1 / 59

CHAPTER (7) Attributes Control Charts

CHAPTER (7) Attributes Control Charts. Data that can be classified into one of several categories or classifications is known as attribute data. Classifications such as conforming and nonconforming are commonly used in quality control.

murphyb
Télécharger la présentation

CHAPTER (7) Attributes Control Charts

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CHAPTER (7) Attributes Control Charts

  2. Data that can be classified into one of several categories or classifications is known as attribute data. Classifications such as conforming and nonconforming are commonly used in quality control. Another example of attributes data is the count of defects. Introduction

  3. Control Charts for Fraction Nonconforming • Fraction nonconforming is the ratio of the number of nonconforming items in a population to the total number of items in that population. • Control charts for fraction nonconforming are based on the binomial distribution.

  4. Control Charts for Fraction Nonconforming Recall: A quality characteristic follows a binomial distribution if: 1. All trials are independent. 2. Each outcome is either a “success” or “failure”. 3. The probability of success on any trial is given as p. The probability of a failure is 1-p. 4. The probability of a success is constant.

  5. Control Charts for Fraction Nonconforming • The binomial distribution with parameters n  0 and 0 < p < 1, is given by • The mean and variance of the binomial distribution are

  6. Design of Fraction Nonconforming Chart • Three parameters must be specified • The sample size • The frequency of sampling • The width of the control limits • Common to base chart on 100% inspection of all process output over a period of time • Rational subgroups may also play role in determining sampling frequency

  7. Sample size • If p is very small, we should choose n sufficiently large to find at least one nonconforming unit • Otherwise the presence of only one non-conforming in the sample would indicate out-of-control condition (example) • To avoid this, choose n such that the probability of finding at least one nonconforming per sample is at least γ(example)

  8. p = 0.01andn = 8 If there is one nonconforming in the sample, then p =1/8=0.125 and we conclude that the process is out of control Example

  9. The sample size can be determined so that the probability of finding at least one nonconforming unit per sample is at least γ Example p = 0.01 and γ = 0.95 Find n such that P(D ≥ 1) ≥ 0.95 Using Poisson approximation of the binomial with λ=np From cumulative Poisson table λmust exceed 3.00  np ≥ 3  n ≥ 300 Sample size

  10. The sample size can be determined so that a shift of some specified amount,  can be detected with a stated level of probability (50% chance of detection). UCL = pout If  is the magnitude of a process shift, then n must satisfy: Therefore, Sample size

  11. The sample size n, can be chosen so that the lower control limit would be nonzero: and Positive Lower Control Limit

  12. Interpretation of Points on the Control Chart for Fraction Nonconforming

  13. Variable Sample SizeVariable-Width Control Limits

  14. Variable Sample SizeControl Limits Based on an Average Sample Size

  15. Variable Sample SizeThe Standardized Control Chart

  16. The Opening Characteristic Function and Average Run Length Calculations

  17. Control Charts for Nonconformities (Defects)Procedures with Constant Sample Size

  18. There are many instances where an item will contain nonconformities but the item itself is not classified as nonconforming. • It is often important to construct control charts for the total number of nonconformities or the average number of nonconformities for a given “area of opportunity”. The inspection unit must be the same for each unit.

More Related