Repair concrete by using Low viscous Epoxy injection resin

1. Repair concrete by using Low viscous Epoxy injection resin Low viscous Epoxy injection resin is a solvent-free, 2-component super low viscosity-liquid, based on high strength epoxy resins. Specially for injecting into cavities and cracks in concrete. It is mainly used to fill and seal cavities and crack in structural concrete such as columns, beams, foundations, decks and water-retaining structures. Low viscous Epoxy injection resin is a 100% solid low viscosity epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity. 4 Epoxy is an ultra-low viscosity 4 low viscosity resins are excellent for the repair of cracks by gravity feeding. This 100% solids resin is insensitive to the presence of water, allowing application on damp or wet concrete surfaces. Two-component epoxy resin system planned specifically for gravity feeding or low-pressure infusion Applied with standard injection equipment, it will effectively grout and seal cracks in horizontal, vertical and overhead surfaces. This product can be used for crack repair in walls; it is thin enough to penetrate up to 2 in of sand on slab repairs from gravity alone. This epoxy should only be applied if the concrete is 40 Deg F or 10 Deg C or higher and allows for approx 4 days to cure. Very effective with low-pressure injection as slower setup time allows for extended injection time for complete penetration into cracks. 1001 Low viscous is a 100% solids, two- component, moisture insensitive epoxy designed to penetrate hairline cracks in concrete structures. Application of epoxy resin The infusion pressure during the infusion relies upon the nature and state of the construction. Start the infusion by filling the most reduced break zones with epoxy resin first. If there should arise an occurrence of flat splits, complete the infusion from one side so as to stay away from air considerations. While infusing the last packer check the air vent for rising gum. An auxiliary infusion ought to be completed inside the gelling period of the material (up to approx. 30 min after finish of serviceable life). Please note when applying epoxy resins: the response speed is impacted by the temperature of the material and the basic component. Higher temperatures quicken the response speed and drop temperatures back it off.

2. Sikadur 52 is a 2-part, 100% solids, and dampness lenient, epoxy glue. It is a low-thickness, high-quality glue planned explicitly for grouting both dry and soggy breaks. Utilize flawless for gravity feed or weight infusion of splits in auxiliary solid, brick work, wood, and so forth. Seal inside sections and outside above evaluation chunks from water, chlorides and gentle concoction assault and to improve wear ability. Surface Preparation Surface must be perfect and sound. It might be dry or clammy, yet liberated from standing water. Expel dust, laitance, oil, relieving mixes, impregnations, waxes and some other contaminants. Preparation Work: Concrete – Should be cleaned and arranged to accomplish a laitance and contaminant free, open finished surface by impact cleaning or equal mechanical methods. Steel – Should be cleaned and arranged altogether by impact cleaning or other comparable mechanical methods. Blending Proportion 1 section Component 'B' to 2 sections Component 'A' by volume into a perfect bucket. Blend completely for 3 minutes with Sika Paddle on low-speed (400-600 rpm) drill until consistently mixed. Blend just that amount that can be utilized inside its pot life. Application To gravity feed splits – Blow vee-scored break clean with oil packed air. Empty slick Sikadur 52 into vee-indented break. Proceed it until splits are totally filled. Preceding filling, seal underside of section if breaks reflect through. To pressure infuse breaks – Use robotized infusion hardware or manual technique. Set suitable infusion ports dependent on system utilized. Seal ports and breaks with Sikadur 31, Hi-Mod Gel, or Sikadur 33. At the point when the epoxy cement seal has restored, infuse Sikadur 52 with consistent weight. Satiate leads the way for specialist services and solutions for the construction industry. Satiate is the country’s leading provider of innovative solutions in Passive fire protection, Construction chemical and Low Viscous Epoxy Injection Resin. Advantages  Tenacious crack sealing grout.  Super low viscosity.  Suitable in both, dry and damp conditions.  High mechanical and adhesive strength.  Hard, but not brittle.  No shrinkage Visit us: http://www.satiates.in/low-viscous-epoxy-injection-resin.php Call us Today: +91 9960602620 / +91 9922000518