1 / 12

Buck Regulator Architectures

Buck Regulator Architectures. 4.1 Overview. LM22676. LM3102. LM2747. LM3489. Buck-Switching Converters. Synchronous . Non-Synchronous . (Internal-FET) Regulators. (External-FET) Controllers. Non-Synchronous Buck Converters. L. S. Is. IL. +. Io. Id. Ic. C. Vin. D. Vout. -.

jadyn
Télécharger la présentation

Buck Regulator Architectures

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Buck Regulator Architectures 4.1 Overview

  2. LM22676 LM3102 LM2747 LM3489 Buck-Switching Converters Synchronous Non-Synchronous (Internal-FET) Regulators (External-FET) Controllers

  3. Non-Synchronous Buck Converters L S Is IL + Io Id Ic C Vin D Vout - ΔIL, Ton = ΔIL, Toff Vout = D*Vin ΔIL, Ton = (Vin – Vout ) * Ton / L D = Ton / (Toff +Ton) ΔIL, Toff = -Vout * Toff/ L

  4. Buck Topology: Current and Voltage Waveforms Input current Low side switch or diode Output and Inductor Switch

  5. Light-Load Operation: CCM and DCM D = VOUT/VIN Full Synchronous Mode. Stays in Continuous Conduction Mode (CCM) t Inductor current reverses polarity at light loads D ≠ VOUT/VIN Diode or Diode Emulation t Inductor current drops to zero before the end of the cycle: “Discontinuous Conduction Mode” (DCM)

  6. Cross Conduction with Synchronous Buck • Direct Connection between VIN and Ground • High – Side and Low – Side must not be in ON state at the same time • A time in which both MOSFET are Turned OFF is required: DEAD - TIME

  7. DEAD – TIME • FIXED DEAD – TIME • Fixed time between Turn-OFF and Turn-ON • No flexibility in MOSFET choice • ADAPTATIVE DEAD – TIME • High-Side turns ON only if LS is OFF and vice versa • Full flexibility in MOSFET choice • It is necessary to detect the Turn-OFF of both MOSFET

  8. Control Mode • Voltage Mode Control (VMC) • Current Mode Control (CMC) • Peak Current Mode Control (PCMC) • Valley Current Mode Control (VCMC) • Average Current Mode Control (ACMC) • Hysteretic Mode Control (HMC)

  9. Voltage Mode ControlAdvantages and Disadvantages • Advantages • Stable modulation/less sensitive to noise • Single feedback path • Can work over a wide range of duty cycles • Disadvantages • Loop gain proportional to VIN • LC double pole often drives Type III compensation • CCM and DCM differences - a compensation challenge • Slow response to input voltage changes • Current limiting must be done separately

  10. Current Mode ControlAdvantages and Disadvantages • Advantages • Power plant gain offers a single-pole roll-off • Line rejection • Cycle-by-cycle current limiting protection • Current sharing • Disadvantages • Noise • Minimum ON-time • Sense resistor

  11. Hysteretic Mode ControlAdvantages and Disadvantages • Advantages • Ultra fast transient response (preferred to use in power hungry load) • No phase compensation required; In other words, Hysteretic Mode is a kind of large signal control • Disadvantages • Noise Jitter susceptible • Very layout sensitive • Large switching frequency variation; Minimum ripple requirement

  12. Thank you!

More Related