1 / 24

Introduction to evaporation

Introduction to evaporation. Food1040 module Malcolm Povey University of Leeds.

alicia
Télécharger la présentation

Introduction to evaporation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Introduction to evaporation Food1040 module Malcolm Povey University of Leeds

  2. The liquid feed moves on the "hot" inner walls in an evaporator. Heat is continuously transferred from the outside of the wall to the inside, thereby heating up the liquid to the boiling point where water evaporates from the liquid feed. Evaporator basics http://www.apv.com/anhydro/evapo/anhevap.htm

  3. Liquid distribution One of the most important issues influencing the effectiveness of the evaporation is the distribution of the liquid on the inner walls. To make the evaporation effective the liquid film on the inner walls should be as thin as possible. However, if the film is too thin, the product will burn on the walls, therefore it is very important to be able to control the thickness of the film also known as "the wetting rate". http://www.apv.com/anhydro/evapo/anhevap.htm

  4. Typical applications Milk and milk productsSweetened condensed milkWPC35, WPC60 and WPC80Whey and whey permeateFruit juice (tropical, citrus, temperate)Coffee, teaSugar (different types)Vitamins, pharmaceuticalsVarious teas and herb extracts

  5. More applications • Various proteins e.g. blood or gelatineVarious broths e.g. chicken beefBulk chemicalsWaste water: • Spent waste water (distilleries) • General waste water

  6. The principles of evaporation The product to be concentrated is separated from the heating medium by a tube wall, or a flat curved plate. The typical heating medium is steam or vapour. The system can be evacuated in order to lower the boiling temperature. The evaporated vapour can be reused as heating medium often in combination with either mechanical or thermal recompression. (Regeneration)

  7. Heat and mass transfer are connected The laboratory CFE

  8. Heat transfer in a CFE q ~(θs - θp) More specifically :- Equation 1 q = U.A. (θs - θp) = U.A. Δθ Where A = heat exchange area = 0.251 m2   U = overall heat transfer coefficient θs = average steam temperature in the calandria jacket θp = product temperature at boiling point (boiling set point)

  9. Energy consumption As evaporation is a very energy consuming process, the availability and relative cost of energy determine the design of the evaporation plant. Normally an evaporation plant is designed to use the energy as efficiently as possible by using more than one effect. Therefore the following technical solutions are used in order to keep the temperature of the steam high enough to run the process:

  10. Optimising energy use • Thermal Vapour Recompression (TVR) • Mechanical Vapour Recompression (MVR) or • combination of both • Shown below is a figure illustrating the relation between the number of effects and energy consumption under standard conditions for a typical product. • Furthermore, the figure also shows a rough correlation between steam and electrical energy consumption per kg water evaporated, allowing the customer to estimate, whether the price of electric power in his local area justifies the use of MVR instead of TVR.

  11. Comparison http://www.apv.com/anhydro/evapo/anhevap.htm

  12. Evaporator pictures and applications

  13. Single effect recompression • Corn Syrup • Gelatin • Salt • Soybean Oil • Steepwater • Sugar • Whey

  14. Falling Film Plate & Tubular Evaporators •       The unique liquid distribution • Short residence time • Low temperature difference • with • Single pass operation • Even shorter residence time • Larger capacities • Typical applications are: • Milk, whey and milk products • Fruit juices , Various vitamins , Pharmaceuticals • Essence recovery

  15. Falling film evaporator http://www.swenson-equip.com/vrml.html

  16. Rising/Falling Film Plate Evaporators • The unique liquid distribution • Short residence time • Low temperature difference • Typical applications are: • Milk, whey and milk products • Fruit juices • Various vitamins • Pharmaceuticals • Essence recovery

  17. Rising Film Plate Evaporators • APV´s rising film plate evaporators (Paravap) are particularly effective in processing high viscous liquids. • Typical applications are: • High viscous sugar • Fruit puree and pulp • High viscous pharmaceuticals • Polymers

  18. Other evaporators http://www.swenson-equip.com/index.html

  19. Forced circulation evaporator

  20. Evaporator Diagrams

  21. Falling film evaporator

  22. Forced Convection with steam jet recompression

  23. Multiple effect evaporator

  24. Wiped Film Evaporator

More Related