1 / 93

FLIGHT MECHANICS Exercise Problems

Problem 4.1. Consider the incompressible flow of water through a divergent duct. The inlet velocity and area are 5 ft/s and 10 ft2, respectively. If the exit area is 4 times the inlet area, calculate the water flow velocity at the exit.. Solution 4.1. Problem 4.2. 4.2 In the above problem calculate the pressure difference between the exit and the inlet. The density of water is 62.4 Ibm/ft3..

cade
Télécharger la présentation

FLIGHT MECHANICS Exercise Problems

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

    1. FLIGHT MECHANICS Exercise Problems CHAPTER 4

    2. Problem 4.1 Consider the incompressible flow of water through a divergent duct. The inlet velocity and area are 5 ft/s and 10 ft2, respectively. If the exit area is 4 times the inlet area, calculate the water flow velocity at the exit.

    3. Solution 4.1

    4. Problem 4.2 4.2 In the above problem calculate the pressure difference between the exit and the inlet. The density of water is 62.4 Ibm/ft3.

    5. Solution 4.2

    6. Problem 4.3 Consider an airplane flying with a velocity of 60 m/s at a standard altitude of 3 km. At a point on the wing, the airflow velocity is 70 m/s. Calculate the pressure at this point. Assume incompressible flow.

    7. Solution 4.3

    8. Problem 4.4 An instrument used to measure the airspeed on many early low-speed airplanes, principally during 1919 to 1930, was the venturi tube. This simple device is a convergent - divergent duct (The front section's cross-sectional area A decreases in the flow direction, and the back section's cross-sectional area increases in the flow direction. Somewhere in between the inlet and exit of the duct, there is a minimum area, called the throat.) Let A1 and A2 denote the inlet and throat areas, respectively. Let p1 and p2 be the pressures at the inlet and throat, respectively.

    9. The venturi tube is mounted at a specific location on the airplane (generally on the wing or near the front of the fuselage), where the inlet velocity V, is essentially the same as the freestream velocity that is, the velocity of the airplane through the air. With a knowledge of the area ratio A2/A1 (a fixed design feature) and a measurement of the pressure difference p1- p2 the airplane's velocity can be determined. For example, assume A2/A1 =1/4 and p1- p2 = 80 Ib/ft2. If the airplane is flying at standard sea level, what is its velocity?

    11. Problem 4.5 Consider the flow of air through a convergent-divergent duct, such as the venturi described in Prob. 4.4. The inlet, throat, and exit areas are 3, 1.5, and 2 m2 respectively. The inlet and exit pressures are 1.02 x 105 and 1.00 x 105 N/m2, respectively. Calculate the flow velocity at the throat. Assume incompressible flow with standard sea-level density.

    12. Solution 4.5

    13. Problem 4.6 An airplane is flying at a velocity of 130 mi/h at a standard altitude of 5000 ft. At a point on the wing, the pressure is 1750.0 Ib/ft2. Calculate the velocity at that point assuming incompressible flow.

    14. Solution 4.6

    15. Problem 4.7 Imagine that you have designed a low-speed airplane with a maximum velocity at sea level of 90 m/s. For your airspeed instrument, you plan to use a venturi tube with a 1.3 : 1 area ratio. Inside the cockpit is an airspeed indicatora dial that is connected to a pressure gauge sensing the venturi tube pressure difference p1- p2 and properly calibrated in terms of velocity. What is the maximum pressure difference you would expect the gauge to experience?

    16. Solution 4.7

    17. Problem 4.8 A supersonic nozzle is also a convergent-divergent duct, which is fed by a large reservoir at the inlet to the nozzle. In the reservoir of the nozzle, the pressure and temperature are 10 atm and 300 K, respectively. At the nozzle exit, the pressure is 1 atm. Calculate the temperature and density of the flow at the exit. Assume the flow is isentropic and, of course, compressible.

    18. Solution 4.8

    19. Problem 4.9 Derive an expression for the exit velocity of a supersonic nozzle in terms of the pressure ratio between the reservoir and exit po/pe and the reservoir temperature To.

    20. Solution 4.9

    21. Problem 4.10 Consider an airplane flying at a standard altitude of 5 km with a velocity of 270 m/s. At a point on the wing of the airplane, the velocity is 330 m/s. Calculate the pressure at this point.

    22. Solution 4.10

    23. Problem 4.11 The mass flow of air through a supersonic nozzle is 1.5 Ibm/s. The exit velocity is 1500 ft/s, and the reservoir temperature and pressure are 1000R and 7 atm, respectively. Calculate the area of the nozzle exit. For air, Cp = 6000 ft lb/(slug)(R).

    24. Solution 4.11

    25. Problem 4.12 A supersonic transport is flying at a velocity of 1500 mi/h at a standard altitude of 50,000 ft. The temperature at a point in the flow over the wing is 793.32R. Calculate the flow velocity at that point.

