1 / 54

Robotic Kinematics – the Inverse Kinematic Solution

Robotic Kinematics – the Inverse Kinematic Solution. ME 3230 Kinematics and Mechatronics Dr. R. Lindeke. Cartesian Space. Joint Space. Joint Space. FKS vs. IKS. In FKS we built a tool for finding end frame geometry from Given Joint data:

rusti
Télécharger la présentation

Robotic Kinematics – the Inverse Kinematic Solution

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Robotic Kinematics – the Inverse Kinematic Solution ME 3230 Kinematics and Mechatronics Dr. R. Lindeke ME 3230

  2. Cartesian Space Joint Space Joint Space FKS vs. IKS • In FKS we built a tool for finding end frame geometry from Given Joint data: • In IKS we need Joint models from given End Point Geometry: Cartesian Space ME 3230

  3. So this IKS Problem is Nasty (in Mathematics this is considered a Hard Modeling Issue) • It a more difficult problem because: • The Equation set is “Over-Specified”: • 12 equations in 6 unknowns • Space can be “Under-Specified”: • Planer devices with more joints than 2 • The Solution set can contain Redundancies: • Multiple solutions • The Solution Sets may be un-defined: • Unreachable in 1 or many joints ME 3230

  4. But the IKS is VERY Useful – some Uses of IKS include: • Building Workspace Maps • Allow “Off-Line Programming” solutions • The IKS allows the engineer to equate Workspace capabilities with Programming realities to assure that execution is feasible(as done in ROBCAD & IGRIP) • The IKS Aids in Workplace Design and Operational Simulations ME 3230

  5. Doing a Pure IKS solution: the R Manipulator R Frame Skeleton (as DH Suggest!) Same Origin Point! ME 3230

  6. LP Table and Ai’s ME 3230

  7. FKS is A1*A2: ME 3230

  8. Forming The IKS: In the Inverse Problem, The RHS MATRIX is completely known (perhaps from a robot mapped solution)! And we use these values to find a solution to the joint equations that populate the LHS MATRIX ME 3230

  9. If 2 Matrices are Equal then EACH and EVERY term is also Uniquely equal as well! Forming The IKS: • Examining these two matrices • n, o, a and d are “givens” in the inverse sense!!! • (But typically we want to build general models leaving these terms unspecified) • Term (1, 4) & (2,4) on both sides allow us to find an equation for : • (1,4): C1*(d2+cl2) = dx • (2,4): S1*(d2+cl2) = dy • Form a ratio to build Tan(): • S1/C1 = dy/ dx • Tan  = dy/dx •  = Atan2(dx, dy) ME 3230

  10. Forming The IKS: • After  is found, back substitute and solve for d2: • (1,4): C1*(d2+cl2) = dx • Isolating d2: d2 = [dx/Cos1] - cl2 ME 3230

  11. Alternative Method – “doing a pure inverse approach” • Form A1-1 then pre-multiply both side by this ‘inverse’ • Leads to: A2 = A1-1*T0ngiven ME 3230

  12. Simplifying & Solving: • Selecting and Equating (1,4) • 0 = -S1*dx + C1*dy • Solving: S1*dx = C1*dy • Tan() = (S1/C1) = (dy/dx) •  = Atan2(dx, dy) – the same as before • Selecting and Equating (3,4) -- after back substituting  solution • d2 + cl2 = C1*dx + S1*dy • d2 = C1*dx + S1*dy - cl2 ME 3230

  13. Performing IKS For Industrial Robots: (a more involved problem) • First let’s consider the concept of the Spherical Wrist Simplification: • All Wrist joint Z’s intersect at a point • The ‘n Frame’ is offset from this Z’s intersection point at a distance dn (the hand span) along the a vector of the desired solution (3rd column of desired orientation sub-matrix!) which is the z direction of the 3rd wrist joint • This follows the DH Algorithm design tools as we have learned them! ME 3230

  14. Performing IKS – with a Spherical Wrist • We can now separate the POSE effects: • ARM joints • Joints 1 to 3 in a full function manipulator (without redundant joints) • They function to maneuver the spherical wrist to a target POSITIONrelated to the desired target POSE • WRIST Joints • Joints 4 to 6 in a full functioning spherical wrist • Wrist Joints function as a primary tool to ORIENT the end frame as required by the desired target POSE ME 3230

