1 / 59

CSA A23.3-04 Changes

CSA A23.3-04 Changes. NBCC load & combination factors  c changes from 0.6 to 0.65 Clause 8 – load and combination to appendix Clause 10 – small changes to slenderness Clause 11 – major changes Clause 13 – slab bands Clause 14 – major re-write Clause 15 – piles and pile caps added

lindsay
Télécharger la présentation

CSA A23.3-04 Changes

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CSA A23.3-04 Changes • NBCC load & combination factors • c changes from 0.6 to 0.65 • Clause 8 – load and combination to appendix • Clause 10 – small changes to slenderness • Clause 11 – major changes • Clause 13 – slab bands • Clause 14 – major re-write • Clause 15 – piles and pile caps added • Clause 21 – major changes • Clause 23 – minor changes • Append D – anchorage is all new

  2. Clause 10 Flexure and Axial Loads The old simplified equation for effective moment of inertia has been changed.

  3. Clause 11 Shear and Torsion • This Clause has major changes. • The simplified and general method approach is gone, there is now only one. • The cases previously covered by the simplified method are now special cases. • The general method has been changed and the tables are gone replaced by equations.

  4. Clause 11 Shear and Torsion

  5. Clause 11 Shear and Torsion 11.3.6.2 Values for Special Member Types Unless permitted otherwise by Clause 11.3.6.3 or Clause 11.3.6.4, the value of β shall be taken as 0.21 and θ shall be taken as 42° for any of the following member types (a) slabs or footings with an overall thickness not greater than 350 mm; (b)footings in which the distance from the point of zero shear to the face of the column, pedestal or wall is less than 3 times the effective shear depth of the footing; (c) beams with an overall thickness not greater than 250 mm; (d)concrete joist construction defined by Clause 10.4; and (e) beams cast integrally with slabs where the depth of the beam below the slab is not greater than one-half the width of web nor 350 mm.

  6. Clause 11 Shear and Torsion 11.3.6.3 Simplified Method In lieu of more accurate calculations in accordance with Clause 11.3.6.4, and provided that the specified yield strength of the longitudinal steel reinforcement does not exceed 400 MPa and the specified concrete strength does not exceed 60 MPa, θ shall be taken as 35° and β shall be determined as follows (a) If the section contains at least minimum transverse reinforcement as required by Equation (11‑1) then β shall be taken as 0.18;

  7. Clause 11 Shear and Torsion • If the section contains no transverse reinforcement and the specified nominal maximum size of coarse aggregate is not less than 20 mm then • Alternatively, the value of b for sections containing no transverse reinforcement may be determined for all aggregate sizes by replacing the parameter dv in Equation (11‑9) by the equivalent crack spacing parameter sze where however sze shall not be taken less than 0.85sz. The crack spacing parameter, sz, shall be taken as dv or as the maximum distance between layers of distributed longitudinal reinforcement, whichever is less. Each layer of such reinforcement shall have an area at least equal to 0.003bwsz, see Fig. 11‑2.

  8. Clause 11 Shear and Torsion 11.3.6.4 General Method The values of β and θ shall be determined from the following equations

  9. Clause 13 Two-way Slab Systems • Major change - added slab bands • Narrowed the ranges of distribution to negative and positive steel in the column strips

  10. Clause 13 Two-way Slab Systems • Now have four categories: • Slabs -0.70 to 0.90 and + 0.55 to 0.65 • Drop Panels -0.75 to 0.90 and + 0.55 to 0.65 • Slab Bands -0.80 to 0.90 and + 0.80 to 1.0 • Slabs on Bands -0.05 to 0.15 within bb and rest uniformly distributed across entire width (including bb) • positive moment at all spans where 0.50 to 0.60 • positive moment at all spans where to

  11. Clause 13 Two-way Slab Systems • Slab Shear • size effect for two way (punching) shear • no more principle axis calculations • One-Way shear on revised perimeter for corner columns, just d/2 away from column and if column is in from the slab edge maximum of d beyond • Edge loads - minimum top steel between columns • Finite element analysis • Revised relations to deal with mxy

  12. Clause 14 Walls • Complete re-write to address the wider range of walls being designed. • Three basic categories • Bearing walls • Non-bearing walls • Shear walls • Covers many general requirements such as: • lateral support • concentrated loads • vertical loads through floors and shear across construction joints

