1 / 16

Al - Kapton Bus development at RIKEN

Al - Kapton Bus development at RIKEN. Process Sticking Al – Kapton Etching Through hole Stacking Gold plating Issues Plan. Atsushi Taketani (taketani@riken.jp). ALICE Full Al BUS. 5 to 7 m m Al. 12 m m Polyimide. 5 to 7 m m Al. 5 m m glue. 12 m m Polyimide. 5 m m glue.

freya
Télécharger la présentation

Al - Kapton Bus development at RIKEN

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Al - Kapton Bus developmentat RIKEN • Process • Sticking Al – Kapton • Etching • Through hole • Stacking • Gold plating • Issues • Plan Atsushi Taketani (taketani@riken.jp) 2004-11-15 ALICE ITS

  2. ALICE Full Al BUS 5 to 7 mm Al 12 mm Polyimide 5 to 7 mm Al 5 mm glue 12 mm Polyimide 5 mm glue 15 mm Al 5 mm glue 12 mm Polyimide 5 mm glue 50 mm Al 5 mm glue 12 mm Polyimide 5 mm glue 50 mm Al 5 mm glue 12 mm Polyimide Glue 35 mm 0.0122% X0 Al 125 -130 mm 0.140% X0 Polyimide 60 mm 0.0210% X0 Total radiation length = 0.173 % X0 2004-11-15 ALICE ITS

  3. Aluminum Aluminum Polyimide Polyimide Polyimide Manufacture Process 4 Through hole 1 Glued 5 Alignment and Etching 2 Etching 3 Glued 6 Gold plating 2004-11-15 ALICE ITS

  4. 8 micron m Polyimide (Ink) 12 micron m Al Sticking Al - Kapton Press with heat No glue! 2004-11-15 ALICE ITS

  5. Etching ALICE BUS Vertical ALICE BUS Horizontal I bring most of the samples which I show in slides. Trying 30 micron line width! 2004-11-15 ALICE ITS

  6. Our Trial pattern 12 micron Al 8 micron Kapton Single layer 80 micron space 80 micron width 2004-11-15 ALICE ITS

  7. Bad etching sample Fatal case Dimple along the line We expect to avoid these problem by washing with NaOH before photo resist painting. 2004-11-15 ALICE ITS

  8. 8 micron m Polyimide (Ink) 8 micron m Polyimide (Ink) 12 micron m Al 12 micron m Al Sticking next layer No glue! Press with heat Not Etched Etched 2004-11-15 ALICE ITS

  9. Through Hole (Laser drilling) 2004-11-15 ALICE ITS

  10. Through Hole (Cross section) 0.5mm 2004-11-15 ALICE ITS

  11. 8 micron m Polyimide (Ink) 8 micron m Polyimide (Ink) 12 micron m Al 12 micron m Al Stacking layer Project line patterns with alignment (Common technique for Cu board) Photo resist Not Etched Etched 2004-11-15 ALICE ITS

  12. Top 2nd 3rd 3 signal layers + Power/GND layers 2004-11-15 ALICE ITS

  13. Gold Plating • We already made a Al -Ni-Au plated sample. • It worked for Al wire boding. 2004-11-15 ALICE ITS

  14. Issue We do not have an idea how to make these steps 50 mm Al 50 mm Al 2004-11-15 ALICE ITS

  15. Possible Solution Additional through hole and bonding pad 50 mm Al 50 mm Al 2004-11-15 ALICE ITS

  16. Plan • We almost establish essential techniques which we need. • I am requesting a board including all essential techniques( etching, through hole, stacking with alignment, gold-plating) • It will come end of Dec. 2004. • After we confirm them, we start to design PHENIX board in Jan. 2004 and fabricate until Mar. 2005.(fastest guess) 2004-11-15 ALICE ITS

More Related