1 / 54

FUNDAMENTAL OF ELECTRICAL ENGINEERING EMT 113/4

Fundamental of Electrical Engineering. FUNDAMENTAL OF ELECTRICAL ENGINEERING EMT 113/4. Semester II 09/10. CHAPTER 3: AC MACHINES. Fundamental of Electrical Engineering. Introduction. 2 major classes: a) Asynchronous machines / induction machines :–

hall-lee
Télécharger la présentation

FUNDAMENTAL OF ELECTRICAL ENGINEERING EMT 113/4

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Fundamental of Electrical Engineering FUNDAMENTAL OF ELECTRICAL ENGINEERINGEMT 113/4 Semester II 09/10 CHAPTER 3: AC MACHINES

  2. Fundamental of Electrical Engineering Introduction 2 major classes: a) Asynchronous machines / induction machines :– Motors or generators whosefield current is supplied by magnetic induction (transformer action) into their field windings. b) Synchronous machines :– Motors or generators whose field current is supplied by a separate dc power source. Note: 1) Induction motor has the samephysical stator as a synchronous machine, with a different rotor construction. 2) The fields circuit of most synchronous and induction machines are located on their rotors. Semester II 09/10 Motors = ac electrical energy  mechanical energy Generators = mechanical energy  ac electrical energy

  3. V eind Fundamental of Electrical Engineering AC Machinery Fundamental A SIMPLE LOOP IN A UNIFORM MAGNETIC FIELDS. • A rotating loop of wire within the magnetic field. • Magnetic field produced by a large stationary magnet produce-constant and uniform magnetic field, B. • Rotation of the loop induced a voltage in the wire. • Current flows in the loop, a torque will be induced on the wire loop. Semester II 09/10

  4. Fundamental of Electrical Engineering THE ROTATING MAGNETIC FIELD • When two magnetic fields are present in a machine, a torque will be created which will tend to line up the two magnetic fields. • Magnetic field is produced by the stator and rotor of an ac machine. • Then a torque will be induced in the rotor cause the rotor to turn and align itself with the stator magnetic field. • The induced torque in the rotor would cause the rotor to constantly “ chase “ the stator magnetic field around in circle - the basic principle of all ac motor operation. Semester II 09/10

  5. Fundamental of Electrical Engineering AC MACHINE POWER LOSSES • The efficiency of an AC machines is defined as: • Four types of losses in AC machines: • Electrical or copper losses (I2R losses) • Core losses • Mechanical losses • Stray load losses Semester II 09/10

  6. Fundamental of Electrical Engineering VOLTAGE REGULATION AND SPEED REGULATION VR is a measure of the ability of a generatorto keep a constant voltage at its terminals as load varies. It is defined as follow: Semester II 09/10 SR is a measure of the ability of a motor to keep a constant shaft speed as load varies.

  7. Fundamental of Electrical Engineering INDUCTION MOTORS Semester II 09/10

  8. Fundamental of Electrical Engineering Induction Motors Induction motors are the motor frequently encountered in industry. It simple, rugged, low-priced and easy to maintain. It run essentially constant speed from zero to full-load. The speed is frequency-dependent and consequently these motors are not easily adapted to speed control Induction machines is called induction because the rotor voltage (which produces the rotor current and the rotor magnetic field) is induced in the rotor winding rather than physically connected by wires. Semester II 09/10

  9. Fundamental of Electrical Engineering Induction Motor : Construction • A 3-phase induction motor has two main parts : • A stationary stator (stationary part of the machine) • Revolving rotor (rotating part of the machine) • The rotor is separated from the stator by a small air gap (the tolerances is depending on the power of the motor). Semester II 09/10

  10. Fundamental of Electrical Engineering Two types of rotor which can placed inside the stator: a) Squirrel-cage induction motor(Cage rotor) Semester II 09/10 b) Wound rotor induction motor

  11. Fundamental of Electrical Engineering a) Squirrel cage – the conductors would look like one of the exercise wheels that squirrel or hamsters run on. Semester II 09/10 • Cage Induction Motor rotor consists of a series of conducting bars laid into slot carved in the face of rotor and shorted at either end by large shorting ring

  12. Fundamental of Electrical Engineering Semester II 09/10 Small cage rotor induction motor Large cage rotor induction motor

  13. Fundamental of Electrical Engineering • b) Wound rotor – have a brushes and slip ring at the end of rotor Semester II 09/10

