1 / 38

Instructor Training MPTT Flow Loop System

Instructor Training MPTT Flow Loop System. VLP-TRN-MPTT. Terminal Objective. Given procedure TROP-MPTT-10058-01, Multi-Purpose Team Trainer, operate the Flow Loop System per procedure without violating any safety requirements. [1.0]. Enabling Objectives.

orlando-hester
Télécharger la présentation

Instructor Training MPTT Flow Loop System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Instructor Training MPTT Flow Loop System VLP-TRN-MPTT

  2. Terminal Objective • Given procedure TROP-MPTT-10058-01, Multi-Purpose Team Trainer, operate the Flow Loop System per procedure without violating any safety requirements. [1.0]

  3. Enabling Objectives • Using the Flow Loop System and its operating procedure TROP-MPTT-10058-01, Multi-Purpose Team Trainer, identify system components for proper system alignment to support operation.[1.1]

  4. Enabling Objectives • Using EN-IS-123 Electrical Safety, identify potential electrical safety concerns during a walk down of the Flow Loop System.[1.2]

  5. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, and the Flow Loop System P&ID, determine the available flow paths that can be established for Loop Operation.[1.3]

  6. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, section 8.4, explain how to set the Moore 353 to configuration required for start up of the Flow Loop system. [1.4]

  7. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, section 8.5, explain the proper method used to put a pump into service while monitoring system response for proper indications.[1.5]

  8. Multi Purpose Team TrainerFlow Loop System

  9. MCC & LP

  10. Circuit 1 Circuit 2 Circuit 3 Circuit 4 Circuit 6 Circuit 5 DC Breaker Panel

  11. DC Breaker AC Breaker Battery Charger

  12. EN-IS-123 • 5.2.7 Personnel operating circuit breakers or disconnect devices opened or closed, on an energized bus, shall stand clear to one side, preferably on the hinged side, when practical.

  13. EN-IS-123 • PPE Requirements See attachment 9.3 for different voltage levels.

  14. EN-MA-131 • This procedure provides the process and necessary administrative lock out/tag out controls of hazardous energy sources for non-plant related (NPR) equipment not under the control of Operations and EN-OP-102 (Protective and Caution Tagging). Entergy

  15. EN-MA-131 • If protection is required under this procedure there is a log book in the Flow Loop Control room and a Lock Out set stored in the Pre job brief room. • F-ADM-NON-PLANT LOCKOUT TAGOUT is the Qual for using this procedure.

  16. Flow Loop Big Picture

  17. Supply Tank

  18. P-200-1A, B

  19. Instrument Air P&ID

  20. Air Compressor Power Disconnect Switch

  21. System Filter

  22. LCV & Transmitters

  23. AOV’s & MOV’s

  24. Rosemont Analog Trip

  25. Main Control Panel

  26. Main Control Panel

  27. Siemens / Moore 353 Controller • Top display shows value selected by “D” key • S = Setpoint = Remote or Local • P = Process = Analog Input • V = Valve = Analog Output Special Function If programmed, Resets functions as labeled Will display units (GPM) on lower display Set point adjust Auto / Manual Select Functions not normally used except for Auto tune

  28. Pump Amps/Pressure

  29. Pump Status

  30. Review Objectives

  31. Enabling Objectives • Using the Flow Loop System and its operating procedure TROP-MPTT-10058-01, Multi-Purpose Team Trainer, identify system components for proper system alignment to support operation.[1.1]

  32. Enabling Objectives • Using EN-IS-123 Electrical Safety, identify potential electrical safety concerns during a walk down of the Flow Loop System.[1.2]

  33. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, and the Flow Loop System P&ID, determine the available flow paths that can be established for Loop Operation.[1.3]

  34. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, section 8.4, explain how to set the Moore 353 to configuration required for start up of the Flow Loop system. [1.4]

  35. Enabling Objectives • Given TROP-MPTT-10058-01, Multi-Purpose Team Trainer, section 8.5, explain the proper method used to put a pump into service while monitoring system response for proper indications.[1.5]

More Related