1 / 41

Topic Discussion NFPA World Safety Conference & Exposition Minneapolis, MN May 19-23, 2002

An Overview of Commercial Transport Airplane Fuel Tank Inerting Research. William M Cavage Lead Engineer - Fuel Tank Inerting FAA AAR-440, Fire Safety R&D Branch. Topic Discussion NFPA World Safety Conference & Exposition Minneapolis, MN May 19-23, 2002. Outline. Background

christmas
Télécharger la présentation

Topic Discussion NFPA World Safety Conference & Exposition Minneapolis, MN May 19-23, 2002

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. An Overview of Commercial Transport Airplane Fuel Tank Inerting Research William M CavageLead Engineer - Fuel Tank Inerting FAA AAR-440, Fire Safety R&D Branch Topic DiscussionNFPA World SafetyConference & Exposition Minneapolis, MN May 19-23, 2002

  2. Outline • Background • Previous Research • Preliminary Research • Full-Scale Fuel Tank Inerting • Inert Gas Distribution Modeling • Onboard Inert Gas Generation AAR-422 Fire Safety R&D

  3. Background - Accident History • Three Accidents in Recent History • 1990: 737-300 - Manila, Philippines • 1996: 747-100 - New York, United States • 2001: 737-400 - Bangkok, Thailand (Investigation Pending) • All Accidents had Explosions in Center Wing-Tank • Explosions Occurred During/Just After Long Ground Operations on Hot Days with Empty (Residual Fuel) Center Wing Tanks • Exact Ignition Source Not Found During Any Investigation AAR-422 Fire Safety R&D

  4. Background - Recent Regulatory Activity • Inspections Required • 737, 747 Fuel Tank Wiring, 747 CWT Terminal Blocks, FQIS • Scavenge Pump Inspections, Related Equipment • Airworthiness Directives Issued • Various Fuel Pump Wiring/Connectors Inspect/Replace • Scavenge Pump and Surge Tank Flame Arrestor Installation • FQIS Wiring, Terminals, and Connectors Inspect/Replace • Special Addition to FARs (SFAR 88) • Requires Re-Validation of all Fuel Tank Safety Analysis for Existing Large Commercial Transport Category Airplanes • New Type Certificate Airplanes Must Minimize Flammability of Center-Wing Type Fuel Tanks to Be Equivalent to Wing Tanks AAR-422 Fire Safety R&D

  5. Background - Proposed Flammability Rule • FAA Issued Rule-Making Project Letter • Wrote Tasking Statement and Coordinated with JAA and ARAC and Published Notice in Federal Registry • ARAC Committee Formed Working Group • Congressionally Sanctioned Industry Oversight Committee that Advises FAA on Rulemaking • ARAC Working Group is made up of Industry Experts, Government Regulators, and Consumer Advocates • Focused on Analyzing Inerting Methods that could be Potentially Cost-Effective for the Commercial Fleet • Performed Extensive Cost Benefit Analysis • Report Pending Industry/Government Consensus AAR-422 Fire Safety R&D

  6. Previous Research - Methods • Macdonald and Wyeth - Fire and Explosion Protection of Fuel Tank Ullage, Circa 1950s • Compares Different Methods of Reducing Flammability including Nitrogen Inerting • Emphasized Requirements for Low Weight and Reliability • Klueg, McAdoo, and Neese - Performance of a DC-9 Aircraft Liquid Nitrogen Fuel Tank Inerting System, 1972 • FAA Developed and Tested an Inerting System Using Stored LN2 • System was Big, Heavy, and Required Extensive Ground Support • Yagle, et al. - Performance Tests of Two Inert Gas Generator Concepts for Airplane Fuel Tank Inerting, 1983 • Compared Pressure Swing Absorption (PSA) with Hollow Fiber Membrane (HFM) AAR-422 Fire Safety R&D

  7. Previous Research - Requirements • Stewart and Starkman - Inerting Conditions for Aircraft Fuel Tanks, 1955 • Most Comprehensive Work to Date on Flammability Limits and Oxygen Concentration Requirements • Pre-Dates JP-8 (Jet A) • Much of the Work is Theoretical with Limited Validation Points • Kuchta - Oxygen Dilution Requirements for Inerting Aircraft Fuel Tanks, 1970 • Presents Minimum Oxygen Requirements for CO2 and N2 From a Large body of Spark Ignition Data • No JP-8 Data (some Kerosene), Very Little Altitude Data AAR-422 Fire Safety R&D

