1 / 8

40G QSFP Modules Installation Guide

A good practice and correct installation are very important for 40G network system, not only to protect the 40G transceiver optics and device from damage, but also to ensure a stable performance for system.

followkern
Télécharger la présentation

40G QSFP Modules Installation Guide

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. WHITE PAPER 40G QSFP+ Modules Installation Guide Table Of Contents 40GbE QSFP+ Transceivers Overview 40GBASE-SR4 QSFP+ Module 40GBASE-LR4 QSFP+ Module How to Install/Remove QSFP+ Transceivers and DAC/AOC Cables Preparations To Install or Remove a QSFP+ Transceiver Module To Install a QSFP+ Transceiver Module To Remove a QSFP+ Transceiver Module To Install or Remove a 40G QSFP+ Cable To Install a QSFP+ DAC Cable To remove a QSFP+ DAC Cable To Install or Remove a 40G QSFP+ to 4x10G SFP+ Cable To Install an SFP+ Transceiver Module To Remove an SFP+ Transceiver Module Verifying the installation Conclusion 1 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  2. WHITE PAPER To install and remove the transceiver optics in a right way is very necessary to ensure the network to work stably and efficiently. Today, we are going to introduce an installation guide of QSFP transceivers and DAC/AOC cables in 40G network. 40GbE QSFP+ Transceivers Overview 40 Gigabit Ethernet (40GbE) aggregation switches are becoming more common in today's data centers. At the heart of the 40GbE network layer is a pair of transceivers connected by a cable. The transceivers are plugged into either network servers or a variety of components including interface cards and switches and connected via the cables such as OM3 and OM4 for multimode application. Additionally DAC (Direct Attach Copper) cables or AOCs (Active Optical Cables) are used for short interconnection as a more cost-effective alternative solution. QSFP+ (Quad Small Form-factor Pluggable Plus) is the most common 40GbE interface type, and also as a high-density 10GbE interface via QSFP+ breakout cables. QSFP+ interfaces a network device (switch, router, media converter or similar device) to a fiber optic or copper cable, supporting data rates from 4x10 Gbps and supports Ethernet, Fibre Channel, InfiniBand and SONET/SDH standards with different data rate options. Compared to CFP (C form-factor pluggable) transceiver modules, QSFP transceiver modules are more compact and more suitable for port-density application. The two basic interface specifications of QSFP+ modules respectively for multimode and single-mode applications are 40GBASE-SR4 and 40GBASE-LR4.  40GBASE-SR4 QSFP+ Module The 40GBASE-SR4 QSFP+ module, conforming to the 802.3ba D3.2 (40GBASE-SR4) standard, provides a 40Gbps optical connection using MPO/MTP® optical connectors. This optical module integrates four data lanes in each direction with 40Gbps aggregate bandwidth and each lane can operate at 10.3125 Gbps. It is used in data centers to interconnect two Ethernet switches with 8 fiber parallel multimode fiber OM3/OM4 cables (transmission distance can be up to 100 meters using OM3 fiber or up to 150 meters using OM4 fiber). 2 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  3. WHITE PAPER  40GBASE-LR4 QSFP+ Module The 40GBASE-LR4 QSFP+ module, conforming to the 802.3ba (40GBASE-LR4) standard, provides a 40Gbps optical connection using LC optical connectors. This optical module integrates four data lanes in each direction with 40Gbps aggregate bandwidth and each lane can operate at 10.3125 Gbps. It is most commonly deployed between data center or IXP sites with single-mode fiber up to 10 km. In addition, to satisfy a number of different objectives including support for MMF and SMF compatibility, there are other types of QSFP+ modules offered by different vendors. How to Install/Remove QSFP+ Transceivers and DAC/AOC Cables Preparations To protect a QSFP+ module or cable from ESD (electro-static discharge) damage, before installing or removing a QSFP+ module or cable, be remembered that always wear an ESD wrist strap and make sure that it makes good skin contact and is securely grounded (If you are using ESD gloves, wear the wrist strap outside the ESD glove). To Install or Remove a QSFP+ Transceiver Module There are two types of clasp designed for a QSFP+ transceiver module—plastic clasp or a metallic clasp. Here uses the metallic clasp type as an example.  To Install a QSFP+ Transceiver Module Step 1. Remove the QSFP+ module from its antistatic container and remove the dust covers from the module optical connector. Step 2. Remove any rubber dust covers from the port where you are installing the QSFP+ module. Step 3. Pivot the clasp of the module up. (Skip this step if the clasp is plastic.) Step 4. Align the module with the port in the chassis, as shown in Figure 1. 3 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  4. WHITE PAPER Figure 1. Aligning the module with the port Step 5. Holding the module, gently push in the module until it is firmly seated in the port. (see Figure 2.) Figure 2. Install the QSFP+ module to port Step 6. Immediately attach the patch cord with MPO connector or duplex LC connector to the QSFP+ transceiver module. (see Figure 3.) Figure 3. Install the patch cord to the module Note: Install the dust plug for the transceiver module if you are not to install an optical fiber into it.  