6378 km. Applying the formula, we get.

  24. Example 16.2 According to Kepler’s law, what is the period of a satellite that is located at an orbit approximately 35,786 km above the Earth? Solution Applying the formula, we get

  25. Example 16.2 (continued) This means that a satellite located at 35,786 km has a period of 24 h, which is the same as the rotation period of the Earth. A satellite like this is said to be stationary to the Earth. The orbit, as we will see, is called a geosynchronous orbit.

  26. Figure 16.14 Satellite categories Geostationary Earth Orbit Low Earth Orbit Middle Earth Orbit

  27. Figure 16.15 Satellite orbit altitudes

  28. Table 16.1 Satellite frequency bands

  29. Figure 16.16 Satellites in geostationary orbit

  30. Figure 16.17 Orbits for global positioning system (GPS) satellites

  31. Figure 16.19 LEO satellite system

  32. Figure 16.20 Iridium constellation

  33. Iridium system • The Iridium system has 66 satellites in six LEO orbits, each at an altitude of 750 km. • Iridium is designed to provide direct worldwide voice and data communication using handheld terminals, a service similar to cellular telephony but on a global scale.

More Related