  15. Performing IKS: Focus on Positioning • We will define a point (called the WRIST CENTER) where all 3 z’s intersect as: • Pc = [Px, Py, Pz] • We find that this position is exactly: Pc = dtarget - dn*a • Px = dtarget,x - dn*ax • Py = dtarget,y - dn*ay • Pz = dtarget,z - dn*az Note: dn is the so called ‘Handspan’ (a CONSTANT) ME 3230

  16. Treating the Arm Types (as separate robot entities): • Cartesian (2 types) • Cantilevered • Gantry • Cylindrical • Spherical (w/o d2 offset) • 2 Link Articulating (w/o d2 offset) ME 3230

  17. Cantilevered Cartesian Robot J2 J3 X0 P-P-P Configuration Y0 Z0 J1 ME 3230

  18. Gantry Cartesian Robot P-P-P Configuration X0 Z0 Y0 J3 J2 J1 ME 3230

  19. Cylindrical Robot • Doing IKS – given a value for: • X, Y and Z of End • Compute , Z and R Z0 R Y0 X0 ME 3230

  20. Spherical Robot • Developing a IKS (model): • Given Xe, Ye, & Ze • Compute ,  & R  R Z0 Y0 X0 ME 3230

  21. 2-Link Articulating Arm Manipulator Z0 3 L2 L1 X0 Y0 2 1 ME 3230

  22. Focusing on the ARM Manipulatorsin terms of Pc: • Prismatic: • q1 = d1= Pz (its along Z0!) – cl1 • q2 = d2 = Px or Py - cl2 • q3 = d3= Py or Px - cl3 • Cylindrical: • 1 = Atan2(Px, Py) • d2 = Pz – cl2 • d3 = Px/C1 – cl3 {or +(Px2 + Py2).5 – cl3} ME 3230

  23. Focusing on the ARM Manipulatorsin terms of Pc: • Spherical: • 1 = Atan2(Px, Py) • 2 = Atan2( (Px2 + Py2).5 , Pz) • D3 = (Px2 + Py2 + Pz2).5 – cl3 ME 3230

  24. Focusing on the ARM Manipulatorsin terms of Pc: • Articulating: • 1 = Atan2(Px, Py) • 3 = Atan2(D, (1 – D2).5) • Where D = • 2 =  -  •  is: Atan2((Px2 + Py2).5, Pz) •  is: ME 3230

  25. Focusing on the ARM Manipulators in terms of Pc: • 2 = Where D = Atan2((Px2 + Py2).5, Pz) - ME 3230

  26. One Further Complication Must Be Considered: • This is called the d2 offset problem • A d2 offset is a problem that states that the nth frame has a non-zero offset along the Y0 axis as observed in the solution of the T0n with all joints at home • (like the 5 dof articulating robots in our lab!) • This leads to two solutions for 1 the So-Called “Shoulder Left” and “Shoulder Right” solutions ME 3230

  27. Defining the d2 Offset issue Here: ‘The ARM’ might contain a prismatic joint (as in the Stanford Arm – discussed in text) or it might be the a2 & a3 links in an Articulating Arm as it rotates out of plane A d2 offset means that there are two places where 1 can be placed to touch a given point (and note, when 1is at Home, the wrist center is not on the X0 axis!) ME 3230

  28. Lets look at this Device “From the Top” – a ‘plan’ view of the structure projected to the X0 Y0 plane F1  11 ME 3230

  29. Solving For 1: • We will have a Choice of two poses for 1: ME 3230

  30. This device (like the S110 robots in lab) is called a “Hard Arm” Solution • We have two 1’s • These lead to two 2’s (Spherical) • One for Shoulder Right & one for Shoulder Left • Or four 2’s and 3’s in the Articulating Arm: • Shoulder Right  Elbow Up & Down • Shoulder Left  Elbow Up & Down ME 3230

  31. Now, lets look at Orientation IKS’s • Orientation IKS again relies on separation of joint effects • We (now) know the first 3 joints control positions • they would have been solved by using the appropriate set of equations developed above • The last three (wrist joints) will control the achievement of our desired Orientation ME 3230

  32. These Ideas Lead to an Orientation Model for a Device that is Given by: • This ‘model’ separates Arm Joint and Wrist Joint Contribution to the desired Target Orientation • Note: target orientation is a ‘given’ for the IKS model! ME 3230

