1 / 26

Health and Safety & Risk Assessment for users of Brunel 007 (W7) - Composites Manufacturing Laboratory

Health and Safety & Risk Assessment for users of Brunel 007 (W7) - Composites Manufacturing Laboratory. Staff associated with composite modules in W7. academic Stephen Grove John Summerscales technicians Richard Cullen, Greg Nash, Richard Kenyon researchers

Pat_Xavi
Télécharger la présentation

Health and Safety & Risk Assessment for users of Brunel 007 (W7) - Composites Manufacturing Laboratory

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Health and Safety& Risk Assessment for users of Brunel 007 (W7) - Composites Manufacturing Laboratory

  2. Staff associated with composite modules in W7 • academic • Stephen Grove • John Summerscales • technicians • Richard Cullen, Greg Nash, Richard Kenyon • researchers • post-doc and research degree candidates

  3. Principal material groups • Resins • unsaturated polyester (UPE) • epoxide/epoxy (Ep) • phenolic • Thermoplastics • polypropylene (PP) • nylon (PA: polyamide) • polyester (PET: polyethylene terephthalate) • poly ether ether ketone (PEEK) • Fibres • aramid (Kevlar, Twaron) • carbon • glass (usually E-glass) • Solvents, release agents, etc

  4. Health and Safety • Control of Substances Hazardous to Health (COSHH) • can you substitute a safer material • can you use an engineering solution • are you using appropriate personal protection • Environmental Protection Act • you must dispose of materials in the correct manner • A clean and tidy workplace is a safer workplace • if you are not using it put it away • if you must leave anything out, make sure it is clearly labelled

  5. Health and Safety: Unsaturated PolyEster resin (UPE) • base resin: polymer chains with reactive sites (50%) • styrene: reactive diluent (50%) • volatile • flammable: • flash point 31 degrees Centigrade, explosive limits 1.1-8.0% • NO SMOKING, no naked flames • toxic: • (inhalation) ODOUR threshold 25 ppm (Scandinavian Occupational Exposure Limit) • little inhalation irritation <210 ppm (UK OEL is 100 ppm 8h TWA) • irritating to nose and throat above 500 ppm • NIOSH IDLH (Immediately Dangerous to Life or Health) at 700 ppm • (ingestion) IRRITATING to mouth, throat and stomach • may lead to vomiting and dizziness • harmful effects at >4 g/kg of body weight • (skin contact) IRRITATING: evident as itching and redness • frequent or prolonged contact leads to dermatitis • degreases skin • (eye contact) IRRITATION may last several hours

  6. Styrene odour andtime weighted average occupational exposure levels (OEL) ** see for Lecture C4 webpage for sources **

  7. Health and Safety: Unsaturated PolyEster resin (UPE) • COSHH • substitution: resin without styrene (eg epoxy) or low styrene emission resin • Engineering controls • general ventilation to reduce background level • local exhaust ventilation with flow away from operator • use shielded rollers to reduce droplet cloud • protection:lab coat, barrier cream, gloves, goggles • Disposal to waste solvent bottle if resin uncured

  8. Health and Safety: Unsaturated PolyEster resin (UPE) • Peroxide Initiator (usually added as 1-2%) • acetyl acetone peroxide (AAP), benzoyl peroxide (BzO2),hydrogen peroxide (H2O2), methyl ethyl ketone peroxide (MEKP) • SEVERE IRRITANTS to skin • CAUSE BURNS: wash immediately for 15 minutes with waterand obtain doctors attention • CORROSIVE to moist tissue (eyes, nose, throat, airways to lungs) • Irreversible damage may be caused to eyes by prolonged contact • avoid contact between MEKP and rust • BzO2: EXTREME RISK OF EXPLOSION by shock, friction, fire or ignition • COSHH • substitution: different resin system? • engineering controls: use as a dilute solution if practicable • protection: protective clothing, face/eye protection • Handle and open container with care • Ignition: contact with combustible material may cause fire • do not mop up with e.g. paper cloths • Disposal do not empty into drains

  9. acetyl acetone peroxide (AAP) • 2,4-pentanedione peroxide solution • CAS 37187-22-7 a.k.a. Luperox 224 • Formula: C10H14O6 • Density: 1.177 g/cm3 • Melting Point: ≥60 °C (SADT) • Boiling Point: 301.9 °C at 760 mmHg • Flash Point: 129.7 °C • Hazard Symbols: O; C • Risk Codes: 20/22-34-7 • Safety: 26-36/37/39-45-3/7-14 • Transport Information: UN 3105 5.2 peroxide >

