1 / 39

ME 4447/6405

ME 4447/6405. Microprocessor Control of Manufacturing Systems and Introduction to Mechatronics Instructor: Professor Charles Ume Lecture #7. Product Family and Designations. RAM – Random Access Memory “Volatile” – loses contents after power off ROM – Read Only Memory “non-Volatile”

tara
Télécharger la présentation

ME 4447/6405

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ME 4447/6405 Microprocessor Control of Manufacturing Systems and Introduction to Mechatronics Instructor: Professor Charles Ume Lecture #7

  2. Product Family and Designations

  3. RAM – Random Access Memory • “Volatile” – loses contents after power off • ROM – Read Only Memory • “non-Volatile” • Contents must be programmed at the factory • EPROM – Electrically Programmable Read Only Memory • “non-Volatile” • Electrically programmable • May be erasable with ultraviolet light if manufacturer included window in chip package • Still considered Read Only Memory during normal program execution • EEPROM – Electrically Erasable Programmable Read Only Memory • “non-Volatile” • Electrically programmable and erasable (Note:Sometimes higher voltage than microcontroller voltage may be required) • Slower to write to than RAM so still considered Read Only Memory during normal program execution

  4. Product Designations found in literature is shown below: Read:MC9S12C32 Device User Guide V01.14 HCS12 Microcontrollers: MC9S12C128 Rev 01.23

  5. Product Family Members as of 3/2008

  6. MC9S12C package options and block diagram

  7. MC9S12C-Family package options: • 48-pin Low-profile Quad Flat Package (LQFP) • 52-pin Low-profile Quad Flat Package • 80-pin quad flat package (QFP) (Shown)

  8. MC9S12C-Family Block Diagram shows available subsystems Figure1-1. MC9S12C-Family Block Diagram

  9. Data Direction and Data Register Data Direction Register (DDR) Used to indicate direction of data flow in a port Example configure pins 0, 3, 5 and 7 of port A as output pins Note: By default all port pins are input pins DDRA ($0002)should be loaded with: #%10101001 or #$A9 Assembly code to accomplish the above: LDAA #$A9 STAA $0002 Data Register Used to control state of devices connected to output pins Used to determine state of devices connected to input pins Suppose 4 different light bulbs are to be turned on and off from these output pins:

  10. Data Direction and Data Register • Port A data Register address is $0000 • To turn light bulbs connected to PA0 and PA3 on: • Store #%00001001 or #$09 at address $0000 • LDAA #$09 • STAA $0000 • To turn all light bulbs connected to PA0, PA3, PA5 and PA7 on: • Store #%10101001 or #$A9 at address $0000 LDAA #$A9 STAA $0000

  11. Data Direction and Data Register Suppose you want to determine state of machines connected to input pins PA1, PA2, PA4 and PA6: You load accumulator A with content of address $0000 In accumulator A: If logic 1 is written in bits 1 and 4 respectively: That will mean that devices connected to PA1 and PA4 have been turned on In accumulator A: If logic 1 is written in bits 1, 2, 4 and 6: That will mean that all devices connected to PA1, PA2, PA4 and PA6 are on

  12. . . . Figure 6. Register and Control Bit Assignments (Programming Reference) Excerpt of Detailed Register Map (Device User Guide)

  13. . . .

  14. Excerpt of Detailed Register Map (Device User Guide)

  15. MC9S12C-Family hardware mode selection, hardware mode connections, and hardware mode memory maps

  16. Hardware Mode Selection Summary (Reference Manual) MODA, MODB, & MODC may be writable in software after startup, see Reference

  17. HCS12 Features • 80 pin HCS12 • Crystal Frequency is 16 Mhz • Clock Frequency is 8 Mhz Therefore, 1 clock cycle = 0.125micro second • Normal Expanded Wide

  18. HCS12 Stretching • MC9S12C32 external clock (ECLK) feature called Stretching slows down system clock • Occurs when microcontroller is accessing external memory • Has unintended consequence: • Operation time depends on whether internal or external memory is being accessed • If you want to achieve 0.125 micron sec per clock cycle: • You should write your program in internals RAM, starting from $0800.

  19. HCS12 Stretching • Most people start their codes from $1000, which is in external RAM. • Other option is to write your program in Flash EEPROM. • Not best course of action for program development: • Flash memory may be written to finite number of times • Reference Manual, pp 116,151

  20. Hardware Mode External Connections • In Single Chip mode, Ports A, B and E available as general purpose input/output pins • In Normal Expanded Mode, Ports A and B form 16-bit Address and 8-bit Data bus, Port E provides control signals for external devices • In Normal Expanded Wide mode, Ports A and B form 16-bit Address and 16-bit Data bus, Port E provides control signals for external devices

  21. Note: Map depends on state of ROMON and ROMHM bits

  22. Axiom CML-12C32 memory maps & interrupt vectors

  23. Axiom CML-12C32 Evaluation Board MC9S12C32 Solderless Breadboard Serial Port Oscillator Power Jack Address Demultiplexer Reset MCU Port External SRAM

  24. Default Configuration: • MODC = 1 • MODA = MODB = 0  Single Chip Mode • MODA and MODB may be changed in software to permit use of Expanded Wide mode once after each reset • Internal Flash Memory is available only if ROMON is enabled • At the rising edge of Reset, the state of pin PP[6]/KWP[6]/ROMCTL is latched to the ROMON bit. • ROMCTL = 1  ROMON Enabled, Flash memory available • ROMCTL = 0  ROMON Disable, Flash memory unavailable • For operation in this class, ROMON will be Enabled, so do not pull PP[6] low on Reset!