  13. Clause 14 Walls • Wall — vertical slab element, which may or may not be required to carry superimposed in-plane loads, in which the horizontal length, ℓw, is at least 6 times the thickness, t, and at least 1/3 of the clear height of the element. • Bearing Wall – a wall that supports • Factored in plane vertical loads exceeding 0.1 fc’Ag • weak axis moments about a horizontal axis in the plane of the wall • Shear forces necessary to equilibrate the forces in (b)

  14. Clause 14 Walls • Non-bearing Wall – a wall that supports factored in plane vertical loads less than or equal to 0.1 fc’Ag and, in some cases, moments about a horizontal axis in the plane of the wall and the shear forces necessary to equilibrate those moments. • Shear wall – a wall or an assembly of interconnected walls considered to be part of the lateral-load-resisting system for a building or structure. Shear walls support • Vertical loads • Moments about horizontal axes perpendicular to the wall (strong axes bending) • Shear forces acting parallel to the plane of the wall

  15. Clause 14 Walls 14.1.8.7 Ties for Distributed Vertical Compression Reinforcement. Distributed vertical reinforcement, if stressed in compression, shall be tied and detailed in accordance with the provisions for column reinforcement in Clause 7, except that ties can be omitted if: • the area of vertical steel is less than 0.005Ag, and • the bar size is 20M or smaller.

  16. Clause 15 Foundations • Extensively revised to add new treatment of piles and pile caps. • For example provides reductions for effective cross section and capacity for uncased piles. • Requires design for the range of specified tolerance with a minimum of ± 50 mm

  17. Clause 21 Seismic design • A general revision to align with NBCC changes such as the introduction of Rd and R0 as well as new drift limits. • Enumeration of code recognized ductile systems

  18. NBCC Concrete Ductile Systems

  19. Plastic Hinges to Absorb Energy

  20. Example Unclassified Systems

  21. Clause 21 Seismic design • Removal of limit of 55 MPa on f’c. • Revised (revised from CPCA Handbook values) effective stiffness factors for wall and coupling beams to be used for analysis. • New relations for transverse reinforcement for Rd = 4.0 columns including the effect of axial load level.

  22. Clause 21 Seismic design 21.2.1.2 For the purposes of determining forces in and deflections of the structure, reduced section properties shall be used. Table 21‑1 lists the effective property to be used as a fraction of the gross section property. Table 21‑1

  23. Clause 21 Seismic design • Column and wall stiffness reduction factors

  24. Column Confinement (Cl. 21.4.4.2)

  25. 20 Clause 21 Changes – Ductile Walls • Clarification of when a wall with openings may be treated as a solid wall • Revised requirements for the extent of ductile detailing over the building height • Added tying requirements for distributed reinforcement in ductile walls reflecting changes to Clause 14. • Clarified the minimum concentrated reinforcement requirements for flanged walls • Explicitly named “buckling prevention” ties

  26. Plastic Buckling + Tension Yield

  27. Clause 21 Seismic design • Revised relations for wall ductility that include consideration of the effects of height to width ratio and design displacement on ductility demand. • Relations framed in terms of wall rotational demand and wall rotational capacity. • Requirement to check rotational demand and rotational capacity of coupling beams.

  28. Clause 21 Changes – Ductile Walls • Introduced a “ductility” limit state for plastic hinges in walls and coupling beams • Rotational capacity ≥ Rotational demand • Added requirement to check rotational demand and rotational capacity of coupling beams

  29. Rotational Demand (Cl. 21.6.7.2)

  30. Rotational Capacity (Cl. 21.6.7.3)

  31. Coupled Walls 21.6.8.2 The inelastic rotational demand on Ductile Coupled and Partially Coupled Walls shall be taken as: where is the total Design Displacement.

  32. Coupled Walls

  33. Coupling Beams 21.6.8.4 The inelastic rotational demand on coupling beams shall be taken as: The inelastic rotational capacity of coupling beams ic shall be taken as: (a) 0.04 for coupling beams designed with diagonal reinforcement in accordance with Clause 21.6.8.7 and (b) 0.02 for coupling beams designed in accordance with Clause 21.6.8.6.

