1 / 20

Manual handling is associated with

Manual handling is associated with. 27% of all industrial injuries 670,000 injuries/yr in the United States 60% of all money spent on industrial injuries 93,000,000 lost workdays/yr. Approaches to recommendations. Biomechanical emphasizes forces and torques

guy-atkinson
Télécharger la présentation

Manual handling is associated with

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Manual handling is associated with • 27% of all industrial injuries • 670,000 injuries/yr in the United States • 60% of all money spent on industrial injuries • 93,000,000 lost workdays/yr

  2. Approaches to recommendations • Biomechanical • emphasizes forces and torques • load limit does not vary with frequency • Physiological • emphasizes energy requirements and cardiovascular demands • important for repetitive lifting • Psychophysical • combination of the above • predicts “real” capability based on performance under controlled conditions

  3. Manual handling variables • Individual • Technique • Task • Goals: • increase the strength of the worker • decrease the stress due to technique and task • both

  4. Pushing and pulling strength factors • Handles • One hand vs. two hands • Body posture • Application height • Direction

  5. Push/pull summary • Two hands are usually better than one. • Force capability goes down as it is exerted more often. • Initial force capability is higher than sustained capability. • Pushing capability is higher than pulling. • Push at waist level; pull at thigh level.

  6. Task modifications • Measure the force required to move all wheeled equipment; periodically check the forces. • Install vertical push/pull bars on carts. • Push rather than pull loads. • Avoid muscle-powered pushing and pulling for ramps, long distances, and frequent moves. • Use mechanical aids and momentum. • Reduce force by reducing friction.

  7. Holding • Problems • Holding gives a static load combining body weight and object weight. • Low-back pain arises from spine biomechanics. • Solutions • Reduce the magnitude and duration of the torque. • Use balancers. • Limit high loads to short durations.

  8. Carrying guidelines • Replace carrying with pushing or pulling. • Minimize the moment arm of the load relative to the spine. • Consider carrying large loads occasionally rather than light loads often. • Use teamwork. • Consider using balancers, manipulators, conveyors, or robots. • Reduce lifting by raising the initial location. • Avoid carrying objects up and down stairs.

  9. Lifting guidelines • 51 lbs is the maximum that can be lifted or lowered (load constant). • Recommended weight limit (RWL) is load constant multiplied by various factors. • Lifting index = load weight / RWL

  10. NIOSH lifting example • At initiation, • Horizontal location, H1 = 10 in. • Vertical location, V1 = 40 in. • Vertical location, V2 = 51 in. • Angle of asymmetry, A = 0 • Frequency, F = 12 /min. • Load = 14 lbs. • Duration = 2 hr. • What is the RWL? • What is the Lifting Index, LI?

  11. Basic NIOSH lifting formula (pg. 253) RWL = LC × HM × VM × DM × FM × AM × CM • RWL = recommended weight limit • LC = load constant (51 lbs.) • HM = horizontal multiplier • VM = vertical multiplier • DM = distance multiplier • FM = frequency multiplier • AM = asymmetry multiplier • CM = coupling multiplier Note: review the conditions under which this will not apply – turned around, they make a good set of criteria for lifting task design!

  12. Multiplier formulas Horizontal multiplier HM = BIL / H • BIL = Body interference limit • H = Horizontal location Vertical multiplier VM = 1 – VC × | V – KH | • VC = Vertical constant = 0.0075for inches, 0.003 for cm. • V = Vertical location • KH = Knuckle height (assume 30 in.)

  13. Multiplier formulas (cont.) Distance multiplier DM = .82 + DC/D • DC = Distance constant = 1.8 for inches, 4.5 for cm. • D = Vertical travel distance Asymmetry multiplier AM = 1 – .0032A • A = Angle of symmetry

  14. Multiplier formulas (cont.) Frequency multiplier See Table 13.9, pg. 255. • Lifting frequency = mean number of lifts in a 15-minute period • Lifting duration /session in hours may be: • Short = .001 h to ≤ 1 h • with recovery time of ≥ 1.2 × duration • Moderate = >1 h ≤ 2 h • with recovery time of ≥ .3 × duration • Long = >2 h but ≤ 8 h

  15. Multiplier formulas (cont.) Coupling multiplier See Table 13.10, 13.11, Fig. 13.13 • Depends on: • Height of initial and final hand–container coupling • Whether coupling is good, fair, or poor

  16. Solution … • HM = • VM = • DM = • FM = • AM = • CM = • RWL = • LI =

  17. Force limits FL = A × F × DIST • A = Age factor • F = Frequency factor • DIST = Distance factor • Differences between force limits and NIOSH guidelines. • Different factors • Different criteria • FL permissible load ~1.8 times that of NIOSH

  18. Resources • Manual Handing Guide (Mital et al.) • Biomechanical software • ErgoIntelligence MMH • 2D Static Strength Prediction Program • 3D Static Strength Prediction Program

  19. Guidelines for manual handling • Three categories: • Select individual • Select strong people based on tests. • Teach technique • Bend the knees. • Don’t slip or jerk. • Don’t twist during the move. • Design the job • Use machines. • Move small weights often. • Get a good grip. • Put a compact load in a convenient container. • Keep the load close to the body. • Work at knuckle height.

  20. Examples to discuss

More Related