1 / 16

JUICE/RPWI/MFR

JUICE/RPWI/MFR. W. Kurth & D. Kirchner RPWI Team Meeting Uppsala, 9-11 May 2012. JUICE MF Receiver. 22.5MHz. 1MHz LPF. 14 Bit A/D. 1kHz HP. RTAX4000. Gain SW. 1MHz LPF. 14 Bit A/D. 1kHz HP. Gain SW. 512KX32 SRAM. 14 Bit A/D. 1MHz LPF. 1kHz HP. Gain SW. Serial I/F. FPGA.

martina-nichols
Télécharger la présentation

JUICE/RPWI/MFR

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. JUICE/RPWI/MFR W. Kurth & D. Kirchner RPWI Team Meeting Uppsala, 9-11 May 2012

  2. JUICE MF Receiver 22.5MHz 1MHz LPF 14 Bit A/D 1kHz HP RTAX4000 Gain SW 1MHz LPF 14 Bit A/D 1kHz HP Gain SW 512KX32 SRAM 14 Bit A/D 1MHz LPF 1kHz HP Gain SW Serial I/F

  3. FPGA Serial I/F A/D Controller WvFE Core Control State Machine Pseudo-PROM Memory Controller

  4. Operating Scenarios • Cassini HFR-like serial interface • Very low impact interface • Simplifies packaging • What requirements are there for data time-tagging? • RBSP Data bus interface • Tight integration required with host processor

  5. Self-contained processing • Use FPGA gates for PROM • Simplifies interface, lowers requirements on host flight software • Patches still available as in Cassini HFR

  6. Digital Daughter Board 22.5MHz Serial Rcvr 1.5 Pass Xstor RTAX4000 Serial Xmtr Voltage Ref 1.8 Pass Xstor 32x512K

  7. Power • Derive Memory and RTAX core voltages from 3.3V line • Less efficient but lower impact to interface • If available, ~2V core voltage supply could be used to lower the power dissipated in linear regulator • Run Analog from +/-6 • Switch the analog power to Receiver Board • Assuming a 3.3V logic interface

  8. RH1498 @ 2.5maX2 5 packages = 25ma@12v=300mW RH1013 @.6maX2 4 packages = 4.8ma@12V= 60ma RHF1401 3 packages@ 50mw average 150mW Xstal Osc 50mw RTAX standby 150mw Mem standby 20mW Serial I/O 50mW Power

  9. Power Profile ~1 sec ~2W ~4 sec ~1W ~0.5W baseline

  10. Top View 21.5cm Juno (could fit on 14.8x21cm) 16.5cm

  11. Side View 3cm Mass Estimate 600g without housing

  12. MFR Processing • Data capture • FFT • Bin & average (quasi-log spectrum) • Waveform compression (for waveform mode)

  13. MFR Calibrations • Primary calibrations occur prior to launch • Establish Vin – Vout relationship • Determine frequency response • Desire data in cruise (if possible) and during Earth flyby to evaluate performance, compare to other instruments • In-flight calibrations will involve establishing electron density (and temperature) consistency with measurements by other means (LP, particle instruments, etc.)

  14. Antenna Interface To RPWI To RPWI SSR Matching RPWI Hi-Z Preamp RPWI Hi-Z Preamp To SSR Switching between SSR and RPWI done with fault tolerant switch matrix controlled by spacecraft

  15. Juno Electric Preamp • 50Hz-45MHz front end with output split into three bands with individual attenuators • High amplitude capability (5V/M Decametric, 70V/m VxB at spin rate) • High radiation tolerance • Qualified to 400krads (could have gone higher) • Components tested to 1Mrad

  16. Juno preamp cont’d • Power 1.5W +.5W heater power • Power utilization impacted by high amplitude capability and multiple output drivers

More Related