1 / 65

Electrical Safety

Electrical Safety. Introduction. Electricity is essential to modern life Some employees work with electricity directly Some indirectly Electricity is a serious workplace hazard Electricity can be productive and safe. Agenda. Vocabulary Misconceptions and myths about electricity

kaden-puckett
Télécharger la présentation

Electrical Safety

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Electrical Safety

  2. Introduction • Electricity is essential to modern life • Some employees work with electricity directly • Some indirectly • Electricity is a serious workplace hazard • Electricity can be productive and safe

  3. Agenda • Vocabulary • Misconceptions and myths about electricity • Electrical shock and other injuries • Electrical hazards • Electrical safety for maintenance and custodial employees • Electrical safety for offices and classrooms

  4. Voltage Low voltage High voltage Current Resistance Conductor Insulator Ohm’s law Vocabulary

  5. Voltage • Electromotive force • Electrical potential energy • “Pressure” • Measured in volts (V)

  6. Low Voltage • Electrical installations and electrical equipment operating or intended to operate on systems of 600 volts, nominal, or less. • All work performed directly on or in proximity to such electrical installations, equipment, or systems.

  7. High Voltage • Electrical installations and electrical equipment operating or intended to operate on systems of more than 600 volts. • All work performed directly on or in proximity to such electrical installations, equipment, or systems. • Beyond the scope of this training.

  8. Current • The continuous movement of electrons past a given point • Measured in amperes (amps) (A) • Sometimes the symbol “I” is used

  9. Resistance • Opposition to the movement of electrons • Resistance is used for direct current • Measured in ohms (Ω) • “Impedance” is the proper term for alternating current • “Resistance” is commonly used

  10. Conductor • A person who collects tickets on trains • A person who leads a orchestra, band, or choir

  11. Conductor • A substance or thing that allows electricity (or heat) to flow by passing energy from particle to particle • Silver, copper, gold, aluminum

  12. Insulator • A barrier that wraps conductive materials to protective against electric shock • A material with little or no conductive properties • High resistance • Glass, rubber, mica, and some plastics

  13. Ohm’s Law • R = V / A • One volt will cause a current of one ampere to flow through a conductor having the resistance of one ohm • V = A * R

  14. Ohm’s Law V (Volts) A (Amps) R (Ohms)

  15. Electrical Misconceptions • Electricity tends to go to ground • After it reaches ground, it disappears • Ground serves as just one of the electrical loops that misdirected current can use to get back to the grounded power source

  16. Misconception #2 • If an electrical appliance or tool falls into a sink or tub of water, the item will short and trip the circuit breaker • This may not happen because the sink or tub may be non-conductive and therefore not part of the loop to ground

  17. Misconception #3 • AC reverse polarity is not hazardous • Many tools have switches in only one of the two conductors serving the item • The switch is supposed to be on the “hot” conductor supplying he power

  18. Myths About Electricity • Electricity takes the path of least resistance • Current will take any conductive paths, high or low resistance, in order to return to the source that provides it power • Small amounts of current will flow through paths of high resistance

  19. Myth #2 • Double insulated power tools are doubly safe and will always provide safety • Double insulated power tools can be hazardous if dropped into water • Electrical current can flow out of the power tool into the water

  20. Myth #3 • It takes high voltage to kill;120 volts AC is not dangerous • Current is the culprit that kills • Voltage is a factor in determining how much current will flow

  21. Electrical Shock • A sudden and accidental stimulation of the body’s nervous system by an electrical current • Current will flow through the body when it becomes part of an electrical circuit

  22. Electrical Shock Dynamics

  23. Other Injuries • Burns • Falls • Injuries when machinery starts suddenly

  24. Electrical Burns • Current passing through tissue generates extreme heat • Skin damage at entry and exit • Internal tissue damage • Result from arcs or flashes • Thermal burns from overheated wires or equipment or fires

  25. Falls • Initiated by a shock • Muscles contract involuntarily • Worker can lose balance and fall

  26. Machinery Injuries • Unexpected activation • Shock • Pinch • Crush • Shear

  27. Electrical Hazards • Bare conductors • Insulation failure • Equipment failure • Static electricity • Heating and overheating • Electrical explosions

  28. Bare Conductors • Live overhead wires most common • Working on rooftops • Repair of electrical systems • Capacitors

  29. Insulation Failure • Heat and elevated temperatures • Moisture and humidity • Mechanical damage • Rodents, fungi • Chemical incompatibility

  30. Equipment Failure • Older portable tools • Energized housing • Broken connections • Wrongly replaced internal wiring • Lack of grounding plug

  31. Static Electricity • Occurs when two different materials contact and then separate • High voltage, low current • Flammable liquids • Lightning

  32. Heating and Overheating • Use of electricity results in heat • Can cause accidental fires • Burns out equipment • Equipment failure and ignition • Hot surfaces

  33. Electrical Explosions • Rapid overheating from overcurrents • Caused by short circuits, power surges, or lightning • Heated contaminants in oil-filledbreakers or transformers • Capacitors subject to wrong polarity

  34. Safety for Maintenance and Custodial Employees • Qualified electrical workers • Engineered protection • Safety considerations • Safe practices • Lockout/tagout • Personal protective equipment (PPE)

  35. Qualified Electrical Workers • A person, designated by the district,who by reason of experience orinstruction has demonstratedfamiliarity with the operationto be performed and thehazards involved

  36. Engineered Protection • Insulation • Grounding • Circuit breakers • Fuses • Ground-fault circuit interrupters

  37. Insulation • Parts of electrical equipment coated with a low-conductive material • Rubber mats to stand on • Rubber gloves • Insulated shoes

  38. Grounding • Protects from shock • Safeguards against fire • Protects against damage to electrical equipment

  39. System Grounding • One conductor of the circuit is intentionally connected to earth • Protects against high voltage contact • Stabilizes voltage in a system

  40. Equipment Grounding • Equipment grounded by a permanent and continuous connection or bond • Provides a path for dangerous fault current to return to system ground • Enables protective devices to operate

  41. Circuit Breakers • Guard against overloads of current • Ensure current flow does not produce heat that causes temperature to rise to dangerous levels • Break the current path • Thermal • Magnetic

  42. Fuses • Guard against overloads of current • Ensure current flow does not produce heat that causes temperature to rise to dangerous levels • Break the current path • Melt when current exceeds a designated value

  43. Ground-Fault Circuit Interrupters • Fast-acting electrical device sensitive to very low levels of current imbalance due to flow to ground • Reduces duration of a shock • Not an overcurrent device like a circuit breaker or fuse

  44. Types of GFCI • Circuit-breaker type • Receptacle type • Permanently mounted type • Portable type • Cord connected type

  45. Circuit-Breaker Type • A direct replacement for a standard circuit breaker • Installed in a panelboard • Includes the functions of a standard circuit breaker • Can protect an entire branch circuit with multiple outlets

  46. Receptacle Type • A direct replacement for a standard receptacle • Protects one or more receptacle outlets • Protects additional non-GFCI type receptacles connected “down stream” • Very popular because of low cost

  47. Permanently Mounted Type • Mounted in an enclosure • Designed to be permanently wired to the supply • Frequently used around large commercial swimming pools or similar wet areas

  48. Portable Type • Designed to plug into existing non-GFCI protected outlets • Contain one or more receptacle outlets protected by the GFCI module • Easily transported from one location to another • Approved for outdoor use • Some are listed as rainproof

  49. Cord Connected Type • Consists of an attachment plug which incorporates the GFCI module • Protects the cord and any equipment attached to the cord • Plug has non-standard appearance and is equipped with test and reset buttons

More Related