1 / 29

i Badge V1.0

i Badge V1.0. Contents: Properties Sensors Bluetooth interface Inferfacing iBadge SW development Energy monitoring Speech processing PCB / Enclosure. Presented by Ivo Locher. Aim of iBadge. Investigate behavior of children in a Kindergarten

heba
Télécharger la présentation

i Badge V1.0

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. iBadgeV1.0 • Contents: • Properties • Sensors • Bluetooth interface • Inferfacing iBadge • SW development • Energy monitoring • Speech processing • PCB / Enclosure Presented by Ivo Locher

  2. Aim of iBadge • Investigate behavior of children in a Kindergarten • Research subject for embedded systems / position tracking / wireless networks /speech recognition • Basis for further applications

  3. Properties of iBadge • Speech recording / replaying • Position detection • Direction detection / estimation (compass) • Tilt • Weather data: Temperature, Humidity, Pressure, Light

  4. BlockdiagramiBadge

  5. iBadge components • ATMEGA 103L- 128kB Flash, 4kB SRAM, 4kB EEPROM- 4MHz Clock, 32kHz timer- QFP package • DSP TMS320VC5416- 64kB DA RAM, 64kB SA RAM, Harvard- 8MHz ext. clock, up to 160MHz internal clock (PLL)- flexBGA package

  6. Data exchange • DSP Host-Port  AVR address / data bus • 8Bit • Hardware interrupt driven • Host-Port enables AVR to access entire memory space of DSP

  7. Sensor specs • Temperature- 16Hz Fs, -55 to +125oC, 0.25 K/LSB • Battery current monitoring*- 16Hz, various resolutions: 0.626 – 2.44 mA/LSB • Accelerometer**- 10Hz Fs, +/- 2g, duty cycle • Microphone- 16kHz Fs, 16Bit/sample (Codec), 20kHz BW

  8. Sensor specs (cont’d) • Position tracking (ultrasound, RFM)- 10Hz, 10cm resolution • Weather sensors (humidity, pressure, light)**- 400Hz, analog • Magnetic field*- 15Hz, +/- 6gauss, analog • * On board calibration / ** external calibration

  9. Sensor specs (cont’d)

  10. interface • Fc = 2.400 – 2.483 GHz • GFSK, BT = 0.5 • Nominal output power = 0 dBm (1mW) • Frequency hopping with 79 channels • Approx 1Mb/s, TDMA, time slot=625 s • Distance: 10..30m (1mW)

  11. Bluetooth (cont’d) • 1 Master, 7 Slaves • Asymmetric mode w/ 723.2kb/s downlink, 57.6kb/s uplink (ACL) • Symmetric mode with 433.9 kb/s (SCO) • 3 simultaneous synchronous voice channels with 64kb/s

  12. Bluetooth (cont’d) • EricssonROK 101 007 • ARM7-Thumb • Programmable • UART used(460kB/s) • RFCOMM

  13. Interfacing iBadge • Connector board- RS232 connection between PC, AVR, BT- JTAG interface toDSP debugging- free RS232 from/to AVR (i.e. for a terminal)

  14. Connector board (35x80mm) • Top Bottom

  15. Interfacing with RS232 • 3 connections (RS232):- BT  AVR- BT  PC- PC  AVR

  16. Connection • PC AVR- Download of AVR-SW and DSP-SW into Flash / EEPROM of AVR- Download-SW / cable provided by Atmel- File format: Intel HEX-File- AVR-SW runs on TinyOS- AVR boots up DSP over Host-Interface

  17. Connection (cont’d) • BT  PC- configuring/programming of BT interface- download of a separate program running on the BT module- sending data from PC over BT • BT  AVR- normal running mode of iBadge- future: programming of AVR / DSP

  18. SW Development Scenario • AVR-SW development on Atmel Compiler,testing / debugging over RS232 • DSP-SW development with TI Code Composer Studio,testing / debugging over JTAG interface

  19. Scenario (cont’d) • Stand-alone version:- DSP-SW must be included in AVR-SW (as binary array, *.abs)- AVR-SW (including DSP-SW) download over RS232 interface / storing in Flash on AVR- Boot up: AVR-SW starts / keeps DSP in reset- DSP-SW download over host interface (8 Bit) - DSP releasing from reset and DSP-SW starts

  20. Energy monitoring • 4 Battery monitors:- Entire circuit - All sensors- DSP - Bluetooth • On/off-switching of partial circuits:- All sensors - Only weather sensors- DSP - Bluetooth

  21. Tree structure Switching / battery monitors are controlled by AVR

  22. Battery • Li-Ion • Voltage: 3.6V • Capacity: 700mAh (= 9kJ) • Approx. battery life, when everything is on all the time: 3.5h • estimated battery life for normal operation: 5.4h

  23. Motivation for Energy Monitoring • Find optimal scheme what most energy efficient is, i.e.:- Codec: speech compression/feature extraction vs transmitted data computational power consumption vs radio (BT) power consumption

  24. Motivation (cont’d) • Run entire or parts of iBadge in a mode, which is most energy efficient.=> duty cycle (Sung Park) Power up Power down t T

  25. Speech processing • Implementation of different Codecs G.722 (G.729, proprietary) • Front-end processing of speech on iBadge • Seamless switching between them  Energy efficiency / data rate / recognition rate

  26. Codec G.722 • Output data rate: 64kb/s • 7 kHz analog BW

  27. PCB (62.5 x 47mm) Top Bottom

  28. PCB (cont’d) • PCB size: 62.5 x 47mm (same width as battery) • 4 signal layers / 6 power planes with separate analog plane • 0.006” tracks / 0.004” clearance • Additional small board (7mm), perp. for acceleration sensor(z-axis)

  29. Enclosure Prototype Pocket clip Finally: a customized enclosure

More Related