1 / 21

DHP Re-Calibration

DHP Re-Calibration. Moving to Uo -based Calibration (away from Thermostat-based Calibration) Regional Technical Forum May 13, 2014. Phase I Adjustment to SEEM Output to Match Bills (for Houses with “well-known” Heating Energy Use). Background: DHP Calibration.

dolph
Télécharger la présentation

DHP Re-Calibration

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DHP Re-Calibration Moving to Uo-based Calibration (away from Thermostat-based Calibration) Regional Technical Forum May 13, 2014

  2. Phase IAdjustment to SEEM Output to Match Bills(for Houses with “well-known” Heating Energy Use)

  3. Background: DHP Calibration • Existing DHP Phase I Calibration, approved in July 2013, is based on the old Thermostat Setting calibration method:

  4. Goal: Determine Uo-based Phase I Calibration Factors for DHPs

  5. Methodology • Use DHP Metering Study data (n=95 pre billing, post metering) to interpolate between the Zonal/eFAF and HP/gFAF calibration factors. • See the following for more details: • “DHPphaseIcalibrationMemo” document • “DHP_SEEM_calibration_PhaseI” workbook • Two equally legitimate methods of interpolating, both give slightly different answers • Average of Interpolations (=0.60) • Interpolation of Averages (=0.55)

  6. Comparison “Interpolation of Averages”, or =0.55, was selected since it results in overall savings closer to the original for the DHP UES measures.

  7. Proposed Calibration Factors(DHP in Green)

  8. Decision • “I _____ move that the RTF adopt the revised Uo-based Phase I calibration adjustment factors for DHP’s.”

  9. Phase IIAdjustment to Electric Energy Use for Non-electric Fuel usage, Unoccupied Houses, and houses with otherwise misbehaved bills

  10. Background • Phase II Adjustments: • For program-like houses (permanent electric heat, no non-electric FAF or boiler), the adjustments address: • Non-utility heating sources, • Program-permitted gas heat sources (e.g., gas fireplaces), and • Other SEEM Phase I calibration filters • See September 2013 RTF meeting presentation for more details Today’s Goal: Determine values for DHP.

  11. Available Data Source: DHP Pilot Study, R2≥0.45 Source: RBSA SF, Zonal Electric Source: SEEM runs, Phase I applied

  12. Two UES Analysis Methods • The next two slides show the two methods in detail. • The difference between the two methods (in words): • S1 uses the ratio of savings from the average house to non-supplemental fuel houses. • S2 uses the ratio of energy use from the average house to non-supplemental fuel houses. • Q: Which one’s better, correct? • Theyseem to offer the same correctness. • S2 aligns better with our guidelines: Determines baseline and efficient case consumptions separately. • The S2 Method will allow us to generate Phase II calibration factors for DHP’s (The S1 Method will not). • The S2 Method aligns with our need to assign a separate “wood heat” adjustment factor to DHP’s. • But they give different answers (especially in HZ3): • Whether we should revisit the DHP UES is out of scope for this presentation.

  13. Background: DHP UES Savings Methodology

  14. Background: DHP UES Alternative Methodology

  15. Proposed Methodology We continue to have no fully satisfying solution. Supplemental fuels use has been a difficult thing to pin down; it still requires a fair amount of judgment for DHP’s.

  16. Step 1 – Apply implied adjustment to DHP • Remember there’s a component of the adjustments that represents unoccupied houses and houses with otherwise misbehaved bills. • We’ll assume DHP houses, on average, have the same results as other heating systems (which are based on RBSA data).

  17. Step 2 – Re-state Known Adjustments • The DHP Pilot data and UES savings methodology does not make adjustments for unoccupied houses or houses with misbehaved bills • We’ll re-calculate the “eFAF, Zonal, HP, or Gas FAF” electric heating adjustments without the implied adjustment: • This is R2.Z from the alternative method above (S2 method), but using RBSA specific data, rather than DHP Pilot data.

  18. Step 3 – Find R2.D(RBSA) by using S2 from the DHP UES alternate analysis. Solve for R2.D(RBSA)

  19. Step 4 – Work backward to fill in the blanks. Negative value doesn’t make sense, we’ll need to fix that.

  20. Step 5 – Re-assign negative value in HZ3. Again, not a completely satisfying solution, but it doesn’t affect savings too much: S2 for HZ3 changes from 970 kWh/yr to 1,043 kWh/yr with this “tweak”.

  21. Decision • “I _____ move that the RTF adopt the Phase II calibration adjustment factors for DHP’s.”

More Related