1 / 18

Control of Thermoacoustic Instabilities: Actuator-Sensor Placement

Control of Thermoacoustic Instabilities: Actuator-Sensor Placement. Pushkarini Agharkar, Priya Subramanian, Prof. R. I. Sujith Department of Aerospace Engineering Prof. Niket Kaisare Department of Chemical Engineering Indian Institute of Technology, Madras Acknowledgements:

rane
Télécharger la présentation

Control of Thermoacoustic Instabilities: Actuator-Sensor Placement

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Control of Thermoacoustic Instabilities:Actuator-Sensor Placement Pushkarini Agharkar, Priya Subramanian, Prof. R. I. Sujith Department of Aerospace Engineering Prof. Niket Kaisare Department of Chemical Engineering Indian Institute of Technology, Madras Acknowledgements: Boeing Travel Grant, IIT Madras Alumni Affairs Association, IIT Madras

  2. Thermoacoustic Instabilities Acoustics Heat Release Occur due to positive feedback mechanism between combustion and acoustic subsystems Representative system: ducted premixed flame Schuller (2003)

  3. Model of the ducted premixed flame • Control Framework • LQ Regulator • Kalman filter • Actuator Placement • LMI based techniques • based on Hankel singular values Conclusions

  4. Model of the ducted premixed flame acoustic subsystem • single actuator and sensor pair • actuator adds energy to the system • sensor measures acoustic pressure combustion subsystem

  5. Governing equation (linear) Combustion Subsystem

  6. Acoustic Subsystem fluctuating heat release contribution from controller Governing equations:

  7. Properties of the Model • Non-normality: due to coupling between combustion and acoustic subsystems • Nonlinearity: due to the equations of evolution of the flame front • Motivation: Reducing the transient growth and avoiding triggering

  8. State-Space Representation

  9. Linear Quadratic (LQ) Regulator such that the cost functional is minimized.

  10. Linear Quadratic (LQ) Regulator Open loop plant : (without control) Closed loop plant : (with control)

  11. LMI optimization problem - Linear Matrix Inequalities (LMI): inequalities defined for matrix variables

  12. Actuator Placement using LMI based Optimization Techniques

  13. Controllability–Observability Measures • Other ways to determine optimal placement of actuators and sensors • Controllability-Observability measure based on Hankel singular values (HSVs). • measure = • Hankel singular value

  14. Controllability–Observability Measures • Measure of controllability-observability based on HSVs calculated for various actuator and sensor locations • Locations of the antinodes of the third acoustic pressure mode give highest measure • From numerical simulations, the third acoustic mode is also the highest energy state

  15. Locations closer to the flame The techniques give contradictory results Antinodes of the least stable modes LMI based techniques Measures based on HSVs.

  16. Actuator Placement Numerical Validation In the presence of transient growth, actuators placed according to LMI techniques give better performance than when placed based on HSV measures

  17. Actuator Placement Numerical Validation 0.5 0.833 0.3 In the absence of transient growth, actuators placed according to HSV measures give better performance than in the presence of transient growth, but still not better than LMI techniques.

  18. Conclusions • Actuator-Sensor placement of non-normal systems requires different approaches than the ones used conventionally. • For the ducted premixed flame model, actuators placed nearer to the flame give better overall performance. • Controllers based on these actuators results in low transient growth as well as less settling time.

More Related