1 / 49

OSHA Region IV

OSHA Region IV. Electrical Outreach General Industry Photos 29 CFR 1910 Regulations. General Industry Photos. Standard 1910.254(d)(9)(iii) Description Welding lead cable splice were not insulated. All splices and metal parts of cables and parts must be guarded. .

lotus
Télécharger la présentation

OSHA Region IV

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. OSHA Region IV Electrical Outreach General Industry Photos 29 CFR 1910 Regulations

  2. General Industry Photos • Standard • 1910.254(d)(9)(iii) • Description • Welding lead cable splice were not insulated. All splices and metal parts of cables and parts must be guarded.

  3. General Industry Photos • Standard • 1910.303(b)(1) • Description • Building wiring systems were not properly installed. Wiring draped over building surfaces.

  4. General Industry Photos • Standard • 1910.303(b)(2) • Description • Equipment not installed IAW listing requirements.

  5. General Industry Photos • Standard • 1910.303(g)(1)(iii) • Description • Access to circuit breaker panels blocked.

  6. General Industry Photos • Standard • 1910.303(g)(2)(i) • Description • Live parts exposed.

  7. General Industry Photos • Standard • 1910.303(g)(2)(i) • Description • The receptacle was not properly installed in the junction box which exposed energized parts.

  8. General Industry Photos • Standard • 1910.303(g)(2)(i) • Description • Broken electrical receptacle exposing energized parts.

  9. General Industry Photos • Standard • 1910.303(g)(2)(i) • Description • Live parts of 480 VAC electrical system exposed. All live parts are required to be guarded.

  10. General Industry Photos • Standard • 1910.303(g)(2)(i) • Description • Front cover removed from circuit breaker panel. Live parts exposed.

  11. General Industry Photos • Standard • 1910.304(f)(5)(v) • Description • Portable light with metal guard which is required to be grounded.

  12. General Industry Photos • Standard • 1910.304(f)(5)(v) • Description • The ground pin was removed from the electric plug.

  13. General Industry Photos • Standard • 1910.305(a)(2)(iii)(G) • Description • Electrical wiring was not protected from damage. Lying across road where cranes and other vehicular traffic could pass over the wiring.

  14. General Industry Photos • Standard • 1910.305(b)(2) • Description • The faceplate was removed from the  receptacle exposing the energized parts.

  15. General Industry Photos • Standard • 1910.305(e)(1) • Description • Electrical systems were not designed for wet and damp locations

  16. General Industry Photos • Standard • 1910.305(g)(2)(iii) • Description • The electrical plug did not have adequate strain relief which causes stress on the contacts.

  17. General Industry Photos • Standard • 1910.305(j)(1)(iv) • Description • Electric cords and cables lying in water.

  18. General Industry Photos • Standard • 1910.305(j)(1)(iv) • Description • The receptacle which was approved for wet and damp locations was damaged.

  19. General Industry Photos • Standard • 1910.307(b)(1) • Description • Electrical wiring was not approved for hazardous locations. Paint spray area.

  20. General Industry Photos • Description • Electrical wiring and systems were not installed IAW NEC.

More Related