1 / 16

Graphite Core Inspection, Measurement of Brick Stress

Graphite Core Inspection, Measurement of Brick Stress. M Brown – EDF-E E Kingston and X Ficquet - Veqter Ltd J Whittington – JFNL Ltd. Contents. Stresses within AGR graphite bricks Benefits of performing local stress measurement The Deep Hole Drilling method

landen
Télécharger la présentation

Graphite Core Inspection, Measurement of Brick Stress

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Graphite Core Inspection, Measurement of Brick Stress M Brown – EDF-E E Kingston and X Ficquet - Veqter Ltd J Whittington – JFNL Ltd INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  2. Contents Stresses within AGR graphite bricks Benefits of performing local stress measurement The Deep Hole Drilling method Application of the DHD method to graphite Phase 1 Laboratory based tool Summary of results Conclusions INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  3. Stresses within AGR graphite bricks • Internal stresses created by differential shrinkage across brick wall – as a result of irradiation gradient Tensile forces at Bore (early in life) Compressive forces at Bore (later in life) 3 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  4. Benefits of performing local stress measurements • A measurement method i.e. independent of models (if the core is extracted and DYM measured) • Could provide a new reduced uncertainty datum line (starting condition) • Validation route for FEA models • Measurement of stress state of brick – potential to assess brick to brick variability • Possible to infer stress value at keyways • Potential to improve predictions of the onset and rate of keyway root cracking 4 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  5. The Deep Hole Drilling Method (Veqter Ltd) Cross-section through simple component Stage 1 – Attach reference bushes Stage 2 – Gundrill reference hole Stage 3 – Measure reference hole 6 5 4 7 3 Weld 2 8 Bushes 1 Stage 4 – EDM coaxial core Stage 5 – Re-measure reference hole Ø0 Ø Air Probe diameter measurements 5 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  6. Application of the DHD method to graphite • Test drilling on Gilsocarbon and PG25 • Guhring solid carbide straight flute – best hole 6 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  7. Application of the DHD method to graphite • 4-point bend tests using Gilsocarbon and PG25 filter graphite • Comparison with stresses calculated from strain gauge values 7 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  8. Phase 1 Laboratory based tool (Veqter/JFNL) • Designed to fit in envelope of 243mm diameter • 3 functions, Pilot hole / Air Probe / Relief cutter • 90mm cutter depth, 10mm Ø pilot hole • Clamping mechanism to hold tool within brick • Internal calibration gauges within tool 8 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  9. Phase 1 Laboratory based tool (Veqter/JFNL) Ø243mm Maximum drilled depth of 90mm Weight ≈ 12kg 9 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  10. Phase 1 Laboratory based tool (Veqter/JFNL) • Two types of test bricks • Split and glued • Split and actuated via a scissor mechanism • Simple cylinders and real AGR bricks • Sensitivity tests – temperature, pressure, channel air flow • Bricks strain gauged – inside and outside 10 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  11. Summary of results – step 1 • Before and after trepanning – diameter measurements for each angle • Diameter measurements between 10.004 and 10.028mm Angle 2 Angle 3 (Simple cylinder brick) 11 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  12. Summary of results – step 2 • Calculate difference in measured diameter for each of the 8 angles • Differences in measured diameter between -6 to 18 microns 12 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  13. Summary of results – step 3 • Calculate stresses based on reference hole deformation and using P28 Young’s modulus • Comparisons with predicted stress based on strain gauge measurements 13 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  14. Summary of results – stress reversed • Tensile stress at bore – comparison with predicted stress calculated using strain gauge readings 14 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  15. Summary of results – as machined cylinder • Simple machined cylinder small tensile stress at bore – no external applied stress 15 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

  16. Conclusions • The Deep Hole Drilling method has been successfully developed with respect to measurements in virgin graphite. • Further work on the evaluation of the technique in representative porous material is required. • Sensitivity of the measurement to temperature, pressure and channel flow has been evaluated. • Measurements on a variety of pre-stressed bricks has demonstrated accuracy to better than 1MPa (comparison with strain gauge - scaled FEA models). • Resolution of the technique in Virgin AGR bricks has been shown to be better than 0.5MPa. 16 INGSM 14, Seattle 2013 - NOT PROTECTIVELY MARKED BEG/FORM/COMM/026A REV 007

More Related