1 / 43

Communication lines

Communication lines. OSI model. Open Systems Interconnection (OSI) model (ISO/IEC 7498-1). Physical layer – specifies electrical and physical properties (cable) Pins, voltages, impedance, modulation, timing, topology. Source: homepages.uel.ac.uk . OSI model.

galen
Télécharger la présentation

Communication lines

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Communication lines

  2. OSI model • Open Systems Interconnection (OSI) model (ISO/IEC 7498-1) • Physical layer – specifies electrical and physical properties (cable) • Pins, voltages, impedance, modulation, timing, topology Source: homepages.uel.ac.uk

  3. OSI model • Open Systems Interconnection (OSI) model (ISO/IEC 7498-1) • Physical layer – Transmits raw bit stream over physical cable • IEEE 802, RS232, RS422, RS485, I2C, SPI,… Source: homepages.uel.ac.uk

  4. OSI model • Open Systems Interconnection (OSI) model (ISO/IEC 7498-1) • Data link layer – specifies network data frame (packet), checksum, source and destination address, and data • E.g. Ethernet MAC, RS232 Source: homepages.uel.ac.uk

  5. OSI model • Open Systems Interconnection (OSI) model (ISO/IEC 7498-1) • Network layer – routing, directing datagrams from one network to another • E.g. IP addresses Source: homepages.uel.ac.uk

  6. RS232 (EIA232) • Dates from 1969 (RS-232-C) • Last standard is TIA/EIA-232-F from 1997 • Defines physical and data link layer • Single transmitter and receiver RX TX Log. 0 : > +3 V Log. 1 : < -3 V Log. 0 : +5 to +15 V Log. 1 : -15 to -5 V Noise immunity: min. 2 V

  7. RS232 (EIA232) RX TX • Length RS-232-C = 15 m • RS-232-F defines max. load capacity 2500 pF signal CRX CS CM CS ~20 pF shield

  8. RS232 - Cable capacity signal CRX CS CS ~ 0,5 CM unshielded cable CS ~ 2 CM shielded cable CM CS ~20 pF shield Max. length: Lmax = 2500 / Ctotal Ctotal = CM + CS e.g. Belden 1700A TP: 78,7 Ω/km, 45,9 pF/m

  9. RS232 - Communication protocol Log. 0 : +5 to +15 V Log. 1 : -15 to -5 V data: 11010101b (213dec) idle • Odd • Even start (parity) 0 0 0 0 1 1 1 1 1 1 stop b0 idle b2 b4 b6 b1 1,1.5,2 b3 b5 b7 LSB MSB

  10. RS232 - Asynchronous communication Fixed comm. speed: tx + rx same (tolerance ~3%) idle RX TX start (parity) 0 0 0 0 1 1 1 1 1 1 stop b0 idle b2 b4 b6 b1 b3 b5 b7

  11. RS232 - Communication speed RS-232-F limits to 30 V/µs, max 4% of bit time => max. theoretical speed 200 kbit/s 0 ΔV 1 1 Δt

  12. RS232 - Communication speed RS-232-F standard definesspeeds: 50,75,110,150,300,600,1200,2400,4800,9600,19200 bit/s Common speeds above standard definition: 28800, 38400, 57600, 115200 bit/s Higher speed = lower distance source: www.hw.cz

  13. RS232 - Signals RxD TxD Dev. 1 Dev. 2 RxD TxD RTS CTS Request to send RTS CTS Clear to send Data Carrier Detect DTR Data terminal ready DCD DSR Data Set Ready DCD DSR DTR GND

  14. RS232 - Connectors source: www.arcelect.com 9 pin

  15. RS232 - Connectors 25 pin source: fjkraan.home.xs4all.nl source: www.solentcables.co.uk

  16. RS232 - Summary • 1 transmitter, 1 receiver • Common ground • Typically 8 bit, no parity, 1 stop bit (8N1)

  17. RS-422 (EIA-422) • ANSI/TIA/EIA-422-B or ITU-T Recommendation T-REC-V.11 • Uses differential signaling + GND • 1 transmitter + 10 receivers • 10 Mbit/s (12 m), 100 kbit/s (1200 m) • Max. 1200 m • Standard does not define protocol and pins

  18. Differential signaling source: www.root.cz source: www.root.cz

  19. RS-422 Log. 0: VA – VB ≥ +0.2 V Log. 1: VA – VB ≤ -0.2 V source: www.scantec.de source: meteosat.pessac.free.fr

  20. RS-485 • ANSI/TIA/EIA-485 (1998) • Uses differential signaling • 32 transmitter + 32 receivers • 10 Mbit/s (12 m), 100 kbit/s (1200 m) • Max. 1200 m • Standard does not define protocol and pins

  21. RS-485 signaling Log. 0: VA – VB ≥ +0.2 V Log. 1: VA – VB ≤ -0.2 V Source: www.consultants-online.co.za source: www.sealevel.com

  22. RS-485 devices Internally each node can have a transmitter and receiver, they are switched into high-impedance mode when not used Source: www.root.cz

  23. Half duplex source: www.alciro.org

  24. full duplex source: www.alciro.org

  25. Grounding source: hw.cz

  26. Maximal speed source: hw.cz

  27. RS-422 vs. RS-485 source: hw.cz

  28. USB • Universal serial bus (1995) • Differential signaling (DATA + , DATA -) + power source: www.se7ensins.com source: en.wikipedia.org

  29. USB specifications • Max. 127 devices • Superspeed – 5 Gbit/s (USB 3.0 - 2008) • High Speed - 480Mbits/s (USB 2.0 - 1999) • Full Speed - 12Mbits/s • Low Speed - 1.5Mbits/s

  30. USB signaling • Uses NRZI (Non Return to Zero Invert) signaling D+ device host D- • Differential „1“: D+ > 2.8 V, D- < 0.3V • Differential „0“: D-> 2.8 V, D+ < 0.3V • Differential „1“: D+ greaterthanD- • Differential „0“: D+ lessthanD-

  31. USB signaling source: www.tek.com

  32. Speed identification • Full speed device source: www.beyondlogic.org

  33. Speed identification • Full speed device source: www.beyondlogic.org

  34. Non Return to Zero Invertsignaling • "One" is represented by a transition of the physical level. • "Zero" has no transition. source: www.jbmelectronics.com source: en.wikipedia.org

  35. Ethernet – physicallayer • Standard IEEE 802.3 • Max. length 100m • 3 Mbit/s to 100 Gbit/s • Differential signaling • Signals TX+, TX-, RX+, RX- source: techpubs.sgi.com

  36. Ethernet – physicallayer Logic levels (10BaseT - output) • Log. 1 > +0.7 V • Log. 0< -0.7 V source: hw-server.com source: www.interfacebus.com source: sigalrm.blogspot.com

  37. Ethernet – Manchester encoding • Encoding helps clock recovery source: en.wikipedia.org

  38. Ethernet – physicallayer Ethernet data, showing MLT-3 encoding of bits. (used in e.g. 100BASE-TX) source: flickr.com

  39. Ethernet – Data Link Layer - frame synchronization source: communities.netapp.com

  40. Ethernet – Data Link Layer - frame addresses source: communities.netapp.com

  41. Ethernet – Data Link Layer - frame identifies what higher-level network protocol is being carried in the frame (example: TCP/IP) source: communities.netapp.com

  42. Ethernet – Data Link Layer - frame data source: communities.netapp.com

  43. Ethernet – Data Link Layer - frame Control checksum Cyclic redundancy check source: communities.netapp.com

More Related