1 / 66

Repair, relining and rebasing

Repair, relining and rebasing. Dr. Amal Fathy Kaddah Professor of Prosthodontic, Faculty of Oral &Dental Medicine, Cairo University www.egydental.com. First Steps In Making A Denture. Primary impression Diagnostic cast Custom tray Final impression Master cast. Impression Techniques.

ebranham
Télécharger la présentation

Repair, relining and rebasing

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Repair, relining and rebasing Dr. Amal Fathy Kaddah Professor of Prosthodontic, Faculty of Oral &Dental Medicine, Cairo University www.egydental.com

  2. First Steps In Making A Denture • Primary impression • Diagnostic cast • Custom tray • Final impression • Master cast

  3. Impression Techniques • Primary impressions Conventional techniques Template techniques • Definitive impressions I- Conventional techniques II- Selective pressure techniques III- Functional techniques IV- Reline and rebase techniques (including secondary template impressions).

  4. Complete Dentures

  5. Repair of Complete Dentures

  6. Dentures may fracture during function dropped on hard surface Key of repair = accurate reassembling & alignment of the broken parts in their original position.

  7. Classification of fractured dentures I) According to location of fracture Midline fracture Any part fracture

  8. II) According to extentof fracture Without broken or missing part &/or teeth With broken or missing part &/or teeth

  9. III) According to timing of fracture Early fracture Delayed fracture • IV) According to cause of fracture • Operator Patient

  10. Midline fracture (mainly in maxillary dentures) Causes: 1) No or insufficient relief in the midline. (M.P.R.) (Early fracture) 2) Ridge resorption with loss of relief effect. (Delayed fracture)

  11. Procedures for repair of midline fracture: • Broken parts are assembled & fixed together with sticky wax on the polished surface. • Assembled parts may be strengthened with burs or plastic sticks.

  12. Procedures for repair of midline fracture: • Any undercut on the fitting surface is blocked out with wax or clay. • The fitting surface is painted with separating medium.

  13. Stone plaster is poured into the fitting surface. After stone setting, the denture is removed from the cast and cleaned from any traces of sticky wax. • Fractured edges are reduced, widened (8-10 mm) along the fracture line and beveled towards the polished surface to increase bonding surface area. • Dove tail cuts may be made to strengthen the repair joint.

  14. The cast is painted with separating medium and the denture is secured to the cast with rubber bands. • Self cure A.R. is applied to the modified fracture area until the area is overfilled. • N.B. An alternate method is to wax and contour the fracture line to the desired form using base plate wax, followed by flasking, wax elimination, packing with self cure A.R. and placing in the flask under press for 2 hrs. • Deflasking, finishing and polishing is then done in the usual manner.

  15. Relief of the median palatine raphea. • Reline if needed. • Remake in some cases.

  16. Any part fracture Main causeis falling on the ground or the sink during cleaning. Types: I- Fracture with no missing part Repaired as mentioned.

  17. II- Fracture with missing or lost part Procedures: • An impression is made with the denture placed in patient mouth. • After pouring the cast, either self cure A.R. is applied to replace the missing part, or wax is added and carved to resemble the broken denture part, followed by flasking, packing, curing, finishing & polishing.

  18. III- Fracture with broken or missing teeth Procedures: • Fractured teeth are cut away with burs. • On the lingual side, enough acrylic is removed and dove tailed. • Teeth of same size, shape & shade are positioned in proper alignment and waxed with base plate wax.

  19. A plaster index (key) is made to record & secure the position of waxed teeth. • Teeth to be repaired are removed together with all wax around them. • Teeth are then put back exactly in their original position aided by plaster key. • Self cure acrylic resin is added from the lingual side until repair area is over built. It is then covered with tin foil. • After curing, the index is removed and the denture is finished and polished.

  20. Relining of Complete Dentures Def:Resurfacing or correction of denture adaptation to underlying tissues by the addition of a new resin material to its fitting surface without changing its occlusal relation. Addition of Material to the tissue side of a denture to improve its adaptation to the supporting mucosa.

