1 / 12

Real NACE CIP Level 1 NACE-CIP1-001 Exam Questions Killtest - 100% Passing Materials

We are providing Real NACE CIP Level 1 NACE-CIP1-001 Exam Questions Killtest as the 100% passing materials for all the professionals who want to attempt NACE-CIP1-001 Coating Inspector Level 1 Exam. You can use real NACE-CIP1-001 exam questions and accurate answers to prepare for the NACE NACE-CIP1-001 exam. You can access Killtest NACE-CIP1-001 pdf and testing engine online to read all NACE-CIP1-001 exam Q&As.

killtestfreedemo2020
Télécharger la présentation

Real NACE CIP Level 1 NACE-CIP1-001 Exam Questions Killtest - 100% Passing Materials

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 2020 NACE-CIP1-001 Exam Questions KillTest Coating Inspector Level 1

  2. Question 1 When applying Thermal Spray Coatings the specification is most likely to refence: A. SSPC PA 2 B. NACE SP 0178 C. NACE SP 0188 D. SSPC-CS 23.00/AWS C2.23/NACE No. 12 Answer: D

  3. Question 2 What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge? A. 1 cm (.39 inch) B. 2.5 cm (1 inch) C. 6.35 cm (2.5 inch) D. 2.5 millimeters (.10 inch) Answer: B

  4. Question 3 Polymerization is the process of: A. Monomers telegraphing B. Monomers joining together C. All thermoplastic coatings D. All organic coatings Answer: B

  5. Question 4 An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called A. cracking. B. sagging. C. holiday. D. checking. Answer: C

  6. Question 5 Relative humidity is A. a measure of the amount of moisture in the air compared to saturation level. B. a measure of the amount of moisture in the air compared to the air temperature. C. the lowest temperature at which moisture forms on a steel surface. D. the highest temperature at which moisture forms on a steel surface. Answer: A

  7. Question 6 Upon arrival of coating materials, the inspector should A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations. B. observe and document the amount of material and batch numbers. C. observe aryl document that the applicator WFT at regular intervals during application. D. observe and document time frame and environmental conditions between each coat. Answer: B

  8. Question 7 Galvanic corrosion occurs on which of the following substrates: A. Concrete B. Fiberglass Reinforced Plastic C. Metal D. Wood Answer: C

  9. Question 8 If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a A. dry film thickness (DEI) measurement. B. wet film thickness (WFT) measurement. C. blotter test for the presence of oil and water. D. vial lest. Answer: C

  10. Question 9 Dew point is the temperature at which A. water freezes. B. humidity decreases C. condensation occurs. D. the air is saturated. Answer: C

  11. Question 10 You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: A. Break the blisters to see what's inside B. Document the problem and advise the Contractor and Owner's representative C. Document the problem and advise the Contractor D. Extract any liquid that may be inside the blister and send it to the lab for further analysis Answer: B

  12. Thank You sales@killtest.com

More Related