  14. Fundamental of Electrical Engineering • Wound rotor has a complete set of three-phase winding that are mirror images of the winding on the stator. • - The three phases of the rotor windings are usually Y-connected, the end of the three rotor wires are tied to slip ring on the rotor shaft. • - Rotor windings are shorted through brushes riding on the slip rings. • Wound-rotor induction motors are more expansive than the cage induction motors, they required much more maintenance because the wear associated with their brushes and slip rings. Semester II 09/10

  15. Fundamental of Electrical Engineering Induction Motor : Concepts INDUCED TORQUE IN AN INDUCTION MOTOR The three-phase of voltages has been applied to the stator, and three-phase set of stator current is flowing . These currents produce a magnetic field BS , rotating counterclockwise direction Semester II 09/10 The speed of the magnetic field’s rotation in a cage rotor induction motor (Figure 7.6, Chapman) is given by Where nsync = synchronous speed [r/min] fe = System frequency [Hz] p = number of poles This equation shows that the synchronous speed increases with frequency and decrease with the number of poles. .

  16. Fundamental of Electrical Engineering This rotating field BSpasses over the rotor bars and induces a voltage in them Where : v = velocity of the bar relative to the magnetic field B = magnetic flux density vector l = length of conductorin the magnetic field Semester II 09/10 It is a relative motion of the rotor compared to the stator magnetic field that produces induced voltage in a rotor bar. The rotor current flow produces a rotor magnetic field, BR. The induce torque in the machine is given by; The voltage induced in a rotor bar depends on the speed of the rotor relative to the magnetic fields So, resulting torque is counterclockwise.

  17. Fundamental of Electrical Engineering THE CONCEPT OF ROTOR SLIP Slip speed is defined as the differences between synchronous speed and rotor speed: Where nslip = slip speed of the machines nsync = speed of the magnetic field nm = mechanical shaft speed of motor Semester II 09/10 The other term used to describe the relative motion is slip, which is relative speed expressed on a per unit or a percentage basis. The slip is defined as :

  18. Fundamental of Electrical Engineering The previous equation also can be expressed in term of angular velocity  (radians per second) as : If the rotor turns at synchronous speed, s=0 ; if the rotor is stationary (locked or stop) , s=1. All normal motor speeds fall somewhere between those limits. As for mechanical speed Semester II 09/10 These equation are useful in the derivation of induction motor torque and power relationship.

  19. Fundamental of Electrical Engineering THE ELECTRICAL FREQUENCY ON THE ROTOR. • The induction motor works by inducing voltages and current in the rotor of the machine-called a rotating transformer. • Like a transformer; primary (stator) induced a voltage in the secondary (rotor) • Unlike a transformer, the secondary frequency not necessarily the same as primary. • If the rotor of a motor islocked so that it cannot move, the rotor will have the same frequency as the stator. • If the rotor turns at synchronous speed, the frequency on the rotor will be zero. • For nm=0 r/min & the rotor frequency fr=fe slip, s = 1 nm=nsync & the rotor frequency fr=0 slip, s = 0 - For any speed in between, the rotor frequency is directly proportional to the difference between the speed of the magnetic field nsync and the speed of the rotor nm. Semester II 09/10

  20. Fundamental of Electrical Engineering THE ELECTRICAL FREQUENCY ON THE ROTOR Since the slip of the rotor is defined as : Then the rotor frequency can be expressed as : Substituting between these two equation become : Semester II 09/10 But nsync = 120fe/P, so Therefore, fr = frequency rotor; fe = frequency stator

  21. Fundamental of Electrical Engineering Induction Motor : Equivalent Circuit • Transformer model • - model of the transformer action-induction of voltages and currents in the rotor circuit of an IM is essentially a transformer operation. • - as in transformer model – certain resistance, self inductance in primary (stator) windings; magnetization curve and etc. • b)Rotor circuit model • The greater the relative motion between the rotor and the stator magnetic fields, the greater the resulting rotor voltage and frequency. • Locked-rotor or blocked-rotor –the largest relative motion when the rotor is stationary. • c) Final Equivalent circuit • - Refer the rotor part of the model over the stator side. Semester II 09/10

