How to Check and Replace an Outboard Motor Impeller

1. How to Check and Replace an Outboard Motor Impeller? A Step-by-Step Guide When you're out on the water, the last thing you want is engine trouble. One of the most crucial, yet often overlooked, components of your outboard motor is the water pump impeller. This small part is responsible for circulating cooling water through the engine, preventing it from overheating. A faulty impeller can lead to a damaged engine, so knowing how to check and replace an outboard motor impeller is essential for any boat owner. Why Impeller Maintenance is Crucial An impeller is a rubber or neoprene part that sits inside the water pump housing. As it spins, it pulls water from the lake or ocean and pushes it through the cooling passages of your engine. Over time, the flexible blades of the impeller can become brittle, cracked, or worn, reducing its ability to

2. pump water effectively. This is especially true for engines that are used in saltwater or those that sit for long periods. Regular checks and replacements are key to ensuring your engine's longevity and reliability. For Yamaha outboard motors,Honda outboard motors, and Tohatsu outboard motors, the general principle of impeller replacement is similar, though the specific tools and procedures may vary slightly. Most manufacturers recommend replacing the impeller every 100 hours of use or once a year, whichever comes first. Tools and Materials You'll Need Before you begin, gather the following tools and materials: ● New water pump kit: This usually includes the impeller, housing gaskets, and a new key or pin. ● Socket set and wrenches: To remove the lower unit and housing bolts. ● Screwdrivers: For various screws. ● Pliers: To help with small parts. ● Gasket sealant: A quality marine sealant to prevent leaks. ● Degreaser and clean rags: For cleaning the housing. ● Grease: Marine grease for reassembly. Step-by-Step Guide to Replacing the Impeller Step 1: Disconnect the Lower Unit First, ensure your boat is on a stable surface and the engine is off. Remove any trim tabs or anodes that might be in the way. Locate the bolts that hold the lower unit to the midsection of the motor. These are typically found on the side and front of the motor. Use your socket wrench to carefully loosen and remove these bolts. On some Yamaha outboard motors and Honda

3. outboard motors, there may be a shift linkage to disconnect as well. Be sure to follow your owner's manual for the exact location of all bolts and linkages. Step 2: Remove the Water Pump Housing With the lower unit separated, you can now access the water pump housing. This is usually located at the top of the lower unit. The housing is held in place by a few bolts. Remove these bolts to lift off the housing cover. Take note of any dowel pins or gaskets as you remove the cover. Step 3: Inspect and Remove the Old Impeller Once the cover is off, you'll see the impeller. Inspect the old impeller for signs of wear, such as cracks, bent blades, or a brittle feel. Also, check the inside of the housing for any debris or damage. A common sign of a failing impeller is a squealing or hissing sound from the motor while running, or a weak stream of water from the tell-tale hole. To remove the old impeller, simply pull it straight up and off the drive shaft. You may need to use a pair of pliers to get a good grip. Be sure to note the orientation of the blades and the key or pin that locks the impeller to the shaft. Step 4: Install the New Impeller Before installing the new impeller, clean the housing and shaft thoroughly. Apply a thin layer of marine grease to the drive shaft. Slide the new key or pin into the slot on the shaft. Then, carefully slide the new impeller onto the shaft, aligning the keyway with the key. You'll need to twist the impeller in the direction of engine rotation as you push it down to seat the blades correctly. This is a critical step for all motors, including Tohatsu outboard motors and Honda outboard motors. Step 5: Reassemble the Water Pump

4. Place a new gasket on the lower unit, then carefully lower the housing cover back into place. Ensure the dowel pins align correctly. Tighten the housing bolts in a cross-pattern to ensure even pressure. Step 6: Reattach the Lower Unit Before reattaching the lower unit, apply a new gasket and a thin layer of marine grease to the splines of the driveshaft. Carefully lift the lower unit and align it with the engine's midsection, ensuring the driveshaft and shift linkage align. Reinstall all bolts and linkages you removed in Step 1. Tighten all bolts to the manufacturer’s specified torque. Step 7: Final Check Once everything is back together, it's time to test your work. Start the engine in a test tank or with a set of earmuffs. Watch for a strong, steady stream of water from the tell-tale hole. If the stream is weak or non-existent, shut off the engine immediately and double-check your work. Properly maintaining your outboard motor's impeller is a simple task that can prevent major headaches and costly repairs. By following this guide, you can ensure your engine stays cool and runs reliably for years to come, whether you own a Yamaha outboard motor, a Honda outboard motor, or a Tohatsu outboard motor. Don’t let a small part ruin your big day on the water! For all your boating needs, from expert service to a wide selection of parts and accessories, trust Fawcett Boat Supplies. Visit the website to explore an extensive inventory and learn more about how they can help you keep your boat in perfect shape.