180 likes | 201 Vues
Statistical Data Analysis. Prof. Terry A. Ring, Ph. D. Dept. Chemical & Fuels Engineering University of Utah. http://www.che.utah.edu/~geoff/writing/index.html. Making Measurements. Choice of Measurement Equipment Accuracy – systematic error associated with measurement.
E N D
Statistical Data Analysis • Prof. Terry A. Ring, Ph. D. • Dept. Chemical & Fuels Engineering • University of Utah http://www.che.utah.edu/~geoff/writing/index.html
Making Measurements • Choice of Measurement Equipment • Accuracy – systematic error associated with measurement. • Precision – random error associated with measurement.
Definitions • Error – the difference between the measured quantity and the ”true value.” • The “true value” is not known!!! • So how do you calculate the error?? • Random errors - the disagreement between the measurements when the experiment is repeated • Is repeating the measurement on the same sample a new experiment? • Systematic errors - constant errors which are the same for all measurements. • Bogus Data – mistake reading the instrument
Random Error Sources • Judgement errors, estimate errors, parallax • Fluctuating Conditions • Digitization • Disturbances such as mechanical vibrations or static electricty caused by solar activity • Systematic Error Sources • Calibration of instrument • Environmental conditions different from calibration • Technique – not at equilibrium or at steady state.
Statistics • Mean xM • Deviation xi-xM • Standard Deviation • Confidence level or uncertainty, • 95% confidence = 1.96 • 99% confidence = 2.58 • Please note that Gaussian distributions do not rigorously apply to particles- log-normal is better. • Mean and standard deviation have different definitions for non-Gaussian Distributions
Comparison of means – Student’s t-test • v= n1+n2-2 • use the t-value to calculate the probability, P, that the two means are the same.
Estimating Uncertainties or Estimating Errors in Calculated Quantities –with Partial Derivatives • G=f(y1,y2,y3,…) http://www.itl.nist.gov/div898/handbook/mpc/section5/mpc55.htm
Way around the Partial Derivatives This approach applies no matter how large the uncertainties (Lyons, 1991). (i) Set all xi equal to their measured values and calculate f. Call this fo. (ii) Find the n values of f defined by fi = f(x1,x2,...,xi+si,...,xn) (11) (iii) Obtain sf from (12) If the uncertainties are small this should give the same result as (10). If the uncertainties are large, this numerical approach will provide a more realistic estimate of the uncertainty in f. The numerical approach may also be used to estimate the upper and lower values for the uncertainty in f because the fi in (11) can also be calculated with xi+ replaced by xi-.
Equation Used f/f0 (9) 0.011968 (12) with + 0.011827 (12) with - 0.012113 Now try the same calculation using the spread sheet method. The dimensionless form of (12) is (after taking the square root) (17) The propagated fractional uncertainties using (15) and (17) are compared in Table 4. A further advantage of the numerical approach is that it can be used with simulations. In other words, the function f in (12) could be a complex mathematical model of a distillation column and f might be the mole fraction or flow rate of the light component in the distillate. Table 4. Uncertainties in Gas Velocity Calculated from (15) and (17) See web page with sample calculation done with Excel
Fitting Data • Linear Equation – linear regression • Non-linear Equation • Linearize the equation- linear regression • Non-linear least squares
Rejection of Data Points • Maximum Acceptable Deviations (Chauvenet’s Criterion)
Example • xi-xM/=8.9-8.2/0.3=2.33 • xi-xM/=7.9-8.2/0.3=1.0
Regression • Linear Regression • good for linear equations only • Linearize non-linear equation first • linearization leads to errors • Non-linear Regression • most accurate for non-linear equations • See Mathcad example
Residence Time Measurements T T Time(min) Time(min) T=(To-Tin)exp(-t/tau)+Tin
Non-Linear Fit Linearized Eq. Fit Flow Calc.s Temperature(C) Time (min)