  22. Fundamental of Electrical Engineering A) TRANSFORMER MODEL Semester II 09/10 STATOR IDEAL TRANSFORMER ROTOR

  23. Fundamental of Electrical Engineering • Induction motor operates on the induction of voltage and current in its rotor circuit from the stator circuit (transformer action). • An induction motor is called a singly excited machine, since power is supply to only the stator circuit. • The flux in the machine is related to the integral of the applied voltage E1. • The curve of magnetomotive force versus flux (magnetization curve) for this machine is compared to a similar curve for a power transformer. Semester II 09/10

  24. Suppose the motor run at a slip s, meaning that the rotor speed is ns (1-s), where ns is the synchronous speed, then this modify the values of VOLTAGE and CURRENT on the primary and secondary side. The frequency of the induced voltage at any slip will be given fr = sfe Assuming ER0 is the magnitude of the induced rotor voltage at LOCKED ROTOR condition the actual voltage induced because of slip (s) is, ER = sER0 The resistor is not frequency sensitive, the value of RR remain the same. The rotor inductance is frequency sensitive (X=L=2fL) then XR = sXR0 Figure 6 shows the equivalent circuit when motor is running at a slip (s). Fundamental of Electrical Engineering B) ROTOR CIRCUIT MODEL Semester II 09/10

  25. Fundamental of Electrical Engineering Semester II 09/10 Equivalent circuit of a wound-rotor when it at locked or blocked condition The frequency of the voltages and currents in the stator is f, but the frequency of the voltages and currents in the rotor is sf.

  26. jXR=jsXR0 ER = sER0 RR ZReq Fundamental of Electrical Engineering Then, resulting rotor equivalent circuit as below. The rotor current flow can be found as : Semester II 09/10 The rotor circuit model of an induction motor

  27. jsXR0 ER0 The rotor circuit model with all the frequency (slip) effects concentrated in resistor RR Fundamental of Electrical Engineering Then the rotor equivalent circuit become: Semester II 09/10 ZReq

  28. Fundamental of Electrical Engineering C) FINAL EQUIVALENT CIRCUIT Remember, in transformer, the voltages, currents and impedances on the secondary side of the device can be referred to PRIMARY side by turn ratio of the transformer : Semester II 09/10 The same transformation can be used for the induction motor’s rotor circuit by using effective turn ratio aeff

  29. Fundamental of Electrical Engineering The rotor circuit model that will be referred to the stator side as shown below Semester II 09/10 The per-phase equivalent circuit of an induction motor.

  30. Fundamental of Electrical Engineering Input is 3 phase system of voltages and currents. Output is mechanical. Semester II 09/10 The power flow diagram of an induction motor – shows the relationship between the input electric power and output mechanical power.

  31. Fundamental of Electrical Engineering Induction Motor :Power & Torque Semester II 09/10 The per-phase equivalent circuit of an induction motor Where Input current

  32. Fundamental of Electrical Engineering Induction Motor : Torque Speed Characteristics Semester II 09/10

  33. Fundamental of Electrical Engineering The induced torque of the motor is zero at synchronous speed. The torque speed curve is nearly linear between no-load and full-load. In this range, the rotor resistance is much larger than the rotor reactance. So, the rotor current increasing linearly. There is maximum possible torque that cannot be exceeded (called pullout torque or breakdown torque) is 2-3 times the rated full-load torque. Starting torque on motor is slightly larger than full-load. The torque on the motor for a given slip varies as the square of the applied voltage. If the rotor of the induction motor is driven faster than synchronous speed, then the direction of the induced torque in the machine reverse and become generator. If motor turning backward, relative to the direction of the magnetic field, the induced torque will stop the machine very rapidly and will try to rotate it in the other direction (called plugging). Semester II 09/10

  34. Fundamental of Electrical Engineering Induction Motor : Speed Control • By pole changing • By line frequency control • By line voltage control • By changing the rotor resistance Semester II 09/10 Note: 1 h.p = 746 Watts

  35. Fundamental of Electrical Engineering SYNCHRONOUS MACHINE Semester II 09/10

  36. Fundamental of Electrical Engineering Synchronous Machine : Introduction Transformer – energy transfer device. (transfer energy from primary to secondary) - form of energy remain unchanged. (Electrical) (DC/AC) Machines – electrical energy is converted to mechanical or vice versa. Semester II 09/10 • Motor operation • The field induced voltage, E permits the motor to draw power from the line to be converted into mechanical power. This time, the mechanical output torque is also developing. The induced voltage is in opposition to the current flow-called counter emf.

