1 / 34

Audiocodes Gateway overview

Audiocodes Gateway overview. VoIP Bootcamp Training. Gateway overview. F oreign e X change (FX) signaling was originally developed to connect remote Private Branch Exchanges (PBX's) to the Central Office - provide dial tone from ‘Foreign office’ to local central offices

jela
Télécharger la présentation

Audiocodes Gateway overview

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Audiocodes Gateway overview VoIP Bootcamp Training

  2. Gateway overview • Foreign eXchange (FX) signaling was originally developed to connect remote Private Branch Exchanges (PBX's) to the Central Office - provide dial tone from ‘Foreign office’ to local central offices • FXS – Foreign eXchange Station / Subscriber • Behaves like a PBX • FXS is generally connected to analog phones (FXS is ground start and phones are loop start) • Connects to other subscriber equipment (fax/modem) • Supplies ring, voltage, and dial tone

  3. Gateway overview • FXO – Foreign eXchange Office • Behaves like a Telephone • Provides on-hook/off-hook indication (loop closure) • FXO is generally connected to analog POTS lines (FXO is loop start and is connected to ground start CO/PBX lines)

  4. Signaling Loop Start – FXO • 2-wire connection between central office and customer premises • TIP • RING • -48VDC signal between TIP and RING (usually powered by CO) • Phone goes off hook, completing circuit between TIP and RING • Central office senses draw of current from the line and sends dial tone

  5. Signaling FXO Problem – Glare • phenomenon associated with a call coming in to a line at the same time a call is trying to be made • Can deal with this using hunt methods • (e.g. Channel Select Mode – cyclic ascending)

  6. Signaling Ground Start • Designed to eliminate the problem of glare (CO – PBX environment) • Uses a ‘handshaking’ mechanism to avoid glare • TIP and RING circuit – • PBX will monitor TIP to check for open circuits • PBX will ground RING to send DC signal to CO • CO will monitor RING lead to check for signals from PBX • CO grounds the TIP lead to close the circuit when seizing trunk

  7. Signaling • Ground start process • Designed to eliminate the problem of glare • Ring has the battery voltage on the CO side • At customer premise (PBX) side, the RING lead is grounded causing current to flow from the RING lead • Central office senses the RING ground and in turn grounds the TIP lead • PBX senses the TIP ground reply from the CO and closes the loop to the RING ground

  8. Signaling • MP-11x/MP-10x and Mediant 1000 FXO modules support Loop Start signaling • MP-11x/MP-10x, and Mediant 1000 FXS modules support and Ground Start signaling • In 5.0 modules can be either all Ground Start or all Loop Start • Controlled by parameter ‘GroundKeyDetection’ • 0 = Loop Start • 1 = Ground Start • More to come…

  9. FXO Gateway • IP to TEL • FXO receives INVITE from the IP side • FXO sends back 100 Trying • FXO seizes line (according to channel select mode) • FXO sends 183 Session Progress • FXO dials the digits to the line • When finished dialing the FXO opens the voice to the IP side • FXO sends 200 OK • NOTE – this is One Stage dialing process. Two stage dialing is used in PBX environments

  10. FXO Gateway

  11. FXO Gateway • NOTE: MP11x FXO with version 4.8 firmware NO LONGER USES COEFFECIENT FILES!! • FXO now uses regional settings in config files. AC says all FXO gateways shipped in N. America will be sent with regional setting already configured. • Parameter is ‘CountryCoefficients’ for MP11x FXO and Mediant 1000 FXO modules • FXS still use coefficient files

  12. Audiocodes MP11x Configuration Basics

  13. Cabling your MP-1xx / 11x

  14. Assigning an IP address to MP-11x • To assign an IP address to the MP-11x use one of the following methods: • HTTP using a Web browser • BootP • Serial communication software (connected to the MP-11x via the RS-232 port)

  15. Assigning an IP address to MP-11x • MP-11x ships from the factory with default network settings

  16. Assigning an IP address using HTTP • Steps to follow: • Connect your computer to the MP-11x • network interface on your computer to a port on a network hub, connection from MP-11x to port on same hub. • Ethernet cross-over cable from computer NIC to the RJ-45 jack on the MP-11x • NOTE: for either of these, you must configure your PC’s NIC IP address to same subnet as the MP-11x default network setting.

  17. Assigning an IP address using HTTP • Access the MP-11x Embedded Web Server • ‘Quick Setup’ screen • Set the ‘IP Address’, ‘Subnet Mask’ and ‘Default Gateway IP Address.’ • NOTE: ensure your settings correspond with your network’s IP settings

  18. Assigning an IP address using HTTP • Access the MP-11x Embedded Web Server

  19. Assigning an IP address using HTTP • Click the ‘Reset’ button and click ‘OK’ when prompted • Device applies the changes and restarts – this process takes 1 –2 minutes • ‘Ready’ and ‘LAN’ LEDs are lit green • Reconnect MP-11x to network if necessary • Reset any IP addresses if necessary

  20. Assigning an IP address using BootP

  21. Assigning an IP address using BootP • BootP application is available on MP-11x CD

  22. Assigning an IP address using BootP • Requires: • MP-11x MAC address • Client MAC field is checked (responses to BootP requests) • IP address • Subnet Mask • Default gateway address • Resetting the MP-11x

  23. Assigning IP address using RS-232 port • Use HyperTerminalTMto console into device • settings are available in MP-11x user manual • CLI requires basic commands • ‘Conf’ (configuration mode) • ‘GCP IP’ (Get Current Parameters IP) • ‘SCP IP’ [ip address] [subnet mask] [default gateway] • This is the command that sets your IP address • ‘SAR’ (Save and Reset)

  24. Troubleshooting Tips

  25. Troubleshooting • Audio quality issues • Check / reload coefficient files • Ensure correct ‘Start’ method (loop vs. start) • Check jitter buffer levels / jitter buffer optimization • AC recommends ’10’ for optimization, I3 recommends 7 (7/70) • This setting scheduled to appear in Gateway Configurator (?) • Dynamic jitter buffer value indicates minimum size, not maximum – can adjust • Echo issues: • Coefficient files • Check CO line readings (this is part of the analog tail circuit)

  26. Troubleshooting • Debugging / Message Log • The web interface on an Audiocodes gateway allows for easy access and configuration of the device • Debug setting allows logging to be viewed and exported • ACSyslog application: • provided by Audiocodes • Message logs exported to ACSyslog and converted to .txt

  27. Troubleshooting

  28. Troubleshooting • Audiocodes gateways provide various levels of Debugging, depending on firmware versions. • Changes in firmware also causes updates to web interface, which often moves the location of the setting within the web interface.

  29. Troubleshooting • Command – line parameters also available for setting debug levels: • EnableSyslog = 1 • SyslogServerIP = (IP address of PC running ACSyslog) • GWDebugLevel = 5

  30. Troubleshooting • Debug level 6 is for H.323 only!! • The debug level indicates how verbose the logging will be: the higher the setting, the more logging information you will get. A debug level of ‘0’ indicates that debugging is off. • Audiocodes recommends setting debug to 5 • Ensure logging is turned back down to ‘0’ after troubleshooting

  31. Troubleshooting • Set Debug level in web interface

  32. Troubleshooting Direct Message log to export to Syslog server

  33. Troubleshooting • Syslog server presents SIP messages • These can be easily viewed and saved to a .txt file

  34. Audiocodes Analog Training • Questions??

More Related