  8. Previous Research - Requirements (cont’d) • Hill and Johnson - Investigation of Aircraft Fuel Tank Explosions and Nitrogen Inerting Requirements During Ground Fires, 1975 • Extensive Work on Ground Fires (Post Crash Scenarios) Causing Wing Fuel Tank Explosions • Largely Destructive Work had Older Test Articles AAR-422 Fire Safety R&D

  9. Preliminary Research • Ullage Washing Experiments (Inerting) • Quantitatively Determined Amount of Nitrogen Enriched Air (NEA) Required to Inert a Fuel Tank Test Article • Simple Rectangular Tank with Single Deposit Nozzle and Single Vent • Examined Different NEA % (Residual O2 Concentration) and Flow Rates as well as Examined Effects of Fuel Vapor and Temperature • Ullage Washing is Term Describing Inerting by Ventilation • Developed Nondimensional Relationships, Empirical Equation, and a Theoretical “Perfect Mixing” Solution • Data Illustrated that a VTE of 1.5 to 1.6 is Needed to Inert an Ullage to 8% Oxygen by Volume with 95% NEA (5% [O2]) • Published Report DOT/FAA/AR-01/6 AAR-422 Fire Safety R&D

  10. Rectangular Fuel Tank Inerting Data AAR-422 Fire Safety R&D

  11. Preliminary Research • Fuel Effects on an Inert Ullage • Quantitatively Determined the Effect an Unscrubbed Fuel Load Can Have on an Adjacent Inert Ullage • Simple Rectangular Tank with Single Deposit Nozzle and Single Vent • Examined Fuel Loads of 20, 40, 60, and 80 Percent Full at Sea Level and Two Altitudes; Inerted to 6, 8, and 10 Percent • Measured the Increase in Ullage [O2] due to Air Evolving from Fuel • Circulated the Ullage Through the Fuel to Bring Tank to Equilibrium Quickly - Represents Maximum Fuel Effect on Ullage • Study of Time Effects Showed Unless You Stimulate the Fuel, The Excess Air in Fuel had Small Effect on Ullage • Report Pending Publication AAR-422 Fire Safety R&D

  12. Inert Ullage Fuel Effects Data Max Increase in Ullage [O2] Due to Adjacent Fuel Load AAR-422 Fire Safety R&D

  13. Preliminary Research • GBI Proof of Concept Ground/Flight Testing • Joint Project with Boeing that Evaluated the Concept of Ground-Based Inerting • GBI is Inerting on Ground, Perform Ground Operations, and Fly • Examined the Effects of Wind and Flight Conditions on Ullage Oxygen Concentration of a model 737-700 • Inerted Tank with Ground Supplied NEA to Approximately 8% • Measured Oxygen Concentration at 8 Locations in CWT During “Normal” Ground and Flight Conditions • Testing Illustrated that the Benefit from Inerting was Substantial • Must Eliminate/Reduce CWT Cross Venting with Vent System Mod • Some Benefit Even With Small Fuel Loads • Published Report DOT/FAA/AR-01/63 AAR-422 Fire Safety R&D

  14. GBI Flight Test Data AAR-422 Fire Safety R&D

  15. Preliminary Research • Scale Boeing 747SP Tank Inerting • Quarter-Scale Model of Boeing 747SP CWT was Built from Three Quarter Inch Plywood By Scaling Drawings from Shepherd Report (24% Length Scale) • Variable Deposit Manifold Allowed for NEA to be Deposited at Any Rate in any Bay(s) Desired • Measured Oxygen Concentration in Each of the 6 Bays • Testing Illustrated that Equally Deposit NEA 95 will Allow for Comparable Results to the Simple Tank (VTE of 1.5-1.6 to 8%) • More Importantly, Uneven Deposit of Inert Gas Resulted in More Efficient Inerting (Less Gas to Inert the Same), Particularly when Half the Vent System Was Blocked • Published Report DOT/FAA/AR-02/51 AAR-422 Fire Safety R&D