  37. Fundamental of Electrical Engineering Generator operation The field induced voltage, E is in the same direction as the current and is called the “generated voltage”. The machine torque opposes the input mechanical torque that is trying to drive the generator, and it is called the counter torque. Semester II 09/10 • Generally, the magnetic field in a machine forms the energy link between the electrical and mechanical systems. • The magnetic field performs two functions: • Magnetic attraction and repulsion produces mechanical torque (motor operation) • The magnetic field by Faraday’s Law induces voltages in the coils of wire. (generator operation)

  38. Fundamental of Electrical Engineering Synchronous Machine : Construction Have an outside stationary part, (stator) The inner rotating part (rotor) The rotor is centered within the stator. Air gap - the space between the outside of the rotor and the inside of the stator Semester II 09/10 Origin of name: syn = equal, chronos = time Synchronous machines are called ‘synchronous’ because their mechanical shaft speed is directly related to the power system’s line frequency.

  39. Fundamental of Electrical Engineering STATOR • The stator of a synchronous machine carries the armature or load winding which is a three-phase winding. • The armature winding is formed by interconnecting various conductors in slots spread over the periphery of the machine’s stator. Semester II 09/10 • When current flows in the winding, • each group produces a magnetic pole having a polarity dependent on the current direction, and a magnetomotive • force (mmf) proportional to the current magnitude.

  40. Fundamental of Electrical Engineering ROTOR • 2 types of rotors • - cylindrical (or round) rotors • - salient pole rotors. • Salient pole rotor less expensive than round rotors • and rotate at lower speeds • The rotor carries the field winding. The field current or the excitation current is provided by an external dc source. • Synchronous machine rotors are simply rotating electromagnets built to have as many poles as are produced by the stator windings. • Dc currents flowing in the field coils surrounding each pole magnetize the rotor poles. The magnetic field produced by the rotor poles locks in with a rotating stator field, so that the shaft and the stator field rotate in synchronism. Semester II 09/10

  41. Fundamental of Electrical Engineering Synchronous GENERATOR 1. GENERATOR The rate of rotation of the magnetic fields in the machine is related to the stator electrical frequency, given as: Semester II 09/10 The internal generated voltage of a synchronous generator is given as, This equation shows the magnitude of the voltage induced in a given stator phase.

  42. The per phase equivalent circuit Fundamental of Electrical Engineering Semester II 09/10

  43. Fundamental of Electrical Engineering Voltage Regulation: • If the generator operates at a terminal voltage VTwhile supplying a load corresponding to an armature current Ia, then; • In an actual synchronous machine, the reactance is much greater than the armature resistance, in which case; • Among the steady-state characteristics of a synchronous generator, its voltage regulation and power-angle characteristics are the most important ones. As for transformers, the voltage regulation of a synchronous generator is defined at a given load as; Semester II 09/10

  44. Fundamental of Electrical Engineering Phasor Diagram: The phasor diagram is to shows the relationship among the voltages within a phase (Eφ,Vφ, jXSIA and RAIA) and the current IA in the phase. Semester II 09/10

  45. Fundamental of Electrical Engineering Lagging P.F Semester II 09/10 Leading P.F.

  46. Pconv Fundamental of Electrical Engineering Power and Torque: In generators, not all the mechanical power going into a synchronous generator becomes electric power out of the machine The power losses in generator are represented by difference between output power and input power shown in power flow diagram below. Semester II 09/10

  47. Fundamental of Electrical Engineering Losses: • Rotor • - resistance; iron parts moving in a magnetic field causing currents to • be generated in the rotor body • - resistance of connections to the rotor (slip rings) • Stator • - resistance; magnetic losses (e.g., hysteresis) • Mechanical • - friction at bearings, friction at slip rings • Stray load losses • - due to non-uniform current distribution Semester II 09/10

  48. The input mechanical power is the shaft power in the generator given by equation: The power converted from mechanical to electrical form internally is given by The real electric output power of the synchronous generator can be expressed in line and phase quantities as and reactive output power Fundamental of Electrical Engineering Semester II 09/10

  49. Fundamental of Electrical Engineering In real synchronous machines of any size, the armature resistance RA is more than 10 times smaller than the synchronous reactance XS (Xs >> RA). Therefore, RA can be ignored Semester II 09/10

  50. Fundamental of Electrical Engineering Synchronous MOTOR Semester II 09/10

More Related