1 / 10

DIT314 ~ Client Operating System & Administration

DIT314 ~ Client Operating System & Administration. CHAPTER 4 CONFIGURING HARDWARE DEVICES AND STARTUP PROCESS Prepared By : Suraya Alias. 4.5 THE STARTUP PROCESS. 4.5.1 Startup Phases (sequences) Power-on self test (POST) phase Initial startup phase Boot loader phase

denali
Télécharger la présentation

DIT314 ~ Client Operating System & Administration

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DIT314 ~ Client Operating System & Administration CHAPTER 4 CONFIGURING HARDWARE DEVICES AND STARTUP PROCESS Prepared By : Suraya Alias

  2. 4.5 THE STARTUP PROCESS • 4.5.1 Startup Phases (sequences) • Power-on self test (POST) phase • Initial startup phase • Boot loader phase • Detect and configure hardware phase • Kernel loading phase • Logon phase • This sequences applies only to the system that was shut down ad restarted normally, not applicable for hibernation and standby mode

  3. 4.5 THE STARTUP PROCESS • For Win XP to start, the systems and boot partitions must contain below files

  4. 4.5 THE STARTUP PROCESS • 4.5.2 Preboot sequences • Computer runs POST routines to determine the amount of physical memory, whether the hardware component are presents. Check plug and play compatible BIOS and hardware configuration • The comp BIOS locates the boot device, loads and runs the Master Boot Record (MBR) • The MBR scans the partition table to locate the active partition, loads the boot sector on the active partition in memory the executes it • The computer loads and initializes the NTLDR file

  5. 4.5 THE STARTUP PROCESS • Problem that can occur during Preboot sequences • Improper hardware configuration or malfunctioning hardware • Usually message hard drive cannot be located • Corrupt MBR • If MBR becomes corrupted (virus), can be repaired back using Recovery console or using Anti virus s/w • Floppy or USB inserted • Message non system disk or disk error, or No OS is found, maybe USB is inserted during startup

  6. 4.5 THE STARTUP PROCESS • 4.5.3 Boot sequences • After NTLDR has been loaded into memory, the boot sequence gathers information about the hardware and drivers in the preparation for Win XP load phases. • The boot sequences uses these files; NTLDR, BOOT.INI, BOOTSECT.DOS (optional), NTDETECT.COM & NTOSKRNL.EXE • The 4 phases of boot sequences • Initial boot loader phase • Operating System Selection • Hardware Detection • Configuration Selection

  7. 4.5 THE STARTUP PROCESS • 4.5.4 BOOT.INI file • Boot.ini is saved in active partition when we install Win XP. • NTLDR uses information in boot.ini to display the boot loader screen, from which you select the OS to start. • Boot.ini includes two section [boot loader] and [operating system] which contains information that NTLDR uses to create the Boot Loader Operating System Selection menu • Example [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(2)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Microsoft Windows XP Professional" /fastdetect multi(0)disk(0)rdisk(0)partition(2)\WINNT="Windows 2000 Professional" /fastdetect

  8. 4.5 THE STARTUP PROCESS • 4.5.5 Troubleshooting the Boot Sequence (Problem) • Missing or corrupt boot files • If the NTLDR, BOOT.INI, NTDETECT.COM & NTOSKRNL.EXE files become corrupt or missing, the error message indicating the situation and windows startup fails • Improperly configured BOOT.INI • If manually edited, or change the configuration. If BOOT.ini corrupt, use the Recover console • Improperly configured hardware • NTDETECT.COM cab fail during its detection of hardware if the h/w is wrongly configured, bad driver or malfunctions • Use step by step of removal, uninstalling the devices and adding it one by one at a time

  9. 4.6 EDITING THE REGISTRY • Win XP stores hardware and software settings in a hierarchical database called the Registry (replaces the .ini, .sys and .com configuration in previous windows) • Registry controls the Win XP OS by providing information in starting applications, load components and devices also network protocols • 4.6.1 Registry • Hierarchical database that contains data includes; • The hardware installed in computer (cpu, bus type..) • Installed device drivers • Installed applications • Installed network protocols • Network adapter card settings

  10. 4.6 EDITING THE REGISTRY • Components that access and store data in registry • Windows XP Pro kernel • Device drivers • User profiles • Setup programs • Hardware Profiles • NTDETECT.COM

More Related