  16. Boeing 747SP Scale CWT Model Inerting AAR-422 Fire Safety R&D

  17. Preliminary Research • Lower Oxygen Content Study • Performed Ignition Experiments with Model Fuel Tank in Pressure Chamber with both Propane and JP-8 at Reduced Oxygen Concentration • Tank Instrumented with Thermocouples and Sample Lines for Hydrocarbon and Oxygen Concentration Measurement. • Heaters Placed Underneath the Tank Control the Liquid Fuel Temperature (Flammability). • Used Single High Power Spark to Ensure a Reaction if Probable • Study at Sea Level and Altitude to 38K Feet • Follow on Tests Validated Previous Testing that the Critical Oxygen Concentration is Approximately 12% at Sea Level • Report Pending Publication AAR-422 Fire Safety R&D

  18. Lower Oxygen Content Study Data AAR-422 Fire Safety R&D

  19. Full-Scale Fuel Tank Inerting • Boeing 747SP Test Article • Decommissioned from Airline Service and Purchased by the FAA for Ground Testing Only • All Major Systems Fully Operational • Has Independent Power for Test Equipment and Instrumentation • Center-Wing Tank Fully Instrumented • Gas Sample Tubing for Oxygen and Total Hydrocarbon Analysis • 32 Thermocouples in Tank (Ullage, Fuel, Walls, Floor, and Ceiling) • Other Instrumentation • Additional Thermocouples in Pack Bay, NEA Deposit, Cabin etc. • 4 User Specified Oxygen Analysis Channels (Vent Channel, Dry Bay, etc.) • Some Weather Data Acquired • Full Complement of Ground Service Equipment AAR-422 Fire Safety R&D

  20. Boeing 747SP in Photo AAR-422 Fire Safety R&D

  21. 747SP Center Wing Tank Top Diagram AAR-422 Fire Safety R&D

  22. Full-Scale Fuel Tank Inerting • Validation of Assumptions / Localized Deposit • 747SP is Plumbed with a Single Deposit Manifold in Bay 3 Which was the Optimal Case (most efficient inerting), Developed from the Scale Tank Testing, with Half the Vent System Blocked • Inerted Tank with Different NEA Purities and Different Flow Rates in an Attempt to Validate Existing Knowledge Base and Assumptions • Limited Amount of Data to Date • Preliminary Data Shows Deposit Methodology and Modeling Work was Sound and Productive • Preliminary Data Looks Good as long as Mixing is Promoted by Operating the ACMs AAR-422 Fire Safety R&D

  23. 747SP Center Wing Tank Inerting Data AAR-422 Fire Safety R&D

  24. 747SP Center Wing Tank Inerting Data AAR-422 Fire Safety R&D

  25. Full-Scale Fuel Tank Inerting • Vertical Mixing / Temperature Effects • Quiescent Full-Scale Testing has Indicated that Inerting of the 747SP in the Optimal Deposit Method Developed with the Plywood Model can be Problematic (No ACMs Operating) • Inerting Efficiency Different from Test to Test • Measured Strong “Vertical Effects” in one Full Length Bay • Bottom of Bay [O2] Lags Behind Top of Bay on Quiescent Tests • Complicated by the Fact that Sample System only Samples from Top • Preliminary Data Shows Effect is Not NEA Temperature Dependant but is Effected by the NEA Temperature • Developed Inerting Efficiency Coefficient to Compare Tests • Back Calculate VTEs between 1.2 and 2.0 to reach 8% [O2] with 95% NEA AAR-422 Fire Safety R&D

  26. 747SP Inerting Data with Different Vertical Mixing AAR-422 Fire Safety R&D

  27. 747SP Calculated Inerting Curves with Different Vertical Mixing AAR-422 Fire Safety R&D

  28. Inert Gas Distribution Modeling • Preliminary Models • Original Simple Inerting Model Developed by Ivor Thomas (FAA CSTA for Fuel Systems) • Tracks the Volume of Oxygen In and Out of a Tank and Calculates Oxygen Concentration Given the Tank Volume • Uses a Basic Spreadsheet Layout and Runs Instantaneously Given the Volume of the Tank, The Flow Rate and Purity of the NEA • Basic Formula for Model • Model Results Compared Well with Ullage Washing Data AAR-422 Fire Safety R&D