  33. Focusing on Orientation Issues • Lets begin by considering ‘Euler Angles’ (they are a model that is almost identical to a full functioning Spherical Wrist as defined using the D-H algorithm!): • Step 1, Form a Product: • Rz1*Ry2*Rz3 • This product becomesR36 in the model on the previous slide ME 3230

  34. Euler Wrist Simplified: this matrix, which contains the joint control angles, is then set equal to a ‘U matrix’ prepared by multiplying the inverse of the ARM joint orientation sub-matrices and the Desired (given) target orientation sub-matrix: NOTE: R03 is Manipulator dependent! (Inverse required a Transpose) ME 3230

  35. Continuing: to define the U-Matrix Rij are terms from the product of the first 3 Ai’s (rotational sub-matrix) ni, oi & ai are from given target orientation – we develop our models in a general way to allow computation of specific angles for specific cases ME 3230

  36. Now Set: LHS (euler angles) = RHS (U-Matrix) U as defined on the previous slide! (a function of arm-joint POSE and Desired End-Orientation) ME 3230

  37. Solving for Individual Orientation Angles (1st solve for ‘’ the middle one): • Selecting (3,3) C= U33 • With C we “know” S = (1 - C2).5 • Hence:  = Atan2(U33, (1-U332).5) • NOTE: leads to 2 solutions for ! ME 3230

  38. Re-examining the Matrices: • To solve for : Select terms: (1,3) & (2,3) • CS = U13 • SS = U23 • Dividing the 2nd by the 1st: S /C = U23/U13 • Tan() = U23/U13 •  = Atan2(U13, U23) ME 3230

  39. Continuing our Solution: • To solve for : Select terms: (3,1) & (3,2) • -SC = U31 • SS = U32 (and dividing this by previous) • Tan() = U32/-U31 (note sign migrates with term!) •  = Atan2(-U31, U32) ME 3230

  40. Summarizing: •  = Atan2(U33, (1-U332).5) •  = Atan2(U13, U23) •  = Atan2(-U31, U32) Uij’s as defined on the earlier slide! – and – U is manipulator and desired orientation dependent ME 3230

  41. Let consider a Spherical Wrist: Same Origin Point Here drawn in ‘Good Kinematic Home’ – for attachment to an Articulating Arm ME 3230

  42. IKSing the Spherical Wrist ME 3230

  43. Writing The Solution: Uij’s as defined on the earlier slide! – and – U is manipulator and desired orientation dependent ME 3230

  44. Let’s Solve(here I try the ‘Pure Inverse’ Technique): Note: R4’s Inverse ME 3230

  45. Simplifying ME 3230

  46. Solving: • Let’s select Term(3,3) on both sides: • 0 = C4U23 – S4U13 • S4U13 = C4U23 • Tan(4) = S4/C4 = U23/U13 • 4 = Atan2(U13, U23) • With the givens and back-substituted values (from the arm joints) we have a value for 4 andthe RHS is completely known! ME 3230

  47. Solving for 5 & 6 • For 5: Select (1,3) & (2,3) terms • S5 = C4U13 + S4U23 • C5 = U33 • Tan(5) = S5/C5 = (C4U13 + S4U23)/U33 • 5 = Atan2(U33, C4U13 + S4U23) • For 6: Select (3,1) & (3, 2) terms • S6 = C4U21 – S4U11 • C6 = C4U22 – S4U12 • Tan(6) = S6/C6 = ([C4U21 – S4U11]/[C4U22 – S4U12]) • 6 = Atan2 ([C4U22 – S4U12], [C4U21 – S4U11]) ME 3230

  48. Using the Pure Inversing: • We removed ambiguity from the solution • We were able to solve for joints “In Order” • Without noting – we see the obvious relationship between Spherical wrist and Euler Orientation! ME 3230

  49. Summarizing: • 4 = Atan2(U13, U23) • 5 = Atan2(U33, C4U13 + S4U23) • 6 = Atan2 ([C4U22 – S4U12], [C4U21 – S4U11]) ME 3230

  50. Lets Try One: • Cylindrical Robot w/ Spherical Wrist • Given would be a Target matrix from Robot Mapping! (it’s an IKS after all!) • The d3 “constant” is 400mm; the d6 offset (the ‘Hand Span’) is 150 mm. • 1 = Atan2((dx – ax*150),(dy-ay*150)) • d2 = (dz – az*150) • d3 = ((dx – ax*150)2+p(dy-ay*150)2).5 - 400 ME 3230

More Related