  34. Pin Ended Coupling Beam

  35. Pin Ended Example

  36. Pin Ended Case (Cl. 21.6.8.9)

  37. Pin Ended Case (Cl. 21.6.8.9) 21.6.8.9 If the wall at one end of the coupling beam has a factored resistance less than the nominal coupling beam resistance, the following requirements shall be satisfied: (a) the coupling beam shall satisfy the shear stress limitations of Clause 21.6.8.5 and the requirements of Clause 21.6.8.6 (b) the wall shall be designed to the requirements of Clauses 21.4.4.1 to 21.4.4.3, Clauses 21.4.4.6 and 21.4.5 (c) the joint between the wall and the coupling beam shall satisfy Clause 21.5.

  38. Torsion on Tubes

  39. Torsion on Tubes 21.6.8.12 Assemblies of Coupled and Partially Coupled Shear Walls connected together by coupling beams which function as a closed tube or tubes shall be designed with: (a) that portion of the overturning moment due to lateral loads resisted by axial forces in the walls, increased at each level by the ratio of the sum of the nominal capacities of coupling beams to the sum of the factored forces in the coupling beams required to resist lateral loads above the level under consideration (b)an additional increase in overturning moment resisted by axial forces in the walls at each level corresponding to the increase in the sum of the nominal capacities of the coupling beams above the level under consideration required to resist the accidental torsion.

  40. Forces @ Plastic Hinge Level

  41. Forces @ Plastic Hinge Level 21.6.8.13 In lieu of a more detailed assessment, wall segments that act as tension flanges in the flexural mode shall be assumed to have no shear resistance over the height of the plastic hinge. For assemblies of wall carrying torsion as a tube, the shear forces in the tension flange shall be redistributed.

  42. Clause 21 – Moderate Ductility • Changes to the requirements for nominally ductile frame systems reflecting the revised Rd value • Moderately ductile frame columns now have be stronger than the frame beams • Revised frame column tie requirements using the new confinement relations • Trigger added for tilt-up wall systems

  43. Tilt-up Walls 21.7.1.2 Tilt-Up Wall Panels shall be designed to the requirements of Clause 23 except that the requirements of Clause 21.7.2 shall apply to wall panels with openings when the maximum inelastic rotational demand on any part of the panel exceeds 0.02 radians and in no case shall the inelastic rotational demand exceed 0.04 radians. The requirements of Clause 21.7.4 shall apply to solid wall panels when the maximum in plane shear stress exceeds . Note: Methods for calculating rotational demand on elements of tilt-up panels with openings can be found in Explanatory Notes to CSA Standard A23.3-04 published by Cement Association of Canada. The seismic performance of tilt-up buildings depends not only on the performance of the concrete wall panels, but also the performance of the roof structure and the connection between the wall panels and the roof. Only the design of the concrete wall panels is within the scope of this standard.

  44. Clause 21 – Moderate Ductility • Rotational limit state design approach introduced for moderately ductile walls • Simplified method included for cases with moderate vertical loads or limited lateral deflections • Special requirements for squat walls introduced.

  45. Squat Walls (Cl. 21.7.4) • Squat Shear Walls, hw/ℓw ≤ 2.0 • Rd = 2.0 • Two possible hinge types • Flexural yield • Shear yield

  46. Clause 21 – Squat Walls

  47. Clause 21 Changes – Added Sections • Requirements for Rd = 1.5 buildings introduced. • Frames • Walls • 2-way slabs • New requirements for precast buildings. • Essentially ACI.

  48. Clause 21 Seismic design • New section on structural diaphragms. 21.10.3.1 Diaphragm shall be idealized as a system consisting of the following components arranged to provide a complete load path for the forces: (a) chords proportioned to resist diaphragm moments as tensions and compression forces. (b) collectors arranged to transfer the forces to, from and between the vertical Seismic Force Resisting Systems. (c) either shear panels to transfer forces to, from and between the chords and collectors or (d) continuous strut and tie in-plane shear trusses.

  49. Clause 21 Seismic design • New section on foundations. • Essentially detailing rules • Extensive revisions to requirements for structural elements not part of the Seismic Force Resisting System.

More Related