  29. Simple Inerting Model Results Compared with Ullage Washing Data AAR-422 Fire Safety R&D

  30. Inert Gas Distribution Modeling • Scale CWT Model • Original Plywood Model Results Encouraging, But NEA Distribution Did Not Compare Well with Full-Scale Data • Made Several Improvements to Model • Better Modeling of Vent System Cross Sectional Flow Areas • Ensured Lid Did Not Leak Around Bay Tops which Would Alter Flow Pattern • Performed Additional Testing • Scale Tank Inert Gas Distribution Results Compared Very Well to Data Acquired on 747SP full-scale test article • Additional Testing Planned for Different Deposit Methods (Onboard System) AAR-422 Fire Safety R&D

  31. Scale Plywood CWT Model AAR-422 Fire Safety R&D

  32. Scale Plywood CWT Model Data Comparison AAR-422 Fire Safety R&D

  33. Inerting Model Development • Multiple-Bay Inerting Engineering Model • Model Calculates Inert Gas Distribution in 6 Bay Tank, in terms of Oxygen Concentration Evolution, Given NEA Purity and Bay Deposit Flow Rates • Based on Original Inerting Model by Ivor Thomas which Tracks Oxygen In and Out of Each Bay Assuming Perfect Mixing During the Time Step • Assumes an “Outward” Flow Pattern and Splits Flow into a Bay to Adjacent Bays Using Out Flow Area Relationships • Presently Does Half Blocked Venting Case Only • Compared with Full-Scale Test Article • Must Run ACMs to Obtain Data that Agrees with Engineering Model (Which Assumes Perfect Mixing) • Agrees Best for Single Deposit Case Compared with Scale Tank Data AAR-422 Fire Safety R&D

  34. Engineering Model Assumed Flow Pattern Bay 1 Flow Out Bay 2 Flow In Bay 3 Bay 4 Bay 5 Bay 6 Flow Out AAR-422 Fire Safety R&D

  35. Engineering Model Data Comparison AAR-422 Fire Safety R&D

  36. Full-Scale Data Compared with Modeling Methods AAR-422 Fire Safety R&D

  37. Onboard Inert Gas Generation System • Popular Methods of Generating NEA or N2 • Pressure Swing Absorption (PSA) • System Pressurizes a Separation Bed with Air and Allows to Dwell • Can Generate High Purity N2 and O2 (OBIGGs/OBOGs) • Systems can be Designed to Have High Output Volumes • Needs High Pressure Bleed Air / Many Complex Moving Parts • Hollow Fiber Membrane Gas Separation • Hollow Polymeric Membranes Are Wove and Bundled in Canisters -Pressurized Bundle Ends Separates Fast and Slow Gases in Air • Can Operate at Low Pressures and Systems Have very Few Moving Parts • Can Not Generate O2, Inefficient at Producing NEA above 99% Nitrogen • Distillation / Cryogenic • New Technology Allows for Small Scale Liquefaction of Air Components • Low Output so Storage is Needed AAR-422 Fire Safety R&D

  38. Onboard Inert Gas Generation System • Commercial Transport Onboard System Development • Optimized a System for Inerting Boeing 747SP CWT on Ground • System Designed to Inert Empty CWT below 12% in less then 90 Minutes with Compressor. Can Inert in Half that time with Bleed Air • System Installed in Pack Bay Area with Crashworthy Mounting • System Weight Approx. 240 lbs Plus Deposit Plumbing and Vent Modification • System Designed to Provide Some Cargo Bay Fire Protection • Replace a Bleed System for 747SP • Specified all Airworthy, Commercially Available Parts • Some Parts will be for Ground Test Only • Compressor is Modification of Existing Design AAR-422 Fire Safety R&D

  39. OBGI System Block Diagram AAR-422 Fire Safety R&D

  40. 3-D Rendering of System Installation AAR-422 Fire Safety R&D

  41. Closing Remarks • Addition Information • Contact Me @ AAR-440 Fire Safety Branch, Building 204 Wm. J Hughes Technical Center Atlantic City Int’l Airport, NJ 08405 (609) 485 - 4993 william.m.cavage@faa.gov • Fire Safety Web Site @ www.fire.tc.faa.gov • Inerting Work is Under Systems Fire Group / Fuel Tank Safety • More Information on Projects and Facilities • Download Reports and Presentations (Including This One!!!) • International Systems Fire Protection Working Group • Open Forum to Discuss FAA/Industry R&D in Area of Aviation Fire Protection (Including Fuel Tank Safety) - Register on Web Site AAR-422 Fire Safety R&D

More Related