1 / 29

EEE107J1

EEE107J1. Internal Resistance of a Voltage Source. Ideal voltage source – no internal resistance. R int = internal resistance of source. No Load Voltage. Load Voltage. after Boylestad. Find V L and power loss in R int. after Boylestad. Voltage Regulation. after Boylestad.

jaser
Télécharger la présentation

EEE107J1

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. EEE107J1

  2. Internal Resistance of a Voltage Source Ideal voltage source – no internal resistance Rint = internal resistance of source No Load Voltage Load Voltage after Boylestad

  3. Find VL and power loss in Rint after Boylestad

  4. Voltage Regulation. after Boylestad

  5. Identical resistors in parallel If all the resistances have equal value then after Boylestad

  6. Four parallel resistors of equal value. after Boylestad

  7. Calculate RT, IS, I1,I2, Power in each resistor and total power dissipated after Boylestad

  8. Determine R3, E, Is, I2, after Boylestad

  9. Using Kirchoff’s current law Find I5 after Boylestad

  10. Find I3 and I7 after Boylestad

  11. Current division. For two parallel elements of equal value the current will divide equally For parallel elements with different values the smaller the resistance, the greater the share of input current. For parallel elements of different values, the current will split with a ratio equal to the inverse of their resistor values after Boylestad

  12. Current divider rule for two resistors in parallel after Boylestad

  13. Calculate the current through each resistor after Boylestad

  14. Determine I1 and I2 I2could be found by the application of the current rule after Boylestad

  15. Determine R1 Use KCL Now use Ohm’s law to find VR2 VR2 = VR1 i.e. Ohm’s law

  16. Demonstrating the characteristics of an open circuit. after Boylestad

  17. Demonstrating the effect of a short circuit on current levels. after Boylestad

  18. Branch current analysis This is a means of analysing a network by the application of Kirchhoff’s laws to linear networks Basically follow the following steps • Assign a distinct current of arbitrary direction to each branch of the network. • Indicate the polarities for each resistor as determined by the assumed current directions • Apply Kirchhoff’s voltage law around each closed independent loop of the network

  19. B A C F E D Assign currents I1, I2, and I3Note I1+I2=I3 Assign letters/identification to network

  20. A B C F D E Insert the polarities across the resistive elements as defined by the chosen branch currents.

  21. Apply KVL to each loop ABEF 2 = 2I1 + 4I3 BCDE 6 = 1I2 + 4I3 OR 2 = 2I1 + 4I1 + 4I2 OR 6 = 1I2 + 4I1 + 4I2

  22. ABEF 2 = 2I1 + 4I3 BCDE 6 = 1I2 + 4I3 OR 2 = 2I1 + 4I1 + 4I2 OR 6 = 1I2 + 4I1 + 4I2 It should be clear that the equations on the right have only two unknown currents I1 and I2. Combining terms in this set of equations gives ABEF 2 = 2I1 + 4I1 + 4I2 gives 2 = 6I1+4I2 BCDE 6 = 1I2 + 4I1 + 4I2 gives 6 = 4I1+5I2

  23. ABEF 2 = 6I1+ 4I2 BCDE 6 = 4I1+ 5I2 multiplying ABEF by 2. gives multiplying BCDE by 3 gives ABEF 4 = 12I1+ 8I2 BCDE 18 = 12I1+15I2 Subtracting BCDE from ABEF gives -14 = -7I2 thus I2 = 2A Substituting I2 = 2A back into the equation for loop ABEF 2=6I1+8 ABEF 2 =6I1+4I2 Thus I1=-1A note the current is minus and thus flows in the opposite direction to that originally assigned

  24. Reviewing the results of the analysis of the network

  25. Calculate V1 and V2 assume that IB = 0A Determine the voltage VE and current IE Determine VRCassuming IC = IE Calculate VCE 25

  26. Calculate V1 and V2 assume that IB = 0A Apply voltage divider rule to R1 R2 Apply KVL to find V1 22V = V1 + V2 = V1 + 2V V1 = 20V after Boylestad 26

  27. V1 = 20V , V2 = 2V Determine the voltage VE and current IE Apply KVL to base circuit as below 27

  28. V1 = 20V , V2 = 2V Determine the voltage VE and current IE Apply KVL to base circuit as below In this loop V2 + VBE + VE = 0V Apply potentials and polarities after Boylestad 28

  29. V1 = 20V , V2 = 2V, VE = 1.3V, IE = 1.3mA. Calculate VRC Determine VRC assuming IC = IE after Boylestad 29

More Related