  25. Axiom CML-C32 • Single chip mode • ROMON Enabled • MON12 not in use • (CodeWarrior) • MODA = 0 • MODB = 0 • Internal User RAM available: • $0800-$0FFF • User can put a program in Internal Flash$8000-$FEFF • Ports A and B available for use

  26. Axiom CML-C32 • Single chip mode • ROMON Enabled • MON12 in use • MODA = 0; MODB = 0 • Internal User RAM available: • $0800-$0DFF • Stack Location: $0E00 – $0E5F • Mon12 RAM Interrupt Vector: $0F8A – 0FFF • User can put a program in Internal Flash $8000-$BEFF and Internal RAM • Ports A and B available for use MON12 is located here

  27. Axiom CML-C32 • Expanded Wide mode • ROMON Enabled • MON12 not in use(CodeWarrior) • MODA = 1 • MODB = 1 • Internal User RAM available: • $0800-$0FFF • External User RAM available: • $0400-$07FF • $1000-$7FFF • User can put a program in Internal Flash $8000-$FEFF • Ports A and B NOT available for use

  28. Axiom CML-C32 • Expanded Wide mode • ROMON Enabled • MON12 in use • MODA = 1; MODB = 1 • Internal User RAM available: • $0800-$0DFF (Run AXIDE) • Monitor Utility Jump Table: • $FF10-$FF67 • External User RAM available: • $0400-$07FF • $1000-$7FFF • User can put a program in Internal Flash $8000-$B7FF and RAM • Ports A and B NOT available for use • Stack Location: $0E00 – $0E5F • Mon12 RAM Interrupt Vector: • $0F8A – 0FFF MON12 is located here MON12 is located here

  29. Interrupt Vector Table • Mon12 NOT in use • Standard S12C32 Interrupt Jump Table • Each vector is 2 bytes. User stores address of interrupt service routine in appropriate vector • 0x is same as $: It is used when writing program in C

  30. Interrupt Vector Table • Mon12 NOT in use • Standard S12C32 Interrupt Jump Table • Each vector is 2 bytes. User stores address of interrupt service routine in appropriate vector

  31. Standard S12C32 Interrupt Jump Table (MON12 not in use) The user can put the starting address of his/her subroutine Directly in the vector field of the interrupt he/she wants to Use. Example: If the user wants to use the IRQ interrupt, he/she can put the starting address of his/her subroutine directly in vector fields oxFFF2 and oxFFF3

  32. Interrupt Vector Table • MON12 in use • Standard S12C32 Interrupt Vector Jump Table is not available with MON12 • MON12 supplies alternate Interrupt Jump Table • User’s interrupt service routine must be stored in $4000-$7FFF (External RAM) if Autostart is to be used Monitor Interrupt Vector Table (CML-C32 User’s Guide)

  33. Monitor Interrupt Vector Table (CML-C32 User’s Guide) To use the vector table, the user again writes the address of the interrupt service routine to the location given in the table. For example, to use the IRQ interrupt to call an interrupt service routine located at address ISR_ADDR, the user writes the following code: MOVW #$0800, $0FF2 OR MOVW #ISR_ADDR, $0FF2 LDD #$0800 STD $0FF2 During initialization MON12 writes $0000 to all vectors in the Monitor Interrupt vector Table to cause any unscheduled interrupt to cause a trap. Any nonzero value will cause the S12C32 to jump to the interrupt service routine located at that value.

  34. Relationship Between Standard S12C32 Interrupt Vectors and MON12 Interrupt Table Vectors • When MON12 is in use, it reconfigures standard interrupt vector table to $0F8A - $0FFF, and user may not override these values. • During initialization, MON12 clears contents of Monitor Interrupt Table. • If interrupt occurs and corresponding vector contains $0000 • MON12 perceives this as error and restarts monitor program, ending execution of user code. • Standard interrupt table is located in Flash EEPROM and cannot be written to using MON12. • When writing programs in C, BDM cable is used to program HCS12 and standard interrupt table is used.

  35. Mon12 Commands

  36. Several subroutines from Mon12 exist that are available for performing I/O tasks. Utility subroutines available to the user are as follows:

  37. Assume an interrupt is enabled in the main program, e.g. IRQ Signal is received by the MC from IRQ pin MC will finishing executing the current instructions I-bit in the CCR is set to 1 (this will cause any incoming maskable interrupt to queue up) CPU registers are pushed in the Stack Starting address of the interrupt Sub-routine to be executed is fetched from the IRQ vectors This Sub-routine is executed and the last instruction is RTI The execution of the RTI will cause all the data in the Stack to be pulled out and put back in their respective registers The last 2-byte data pulled out are the Program Counter High and Low bytes address The MC will use these 2-byte address to know where to get the next instruction to be executed Interrupt Acknowledgement

More Related