    26. Solution 4.12

    27. Problem 4.13 For the airplane in Prob. 4.12, the total cross-sectional area of the inlet to the jet engines is 20 ft2. Assume that the flow properties of the air entering the inlet are those of the freestream ahead of the airplane. Fuel is injected inside the engine at a rate of 0.05 Ib of fuel for every pound of air flowing through the engine (i.e., the fuel-air ratio by mass is 0.05). Calculate the mass flow (in slugs/per second) that comes out the exit of the engine.

    29. Problem 4.14 Calculate the Mach number at the exit of the nozzle in Prob. 4.11.

    31. Problem 4.15 A Boeing 747 is cruising at a velocity of 250 m/s at a standard altitude of 13 km. What is its Mach number?

    33. Problem 4.16 A high-speed missile is traveling at Mach 3 at standard sea level. What is its velocity in miles per hour?

    35. Problem 4.17 Calculate the flight Mach number for the supersonic transport in Prob. 4.12.

    37. Problem 4.18 Consider a low-speed subsonic wind tunnel with a nozzle contraction ratio of 1 : 20. One side of a mercury manometer is connected to the settling chamber, and the other side to the test section. The pressure and temperature in the test section are 1 atm and 300 K, respectively. What is the height difference between the two columns of mercury when the test section velocity is 80 m/s?

    39. Problem 4.19 We wish to operate a low-speed subsonic wind tunnel so that the flow in the test section has a velocity of 200 mi/h at standard sea-level conditions. Consider two different types of wind tunnels: (a) a nozzle and a constant-area test section, where the flow at the exit of the test section simply dumps out to the surrounding atmosphere, that is, there is no diffuser, and (b) a conventional arrangement of nozzle, test section, and diffuser, where the flow at the exit of the diffuser dumps out to the surrounding atmosphere. For both wind tunnels (a) and (b) calculate the pressure differences across the entire wind tunnel required to operate them so as to have the given flow conditions in the test section.

    40. For tunnel (a) the cross-sectional area of the entrance is 20 ft2, and the cross-sectional area of the test section is 4 ft2. For tunnel (b) a diffuser is added to (a) with a diffuser area of 18 ft2. After completing your calculations, examine and compare your answers for tunnels (a) and (b). Which requires the smaller overall pressure difference? What does this say about the value of a diffuser on a subsonic wind tunnel?

    41. Solution 4.19 (a)

    43. Problem 4.20 A Pitot tube is mounted in the test section of a low-speed subsonic wind tunnel. The flow in the test section has a velocity, static pressure, and temperature of 150 mi/h, 1 atm, and 70F, respectively. Calculate the pressure measured by the Pitot tube.

    45. Problem 4.21 The altimeter on a low-speed Piper Aztec reads 8000 ft. A Pitot tube mounted on the wing tip measures a pressure of 1650 Ib/ft2. If the outside air temperature is 500R, what is the true velocity of the airplane? What is the equivalent airspeed?

    47. Problem 4.22 The altimeter on a low-speed airplane reads 2 km. The airspeed indicator reads 50 m/s. If the outside air temperature is 280 K, what is the true velocity of the airplane?

    49. Problem 4.23 A Pitot tube is mounted in the test section of a high-speed subsonic wind tunnel. The pressure and temperature of the airflow are 1 atm and 270 K, respectively. If the flow velocity is 250 m/s, what is the pressure measured by the Pitot tube?

    50. Solution 4.23

    51. Problem 4.24 A high-speed subsonic Boeing 777 airliner is flying at a pressure altitude of 12 km. A Pitot tube on the vertical tail measures a pressure of 2.96 x 104 N/m2. At what Mach number is the airplane flying?

    53. Problem 4.25 A high-speed subsonic airplane is flying at Mach 0.65. A Pitot tube on the wing tip measures a pressure of 2339 Ib/ft2. What is the altitude reading on the altimeter?

    55. Problem 4.26 A high-performance F-16 fighter is flying at Mach 0.96 at sea level. What is the air temperature at the stagnation point at the leading edge of the wing?

    57. Problem 4.27 An airplane is flying at a pressure altitude of 10 km with a velocity of 596 m/s. The outside air temperature is 220 K. What is the pressure measured by a Pitot tube mounted on the nose of the airplane?

    59. Problem 4.28 The dynamic pressure is defined as q = 0.5rV2. For high-speed flows, where Mach number is used frequently, it is convenient to express q in terms of pressure p and Mach number M rather than r and V. Derive an equation for q = q(p,M).

    61. Problem 4.29 After completing its mission in orbit around the earth, the Space Shuttle enters the earth's atmosphere at very high Mach number and, under the influence of aerodynamic drag, slows as it penetrates more deeply into the atmosphere. (These matters are discussed in Chap. 8.) During its atmospheric entry, assume that the shuttle is flying at Mach number M corresponding to the altitudes h:

    62. Calculate the corresponding values of the freestream dynamic pressure at each one of these flight path points. Suggestion: Use the result from Prob. 4.28. Examine and comment on the variation of q8 as the shuttle enters the atmosphere.

    64. Problem 4.30 Consider a Mach 2 airstream at standard sea-level conditions. Calculate the total pressure of this flow. Compare this result with (a) the stagnation pressure that would exist at the nose of a blunt body in the flow and (b) the erroneous result given by Bernoulli's equation, which of course does not apply here.