To Remove a QSFP+ Transceiver Module Step 1. Remove the optical fiber if any. 4 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  5. WHITE PAPER Step 2. Pivot the clasp of the module down to the horizontal position. (Skip this step if the clasp is plastic.) Step 3. Holding the module, gently pull the module out of the port. (Figure 4) Step 4. Place the QSFP+ transceiver into an antistatic bag. Figure 4. Remove the QSFP+ module To Install or Remove a 40G QSFP+ Cable The installation and removal procedures are the same for QSFP+ DAC cables and QSFP+ AOC cables. Here uses a QSFP+ DAC cable as an example:  To Install a QSFP+ DAC Cable Step 1. Align the QSFP+ transceiver module (with the clasp on top) at one end of the cable with the port in the chassis, as shown in Figure 5. Step 2. Horizontally and gently push in the module to fully seat it in the port. Figure 5. Installing a QSFP+ DAC cable  To remove a QSFP+ DAC Cable Step 1. Gently press and release the QSFP+ transceiver module.(see Figure 6.) Step 2. Holding the cable, gently pull the clasp on the cable to pull out the transceiver module. 5 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  6. WHITE PAPER Figure 6. Removing a QSFP+ DAC cable To Install or Remove a 40G QSFP+ to 4x10G SFP+ Cable 40G QSFP+ to 4x10G SFP+ cable combines one 40G QSFP+ module on one end and four 10G SFP+ module on the other end. The installation and removal procedures of 40G QSFP+ connector are introdueced above. Here only introduced the installation and removal of 10G SFP+ module:  To Install an SFP+ Transceiver Module Step 1. Align the module with the SFP+ port, with the golden plating facing the spring tab (see Figure 7.) in the SFP+ port. If the chassis has two rows of ports, the spring tab in a port is on the bottom in the upper row and on the top in the lower row. Step 2. Slightly press the module against the spring tab so you can push the module straight into the port. Figure 7. Installing an SFP+ transceiver module  To Remove an SFP+ Transceiver Module Step 1. Press the module with your thumb, as shown by callout 1 in Figure 8. Step 2. Gently pull the clasp on the cable to pull out the transceiver module, as shown by callout 2 in Figure 8. 6 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  7. WHITE PAPER Figure 8. Removing an SFP+ transceiver module Verifying the installation Execute the display transceiver interface command on the device to verify that the transceiver module or DAC/AOC cable is installed correctly. If the transceiver module and DAC/AOC cable information is displayed correctly, the installation is correct. If an error message is displayed, the installation is incorrect or the transceiver optics is not compatible. Conclusion As 40 GbE are widely deployed, 40G transceiver optics are ubiquitous. A good practice and correct installation are very important for 40G network system, not only to protect the 40G transceiver optics and device from damage, but also to ensure a stable performance for system. In addition, by executing the display transceiver interface command, we can verify whether the installation is correct. Of course, the premise is that the transceiver optics you use is fully compatible with your device. Fiberstore offers a comprehensive line of high-compatible 40G transceiver optics, such as 40GBASE-SR4 QSFP+, 40GBASE-LR4 QSFP+ and 40G DACs and AOCs with competitive prices. Each of them is tested in original-brand switch which ensures the 100% compatibility to your device. For more information or quotation, please contact us via sales@fs.com. 7 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

  8. WHITE PAPER Contact Us Follow us Manufacturing R & D (China) North America (United States) Eastern Side, Second Floor, Science & Technology Park, No.6, Keyuan Road, Nanshan District, Shenzhen 518057, China Tel: +86 (755) 8300 3611 Fax: +86 (755) 8326 9395 Email: sales@fs.com 331 Andover Park East Ste330, Tukwila, WA 98188,United States Tel: +1-425-226-2035 Fax: +1-253-246-7881 Email: sales@fs.com LinkedIn Twitter Facebook G+ APAC Office (Hong Kong) London Office (United Kingdom) Pinterest 1220 Tung Chun Commercial Centre, 438-444 Shanghai Street, Kowloon, Hong Kong Tel: +852 81763606 Fax: +852 81763606 Email: sales@fs.com Third Floor 207 Regent Street, London, W1B 3HH, United Kingdom Tel: +44 2081441980 Youtube Blog Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment features, or service offered or to be offered by Fiberstore. Fiberstore reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This information document describes features that may not be currently available. Contact a Fiberstore sales team for information on feature and product availability. 8 Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide Fiberstore (FS.COM) | 40G QSFP+ Modules Installation Guide

More Related