  10. Health and Safety: unsaturated polyester resin • accelerators (1-2%) • cobalt-based solutions in styrene (cobalt naphthenate or cobalt-octoate) • amine-based 25% solution in styrene • toxic if swallowed, inhaled or allowed to remain in contact with the skin • fumes from burning accelerators contain toxic materials

  11. Health and Safety: Unsaturated PolyEster resin (UPE) never, never, nevermix catalyst (initiator)directly with accelerator: they will form an explosive mixture

  12. Health & Safety: Epoxy resin (Ep) • Base resin • mild to moderate primary skin irritants • irritation potential increased by prolonged skin contact • EPOXY SENSITIZATION: • skin reddens in close proximity to uncured resin • For all curing agents • wear protective clothing and goggles • ventilation is essential

  13. Health & Safety: epoxy resin curing agents • aliphatic amines • alkaline caustic materials • cause burns and severe tissue damage to skin, mucous membranes and eyes • ALL contact should be avoided • solid aromatic amines • less caustic, less irritating and less sensitising than aliphatic amines • diaminodiphenylmethane (DAPM) is toxic/known to cause liver damage in humans • DAPM can be absorbed through the skin so all contact should be avoided • cycloaliphatic amines • variable in their irritation and sensitising effect • extremely irritating to the eyes • polyamides • skin irritants of varying sensitivity, but generally non-sensitising to the skin • extremely irritating to the eyes

  14. Health & Safety: thermoplastics • generally chemically inert • need to be processed at high temp. • beware of molten polymer (hot!)

  15. Health & Safety: Reinforcement Fibres • respirable dust is believed to have a particle size of <3 μm • for safety, 5 μm is assumed • reinforcement fibre diameters are in the range 6-15 μm • carbon and glass fibres are not expected to break into lengths shorter than the diameter • aramid (and polyethylene) fibres have a complex microstructure and may fibrillate into particles of <3 μm (respirable?) • all reinforcements should be regarded as a nuisance dust when cutting/machining • control limits are 10 mg/m3 total dust • 5 mg/m3 forman-made mineral fibre • disposal • all man-made fibres are a notifiable wasteand must be disposed of into the bagged bins provided

  16. Health & Safety: ancillary materials • you are also likely to use .... • solvents • release agents • etcetera • the Material Safety Data Sheet (MSDS)is there to be read, then you compilea risk assessment specific to the taskbefore you start work

  17. Health & Safety: sharps • you will be working with potentially dangerous chemicals • they need not be harmful if they are treated with respect • the most common entries in the Accident Book are cuts from knives or from sharp edges on demoulding

  18. First Aid at Work plus ... • The nominated First Aiders for Brunel are: • Steve Edmonds, 2.32536 Brunel W15 • Tony Tapp, 2.32539 Brunel W14 • heavy structures laboratory near Brunel south door • Cumberland Centre Minor Accident Unit  567999 • Royal Eye Infirmary (Derriford)  0845 155 8094 • In an emergency, call Security first on 33333,(Security can than expedite the services once on site)then ring for external services using 9.999

  19. Health & safety: summary • Remember to: • read and follow suppliers safety sheet and instructions for use • store and handle materials in the appropriate safe way • consider alternative materials and engineering controls • use ventilation and fume/dust control equipment properly • wear appropriate personal protection • good housekeeping is essential foryour safety and that of your colleagues

  20. Health & safety: summary • do not: • eat, drink (or smoke), in the laboratory or storage areas • mix peroxide initiator with accelerator • allow waste to accumulate • use solvents for cleaning skin • use combustible materials to soak up spillage

  21. and if in doubt ... ask !!

  22. Risk assessment • really, this is simple: • probability * severity = risk factor (RF) • if RF is high, then how can it be reduced? • http://www.tech.plym.ac.uk/sme/mats324/risk.htm

  23. Risk assessment • probability order 1 = unlikely 1:100 2 = possible 1:10000 3 = probable 1:100000 • http://www.tech.plym.ac.uk/sme/mats324/risk.htm

  24. Risk assessment • severity example 1 = minor pierced skin 2 = serious broken limb 3 = critical life-changing • http://www.tech.plym.ac.uk/sme/mats324/risk.htm

  25. Risk assessment • remember, risk factor is calculated • risk factor (RF) = probability * severity 1-3 = low risk 4 = medium risk 6 or 9 = high risk • RF cannot be 5, 7 or 8 • http://www.tech.plym.ac.uk/sme/mats324/risk.htm

  26. Some people do stupid things … • The winners of the competition: safety at work • Russian mechanics study airbag deployment • Construction workers • The Galway Car Recovery incident • DeWalt power tools • Petrol tanker in Paraguay and mobile-phone-as-a-light

More Related