1 / 28

PALESTINE UNIVERSITY

PALESTINE UNIVERSITY. BUILDING MATERIAL. chapter No.#4. Steel. STEEL General.

amal
Télécharger la présentation

PALESTINE UNIVERSITY

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PALESTINE UNIVERSITY BUILDING MATERIAL chapter No.#4 Steel

  2. STEEL General Steel is a structural material which consists mostly of iron and carbon. It can, however, contain other additives which might change the steel's properties. Steel can be hot rolled or cold formed into structural shapes, such as the familiar "I" beam known today as a wide flange. Steel has the same strength in tension as it has in compression, unlike concrete.

  3. STEELGeneral There are some tests for steel must be applied as : tension test: this test used to measure the material properties of a steel (or really any material, for that matter), Beam bending test: this test used to measure the material properties of a specimen and the effectiveness of the orientation of the beam.

  4. STEELGeneral Some types of steel are specifically for use in fabricating large structures. They are called ‘high-strength lowalloy’ or HSLA steels. These steels are: much stronger and tougher than ordinary carbon steels ductile highly formable weld able Highly resistant to corrosion - which is important since the structure may be in place for a long time.

  5. STEEL Why HSLA Steels are Strong:- The starting point in achieving the desirable properties of structural steels is to get the composition of the alloy right. The extra strength can be achieved through various combinations of alloying elements which means that there can be some choice in the other properties that the steel will have. A typical HSLA steel will contain about 0.15% carbon, 1.65% manganese and low levels (under 0.035%) of phosphorous and sulphur and additions of other elements:

  6. STEEL Microstructure of HSLA steels The strength of all steels, including HSLA steels, comes from their microstructure. Strength is increased by: • increasing the amount of pearlite • increasing the fineness of the grains structure • increasing the amount of hard precipitate.

  7. STEEL Chemical Composition of Structural Steels The primary types of structural steel are usually classified according to the following chemical composition categories: Carbon-manganese steels High-strength, low-alloy (HSLA) steels High-strength quenched and tempered alloy steels

  8. STEEL Carbon manganese Steels whose primary chemical components are carbon and manganese in addition to iron, are referred to as carbon steelsor mild structural steels. The materials of this type are generally least expensive; they have quite adequate strength and ductility characteristics, and are therefore by far the most widely used grades. One of the most prominent of these steels are ASTM grade A36, with a specified minimum yield stress of36 ksi.

  9. STEEL High-strength, low-alloy (HSLA) steels represent a relatively recent development in steelmaking. The higher strength (42 to 65 ksi) is achieved by adding small amounts of additional chemical elements. Two of the most common HSLA steels are ASTM grade A572 and A588. High-strength quenched and tempered alloy steels:- used for structural purposes are essentially available only as grade A514 today. With a yield stress level of 90 to 100 ksi, the increase in strength is achieved through heat treatment. A514 is available only in plate form, up to 6 inches thick.

  10. STEELsome elements used in structural steels: Carbon (C) Manganese (Mn) Aluminum (Al) Chromium (Cr) Columbium (Cb) Copper (Cu) Molybdenum (Mo) Nickel (Ni) Phosphorus (P) and Sulfur (S) Silicon (Si) Vanadium (V) Other chemical elements

  11. STEELSteel Alloys Steel Alloys can be divided into five groups • Carbon Steels • High Strength Low Alloy Steels •  Quenched and Tempered Steels • Heat Treatable Low Alloy Steels • Chromium-Molybdenum Steels Carbon steels are normally classified as shown below.

  12. STEEL classification of Carbon steel • Low-carbon steels:- contain up to 0.30 weight percent C. The largest category of this class of steel is flat-rolled products (sheet or strip) usually in the cold-rolled and annealed condition. The carbon content for these high-formability steels is very low, less than 0.10 weight percent C, with up to 0.4 weight percent Mn.  For rolled steel structural plates and sections, the carbon content may be increased to approximately 0.30 weight percent, with higher manganese up to 1.5 weight percent.

  13. STEEL classifications of Carbon steel • Medium-carbon steels:- • are similar to low-carbon steels except that the carbon ranges from 0.30 to 0.60 weight percent and the manganese from 0.60 to 1.65 weight percent. Increasing the carbon content to approximately 0.5 weight percent with an accompanying increase in manganese allows medium-carbon steels to be used in the quenched and tempered condition.

  14. STEEL classifications of Carbon steel • High-carbon steels:- contain from 0.60 to 1.00 weight percent C with manganese contents ranging from 0.30 to 0.90weight percent.

  15. STEEL classifications of Carbon steel • High-strength low-alloy (HSLA) steels, or micro alloyed steels, are designed to provide better mechanical properties than conventional carbon steels. They are designed to meet specific mechanical properties rather than a chemical composition.  The chemical composition of a specific HSLA steel may vary for different product thickness to meet mechanical property

  16. STEEL classifications of Carbon steel • Requirements. The HSLA steels have low carbon contents (0.50 to ~0.25 weight percent C) in order to produce adequate formability and weld ability, and they have manganese contents up to 2.0 weight percent. Small quantities of chromium, nickel, molybdenum, copper, nitrogen, vanadium, niobium, titanium, and zirconium are used in various combinations.

  17. STEEL Structural Steel Sections • Steel Material with Large Cross-section Steel material with large cross-section

  18. STEEL Structural Steel Sections • Thin Steel Plate:-

  19. Tee Bares STEEL Structural Steel Sections

  20. Square tubing Hexagon bares Round bares Square bares Flat bares STEEL Structural Steel Sections

  21. Honed Shafting Round Shafting I Beam Section STEEL Structural Steel Sections

  22. STEEL Structural Steel Sections

  23. STEEL Market forms of Steel • Bar Size Shapes • Structural-Size Shapes • "W" Shapes • "HP" Shapes • "L" Shapes • "S" Shapes • "C" Shapes • "M" Shapes • "MC" Shapes

  24. STEEL Basic Definitions The nominal loads and load combinations shall be as stipulated by the applicable code under which the structure is designed or dictated by the conditions involved. In the absence of a code, the loads, including impact and crane loads, and load combinations, shall be those stipulated in ASCE 7. For design purposes, the loads stipulated by the applicable code or ASCE 7 shall be taken as nominal loads.

  25. STEEL Loads

  26. STEEL Trusses Trusses are structures composed entirely of two force members . They consists generally of triangular sub-element and are constructed and supported so as to prevent any motion.

  27. STEEL Trusses

  28. STEEL END

More Related