  21. Reline Indications Whenever the denture loses or has poor adaptation to the underlying tissues, while all other factors asocclusion, esthetics, centric relation, V.D.O. and denture base material are satisfactory. • Loss of retention • Instability • Food under denture • Abused mucosa

  22. Reline: General Considerations • Optimal tissue health • Reasonable CR/CO • Adequate vertical dimension • Adequate peripheral extensions

  23. Procedures: • Patient is instructed to leave his denture out of his mouth at least 48 hrs to allow for recovery of tissues and reduce irritation caused by ill-fitted denture. • Denture preparation: • Any undercuts are removed from the denture base. • Peripheral extensions are checked and adjusted. • Borders are reduced and squared to provide a definite edge for addition of new resin material.

  24. A hole is made in the palatal surface to allow escape of excess impression material. Slight reduction in the fitting surface may be done to create some space for the impression material. • Border tracing & new impressions are made under centric occlusion to maintain occlusal relationship. • The denture with impression material is boxed and poured into stone.

  25. . The denture is flasked, and the old resin material is thoroughly cleaned and roughened.

  26. . New acrylic resin material is packed, and the denture is cured in pressure curing unit containing water at 45°c for 20 min. to prevent porosity of new resin materialand warpage of the old resin material (release of internal stresses). . Finishing and polishing is done in the usual manner.

  27. N.B. When both upper and lower dentures need relining, lower denture should be completed first. The upper may be relined against a stable lower denture. The denture should be clinically remounted to perfect the occlusion.

  28. Evaluate Dentures

  29. Is Reline necessary???? If after modifications, the “fit and bite” seem improved, let the patient try the denture for one week…if there is no improvement, then reline.

  30. Is reline Necessary? Overextension Irritation of Peripheral Borders

  31. Is reline Necessary? Overextended borders Borders corrected

  32. Is reline necessary? Error in CO on one side, will break the seal on the opposite side

  33. Is reline necessary? Correct eccentric excursions

  34. Diagnosis-Occlusal disharmony • Loss of stability and retention • Irritation and inflammation on one side • Teeth stained on one side

  35. Reline Contraindications • Worn out dentures • Vertical dimension loss greater than 7 mm • Significant mucosal inflammation • Poor denture esthetics • Denture related speech problems

  36. Contraindications • Severe tooth wear • Severe vertical overlap with tooth wear (posterior tooth concept) • Severe occlusal wear (CD evaluation)

  37. Pre-requisites for relining Recognition of abused tissues, with superimposed candidiasis.

  38. Initiate Tissue Recovery Program • Intermittent hot and cold rinses • Massage tissues • Relieve pressure areas • Correct faulty occlusions and denture borders • Minimize stress by • Soft diet • Removal of denture at night • Use tissue conditioners

  39. Complete Denture Exam • Healthy Tissues!!

  40. CUD Reline 2. Indicate amount of peripheral reduction required 1. Check extensions 3. Border Reduction 4. Tissue Conditioner preparation: Peripheral reduction + Tissue surface

  41. CUD Reline 5. Border Molding Completed 6. Palatal surface vented after B. M. 7. Seat denture until wash comes through vents 8. Final Impression

  42. CUD Reline • Incorrect seating. Improper plane of orientation: • Not contacting teeth • Excess material • No vents • Place ZnO wash • Have patient close in CR.

  43. CUD Reline Trim excess wax beyond anterior line ZnO wash. Posterior palatal seal area using impression wax Reline final impression

  44. Final Impression with PVS Final Impression with Rubber base

  45. post palatal seal combination • Identify in impression, before pouring it up. • Identify on impression so technician can scribe the seal

  46. CLD Reline Complete Denture method-ZnO Border molding completed Rubber Base Reline

  47. Reline Roughened border to blend new acrylic with old. Won’t show finishing line After processing: Note junction line Relined cast: Do not separate

  48. Reline Trimmed and polished

  49. Delivery of Reline • Examine: • Peripheral extensions

  50. Delivery of Reline • Pressure Indicator Paste (PIP) • Ask the patient to bite on cotton rolls for 5 min.

More Related