1 / 25

EE 230: Optical Fiber Communication Lecture 17

EE 230: Optical Fiber Communication Lecture 17. System Considerations. From the movie Warriors of the Net. Basic Network Topologies. Bitrate Distance Graph for various point to point link technologies. System Design. Determine wavelength, link distance, and bit-error rate

katina
Télécharger la présentation

EE 230: Optical Fiber Communication Lecture 17

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. EE 230: Optical Fiber Communication Lecture 17 System Considerations From the movie Warriors of the Net

  2. Basic Network Topologies

  3. Bitrate Distance Graph for various point to point link technologies

  4. System Design • Determine wavelength, link distance, and bit-error rate • Work out power budget • Work out risetime budget • Work out cost budget

  5. Power Budget Steps • Start with BER and bit rate, determine B based on coding method • B = 1/2RC gives the maximum load resistance R based on B and C • Based on R and M, determine detector sensitivity (NEP), multiply by B1/2 • Add system margin, typically 6 dB, to determine necessary power at receiver

  6. Power budget steps, continued • Add power penalties, if necessary, for extinction ratio, intensity noise (includes S/N degradation by amplifiers), timing jitter • Add loss of fiber based on link distance • Include loss contributions from connections and splices • End up with required power of transmitter, or maximum length of fiber for a given transmitter power

  7. Power budget example Imagine we want to set up a link operating at 1550 nm with a bit rate of 1 Gb/s using the RZ format and a BER of 10-9. We want to use a PIN photodiode, which at this wavelength should be InGaAs. The R0 for the diode is 0.9 A/W.

  8. Bandwidth required for bit rate • For NRZ format, B=0.5 times bit rate • For RZ format, B=bit rate For this example, the bandwidth B is equal to the bit rate, 109 /s.

  9. Bandwidth limit C=2 pF for this photodiode. B = 1/2RC, so the load resistance R must be (2BC)-1 = 79.6 

  10. Noise Equivalent Power (NEP) Signal power where S/N=1 Units are W/Hz1/2 In this case, M=1 and the dark current = 4 nA. The factor outside the radical is 1/R0. We can thus determine the NEP, which is 5.1x10-7 W, which equals -33.0 dBm.

  11. Q Factor and BER For our BER of 10-9, Q=6 and S/N=12

  12. Extinction ratio penalty Extinction ratio rex=P0/P1 If our extinction ratio is 0.1, the penalty is 0.87 dB.

  13. Intensity noise penalty rI=inverse of SNR of transmitted light Since our S/N is 12, rI=0.83, which leads to a power penalty of 1.25 dB

  14. Timing jitter penalty Parameter B=fraction of bit period over which apparent clock time varies If our jitter represents 10% of the bit period, the power penalty is 0.34 dB

  15. Fiber attenuation If the attenuation in the fiber is 0.2 dB/km and the link is 80 km long, the total loss in the fiber will be 16.0 dB

  16. Example results • Minimum power required for receiver: -33.0 dBm • Safety margin: 6.0 dB • Extinction ratio power penalty: 0.87 dB • S/N power penalty: 1.25 dB • Timing jitter power penalty: 0.34 dB • Fiber loss over 80 km: 16.0 dB • Total= minimum transmitter power= -8.54 dBm=0.14 mW=140 W

  17. Further steps Alternatively, previous data could be used with a fixed transmitter power to determine maximum length of a fiber link If power budget does not add up, one can • replace PIN photodiode with APD • add an EDFA to the link

  18. Power Budget Example

  19. Risetime Budget

  20. Rise time budget components • bit rate and coding format determine upper limit of rise time • rise time of transmitter (from manufacturer; laser faster than LED) • pulse spread due to dispersion • rise time of receiver (from manufacturer; PIN faster than APD) Rise time components are combined by taking the square root of sums of squares

  21. Upper limit for rise time • For NRZ format, Tr=0.70/B • For RZ format, Tr=0.35/B In this case, choose RZ format. Tr must thus be less than or equal to 0.35/109 = 350 ps

  22. Group Velocity Dispersion-based rise time Calculate from laser optical bandwidth if known, or from modulation rate: In this case, D=17 ps/nm-km, L=80 km, and =0.016 nm, so tf=21.8 ps.

  23. Modal dispersion rise time For multimode fiber, time spread due to modal dispersion is based on core index and fiber length L. For step-index fiber: For graded-index fiber:

  24. Total rise time For this example, tMD=0, tTR=100 ps, tRC=0.5 ns, and tGVD= 21.8 ps as before. tr is therefore 510 ps, and the rise time budget does not meet the limit. • Can use NRZ format • Use faster detector or transmitter • Use graded-index fiber for less dispersion

  25. Computer Based Link Simulation • Computer Simulation is often used to model opticla links to account for the complex interaction between components and nonlinear effects • Commercial simulation tools are now available such as: • Linksim from RSoft • and the tools from VPI Systems Fiber-Optic Communication Systems-G. Agrawal

More Related