1 / 18

SNS Power Supply Control

SNS Power Supply Control. Sheng Peng. Overview. Power supplies are from different vendors IE power, Danfysik, Alpha … Power supplies have different capability +/- 20 Amps, +/- 35 Volts stackable +525 Amps, +35 Volts +400 Amps, +20 Volts +375 Amps, +80 Volts +390 Amps, +24 Volts

galvin
Télécharger la présentation

SNS Power Supply Control

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. SNS Power Supply Control Sheng Peng

  2. Overview • Power supplies are from different vendors • IE power, Danfysik, Alpha … • Power supplies have different capability • +/- 20 Amps, +/- 35 Volts stackable • +525 Amps, +35 Volts • +400 Amps, +20 Volts • +375 Amps, +80 Volts • +390 Amps, +24 Volts • +700 Amps, +18 Volts • +900 Amps, +51 Volts • +1300 Amps, +95 Volts • +1405 Amps, +390 Volts • +4000 Amps, +18 Volts • +6000 Amps, +440 Volts • +185 Amps, +27 Volts • +1400 Amps, +800 Volts • +2200 Amps, +33000 Volts • +20 Amps, +75 Volts • +40 Amps, +75 Volts • … • Uniform control interface for most of power supplies • SNS Power Supply Controller (PSC)/Power Supply Interface (PSI) • EPICS based software

  3. Revisons • PSC • 6U single wide VME board for operation • 1U rack mounted for PSI test and calibration • PSC based function generator (RHIC only) • PSI • 1U rack mounted for rack mounted/standalone power supply • 6U single wide VME board for VME-style power supply • “Higher speed less ADC” PSI (Under development in RHIC)

  4. Power Supplies in SNS

  5. Automated Power Supply Test and Calibration

  6. PSC/PSI Software

  7. PSI and VME with CPU and PSC PSI PSC CPU PSC/PSI Hardware

  8. PSI

  9. PSC/PSI in SNS • PSC/PSI is the SNS standard interface to every power supply • PSI (Power Supply Interface) • Installed with every power supply • One 16-bit DAC with jumper selectable Unipolar/Bipolar mode • Four 16-bit ADCs • Self calibration • 15 bits digital out with selectable static or 100ms pulse mode • 16 bits digital in • Fiber link to PSC, 9-pin analog connector/37 pin digital connector to power supply • PSC (Power Supply Controller) • Customized VME board with serial port available • Fiber link to PSI • Support 6 power supplies per board • 128K circular buffer per channel to save 5458 samples • Software or hardware triggered read/write up to 5KHz • Burst read up to 10K samples/second (BNL is upgrading it to 100K)

  10. Communication Protocol/Real-time performance • CPU  PSC • Communicate thru VME bus backplane • All registers are memory mapped • Large circular buffer holds read back • Typical VME access cycle is 0.5~1.0 µs/word • PSC  PSI • Multimode fiber with SC connector • 5MHz carrier, upgradeable to 50MHz • Each frame consist of 1 start bit, 1 byte frame ID, 3 bytes data, 1 byte CRC and 2 stop bits. So 43bits(8.6µs)/Frame in total. • Setpoint/command needs only 1 frame (plus 1 echo) • Readback needs 7 frames (1 request, 6 response) • Whole write action takes ~20µs (include DAC setup time) • Whole read action takes ~80µs

  11. Portable Power Supply Test Stand

  12. Long Term Reliability Test Stand Each VME Has 4 PSC’s Each Rack Has 24 PSI’s Running at up to 4000Hz for several months Many 10^12 messages without CRC or timeout errors.

  13. Electrical performance (Some test results) • Fiber interface provides the best electrical isolation • ADC Reading Accuracy

  14. Some Test Results • ADC Linearity Test • Approximately 1-bit (300uvolts) variation from –10v to +10v input.

  15. Some Test Results • ADC Temperature Stability 300uvolts = 1 bit Approximately ½ bit change with 10 degree F change in temp.

  16. Cost • There are two choice to get PSC/PSI • Buy as COTS from Apogee Labs • Get design then have a manufacturer to build it • PSI • RHIC built it recently with a small amount: $895 each • RHIC built revised PSC with a small amount: $1600 each • Apogee Labs ask for $2854.50 (~$2000 for BNL) per board with the order more than 100 boards • Assume we buy PSC from Apogee Labs and build PSI like RHIC did, the cost will be $895 + $2854.50/6 = ~$1380/PS • If we build PSC too, the target cost should be ~$1150/PS

  17. Status • In use at NSRL and SNS • DC power supplies 100ppm accuracy • 60Hz triggered read/write • Preliminary use at IHEP • planned for BEPC-II • Under evaluation for other BNL applications • Design owned by BNL • EPICS S/W freely available

  18. Summary • PSC/PSI combination can be a cost-effective solution • H/W is proven reliable • H/W design is “open” • EPICS S/W is available • User community is growing

More Related