    67. Problem 4.31 Consider the flow of air through a supersonic nozzle. The reservoir pressure and temperature are 5 atm and 500 K, respectively. If the Mach number at the nozzle exit is 3, calculate the exit pressure, temperature, and density.

    69. Problem 4.32 Consider a supersonic nozzle across which the pressure ratio is pe/po = 0.2. Calculate the ratio of exit area to throat area.

    71. Problem 4.33 Consider the expansion of air through a convergent-divergent supersonic nozzle. The Mach number varies from essentially zero in the reservoir to Mach 2.0 at the exit. Plot on graph paper the variation of the ratio of dynamic pressure to total pressure as a function of Mach number; that is, plot q/ po versus M from M = 0 to M = 2.0.

    73. Problem 4.34 The wing of the Fairchild Republic A-10A twin-jet close-support airplane is approximately rectangular with a wingspan (the length perpendicular to the flow direction) of 17.5 m and a chord (the length parallel to the flow direction) of 3 m. The airplane is flying at standard sea level with a velocity of 200 m/s. If the flow is considered to be completely laminar, calculate the boundary layer thickness at the trailing edge and the total skin friction drag. Assume the wing is approximated by a flat plate. Assume incompressible flow.

    75. Problem 4.35 In Prob. 4.34, assume the flow is completely turbulent. Calculate the boundary layer thickness at the trailing edge and the total skin friction drag. Compare these turbulent results with the above laminar results.

    77. Problem 4.36 If the critical Reynolds number for transition is 106, calculate the skin friction drag for the wing in Prob. 4.34.

    80. Problem 4.37 Let us reflect back to the fundamental equations of fluid motion discussed in the early sections of this chapter. Sometimes these equations were expressed in terms of differential equations, but for the most pan we obtained algebraic relations by integrating the differential equations. However, it is useful to think of the differential forms as relations that govern the change in flowfield variables in an infinitesimally small region around a point in the flow.

    81. (a) Consider a point in an inviscid flow, where the local density is 1.1 kg/m3. As a fluid element sweeps through this point, it is experiencing a spatial change in velocity of two percent per millimeter. Calculate the corresponding spatial change in pressure per millimeter at this point if the velocity at the point is 100 m/sec. (b) Repeat the calculation for the case when the velocity at the point is 1000 m/sec. What can you conclude by comparing your results for the low-speed flow in part (a) with the results for the high-speed flow part (b).

    83. Problem 4.38 The type of calculation in Problem 4.3 is a classic one for low-speed, incompressible flow, i.e., given the freestream pressure and velocity, and the velocity at some other point in the flow, calculate the pressure at that point. In a high-speed compressible flow, Mach number is more fundamental than velocity. Consider an airplane flying at Mach 0.7 at a standard altitude of 3 km. At a point on the wing, the airflow Mach number is 1.1. Calculate the pressure at this point. Assume an isentropic flow.

    85. Problem 4.39 Consider an airplane flying at a standard altitude of 25,000 ft at a velocity of 800 ft/sec. To experience the same dynamic pressure at sea level, how fast must the airplane be flying?

    87. Problem 4.40 In Section 4.9, we defined hypersonic flow as that flow where the Mach number is five or greater. Wind tunnels with a test section Mach number of five or greater are called hypersonic wind tunnels. From Eq. (4.88), the exit-to-throat area ratio for supersonic exit Mach numbers increases as the exit Mach number increases. For hypersonic Mach numbers, the exit-to-throat ratio becomes extremely large, so hypersonic wind tunnels are designed with long, high-expansion ratio nozzles.

    88. In this and the following problems, let us examine some special characteristics of hypersonic wind tunnels. Assume we wish to design a Mach 10 hypersonic wind tunnel using air as the test medium. We want the static pressure and temperature in the test stream to be that for a standard altitude of 55 km. Calculate: (a) the exit-to-throat area ratio, (b) the required reservoir pressure (in atm), and (c) the required reservoir temperature. Examine these results. What do they tell you about the special (and sometimes severe) operating requirements for a hypersonic wind tunnel.

    90. Problem 4.41 Calculate the exit velocity of the hypersonic tunnel in Problem 4.40.

    92. Problem 4.42 Let us double the exit Mach number of the tunnel in Problem 4.40 simply by adding a longer nozzle section with the requisite expansion ratio. Keep the reservoir properties the same as those in Problem 4.40. Then we have a Mach 20 wind tunnel, with test section pressure and temperature considerably lower than in Problem 4.40, i.e., the test section flow no longer corresponds to conditions at a standard altitude of 55 km. Be that as it may, we have at least doubled the Mach number of the tunnel.

    93. Calculate: (a) the exit-to-throat area ratio of the Mach 20 nozzle, (b) the exit velocity. Compare these values with those for the Mach 10 tunnel in Problems 4.40 and 4.41. What can you say about the differences? In particular, note the exit velocities for the Mach 10 and Mach 20 tunnels. You will see that they are not much different. What is then giving the big increase in exit Mach number?

More Related