1 / 16

Adhesives Questions

Adhesives Questions. 1)What is the best kind of clamp to use when gluing wood edge to edge? Spring clamp Bar clamp C clamp Hand screw clamp. 2)When clamping with bar clamps, make sure you:. A) Place them all on the bottom B) Alternate the clamps top to bottom C) Space them 2 inches apart

jasper
Télécharger la présentation

Adhesives Questions

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Adhesives Questions 1)What is the best kind of clamp to use when gluing wood edge to edge? Spring clamp Bar clamp C clamp Hand screw clamp

  2. 2)When clamping with bar clamps,make sure you: • A) Place them all on the bottom • B) Alternate the clamps top to bottom • C) Space them 2 inches apart • D) Rotate the outside ones 90 degrees

  3. 3. When gluing solid stock edge to edge: • A) hold it in place with spring clamps. • B) place the sap wood to the outside. • C) Alternate the growth rings. • D) Place the growth rings all the same direction.

  4. Excess glue • What should be done with excess glue before planing? • A. Removed with a glue scraper. • B. Left so the planer can remove it. • C. Sanded off. • D. Removed with lacquer thinner.

  5. Set up time • How Long should the wood remain in the clamps? • A) Three hours • B) two days • C) Nine hours • D) Thirty minutes

  6. How long do you need to wait before planing, etc.? 24 hrs. 15 minutes 1 hour 45 minutes

  7. What do you do about glue that gets on a finished surface of your project? • A)Remove it with paint thinner • B) file it off • C) color it with finish putty • D) scrub it off as soon as possible with a wet sponge or rag

  8. What type of adhesive is used to bond plastic laminate to a wood substrate? • A) contact cement • B) hide glue • C) yellow glue • D) super glue

  9. Contact cement How can you apply the contact cement? A) Sprinkle it on B) Pour it on C) Brush, roll, or spray it on D) Iron it on

  10. To which surface/surfaces is it applied? • A) The nail and screw heads • B) The wood substrate and the back side of the plastic laminate • C) The plastic laminate only • D) The wood substrate only

  11. When do you know it is time to bond the plastic laminate and the wood substrate together? When the contact cement is dry When the contact cement is tacky When the contact cement turns pink As soon as you finish putting the contact cement on

  12. What keeps the two parts from bonding together until the laminate is in the proper position? A bead of yellow glue Bar clamps A damp cloth Spacers put between the plastic laminate and the wood substrate, such as wooden dowels or slats

  13. How do you make sure the laminate and wood substrate are completely bonded together? You put c clamps around the edges You roll over the plastic laminate from the center out with a J roller You vibrate sand it You heat it with a hot air gun

  14. After bonding the plastic laminate and the wood substrate together how do you trim the excess plastic laminate? • Cut it on the table saw • Sand it flush • Trim it with a flush trim bit in a router • Cut it with the panel saw

  15. What do you do to the trimmed edge of the laminate to make sure no one gets cut by it? File the edge of it on a 45 degree angle Sand it flat Micro groove it Paint it

  16. What do you do if you have to remove the laminate from the wood substrate? Hammer it off Raise a corner, and spray lacquer thinner between the wood substrate and plastic laminate Saw it with a band saw Pull it off with a crow bar

More Related