1 / 12

Black Box Electronics

Black Box Electronics. An Introduction to Applied Electronics for Physicists 2. Analog Electronics: BJTs to opamps University of Toronto Quantum Optics Group Alan Stummer, Research Lab Technologist. Active BJTs. Class A with four resistors. Class A with negative feedback.

mikkel
Télécharger la présentation

Black Box Electronics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Black Box Electronics An Introduction to Applied Electronics for Physicists 2. Analog Electronics: BJTs to opamps University of Toronto Quantum Optics Group Alan Stummer, Research Lab Technologist

  2. Active BJTs Class A with four resistors Class A with negative feedback

  3. MOSFETs(Metal Oxide Semiconductor Field Effect Transistor) • Drain to source resistance and/or current ≈ 1 / gate to source voltage. • Zero gate current! • Operate in active region (analog), or saturation or cutoff (digital). • Most are N-channel (source grounded, positive drain and gate). • Limited in current ID, voltage VDS and power PD. • Very good saturation, RDS(on). • Limited frequency range, capacitance dominates at high frequency. • Select for current, voltage, speed and RDS(on) if saturating. • Typical voltage VDS range 10V to 200V, extreme to 1.5KV. • Typical current ID range 100mA to 10A, extreme 10mA to 100A.

  4. Sample FET Transfer Curves A general purpose 48A, 60V N-FET from Fairchild (Digikey.ca). http://www.fairchildsemi.com/ds/ND/NDP6060L.pdf

  5. NDP6060L Data Sheet – Parametric Section

  6. Basic Q Switching

  7. Sample Linear FET Circuit Opamp uses a N-FET to increase current driving capacity. The opamp can supply only ten’s of mA but the laser needs ten times more. • The opamp can drive the FET from cutoff through to saturation. • All of the laser current goes through R9. • The opamp monitors the R9 voltage. • The opamp adjusts the FET gate voltage to control the FET conductance.

  8. Less Common Active Parts • IGBT (Insulated Gate Bipolar Transistor) • Current allowed through collector to emitter is proportional to voltage between gate and emitter. • Voltage controlled like a FET, switches like a BJT. • Used for power control such as motors. • Pros: High voltage and current. Cons: slow, poor saturation. • Thyristers: SCR (Silicon Controlled Rectifier)& Triac • Anode/MT1 connects to cathode/MT2 once gate current exceeds threshold, stays on until anode/MT1 current drops below threshold. • SCR is unipolar, Triac is bipolar. • Used for motor and lighting controls (Φ control). • Pros: High voltage and current. Cons: slow, poor saturation.

  9. OPAMPs(Operational Amplifiers) • Five terminal linear device (2 power, 2 inputs, one output). • Hard Rule #1: The output goes positive if the input is positive (where input is defined as +ve input relative to –ve input). • Soft Rule #2: The inputs and output can only range between the “rails” (the positive and negative supply pins). • All else is imperfections:

  10. Some OpAmp Errors

  11. Basic OpAmp Amplifiers

  12. Ω The End Ω Next: 3. Digital Electronics 4. Sample Circuits 5. Spice simulations Then: More in depth on anything? Suggestions?

More Related