1 / 9

Checking antenna system with sun noise

Checking antenna system with sun noise. Why the sun?. The sun is most powerful radio source seen from the earth. The next powerful radio source is Cassiopeia which is 100 times weaker than the sun. The sun noise can even be detected with smaller antennas (as mines)

sereno
Télécharger la présentation

Checking antenna system with sun noise

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Checking antenna system with sun noise

  2. Why the sun? • The sun is most powerful radio source seen from the earth. • The next powerful radio source is Cassiopeia which is 100 times weaker than the sun. • The sun noise can even be detected with smaller antennas (as mines) • The pointing system can follow the sun • Is visible during day!

  3. Setup of equipment #1 EPFL PC with audacity MixWDownloader Audio Voltmeter true RMS Preamp +20dB Gain 1dB nF Transverter 437mc to 29mc 20dB Gain(EPFL filter and postamp)

  4. Setup of equipment #2 • Point the antenna to 40deg. elevation az to north (not in the direction of the sun!) • When preamp, transverter (postamp @EPFL) is switched ON the S-Meter on the RX should clearly increase and the with moderate Audio in speaker the increase of noise is well to hear. (watch video s_meter.mpg) [as with ICOM!] • Set the RX frequency close to 437.502mc. • Listen carefully that you hear no signal! (move VFO knob slightly up and down to check that there is no signal to hear)

  5. Setup of equipment #3 • The whole system should be linear working (not saturated in any stage, this is the most critical point to ensure this. Sometimes you have to repeat all the steps to check if you get always the same result) • Set sensitivity of Voltmeter so that it indicates around 0dB. • Reduce audio output of RX to reach about 0dB if the 10dB steps are to big.

  6. Setup of equipment #4 • Disable AGC of RX. (The audio output should increase very much because it was reduced before by the agc [and indicated by the S_Meter] . • With the manual rf-gain control knob set the audio that the voltmeter shows again the same value as before. Don’t touch audio volume at that moment!! • Set sensitivity of Voltmeter so that it indicates around 0dB. • Reduce audio output to reach the about 0dB if the 10dB steps are to big. [only small correction]

  7. Measuring the increase of noise • Now we are ready to watch the increase of the sun noise in the audio • “Watch” because it is very difficult the hear a slight increase with our ears. (listen to the example sunnoise.wav it is difficult to say when you hear the sun) • Look to the voltmeter and let now point the antenna to the sun. • If all is well it stops at the maximum. (watch increase.mpg for my system) • If not adjust AZ and EL and note the difference in deg. >> Offset for the pointing system. Repeat after offset, all steps!

  8. Expected results • If the nF of your preamp is close to 1dB and the gain about 20dB • With the “big filter” and the postamp (actually 30dB) • The increase of noise due to the sun must be bigger than for mine and about 3 to 4 dB! • The gain of your antenna is much higher than mines. • (With much bigger antennas you can detect the noise of sun via the moon [moon noise] and other comic sources)

  9. BKP

More Related