1 / 139

::Manual of Construction::

::Manual of Construction::. MENU OF THE MANUAL. ::CHAPTER CONTENT::. ::CHAPTER CONTENT::. 01 Bases of the system. 12 Tee branch: static derivation. 02 Tools. 13 Plenum. 03 Cutting the panels. 14 Offset. 04 Type of strips. 15 Square elbow with turning vanes.

seda
Télécharger la présentation

::Manual of Construction::

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ::Manual of Construction::

  2. MENU OF THE MANUAL ::CHAPTER CONTENT:: ::CHAPTER CONTENT:: 01 Bases of the system 12 Tee branch: static derivation 02 Tools 13 Plenum 03 Cutting the panels 14 Offset 04 Type of strips 15 Square elbow with turning vanes 05 Cross joints fit 16 Reinforcements 06 Longitudinal joints 17 Access door 07 Straight duct 18 Hangers and supports 08 Elbow 19 Outdoor duct 09 Reduction or transition 20 Unit conections 10 End cap 21 Installation of dampers & V.C.D. 11 Wye: dynamic derivation 22 Grilles, diffusers and flexible duct

  3. THE BASES OF THE SYSTEM 4.000mm 1º • Size of the panels: 3.000x1.200x20mm or 4.000x1.200x20mm

  4. THE BASES OF THE SYSTEM 4.000mm 2º • Cut of the longitudinal strips at 45º

  5. 4.000mm THE BASES OF THE SYSTEM 3º • Ducts assembled with four separate faces.

  6. Aluminium tape THE BASES OF THE SYSTEM Glue Silicone • Lengthwise glued, • Aluminium tape in trhe external longitudinals angles, • Silicone in the longitudinal internal angles.

  7. mm. 150 200 250 300 400 500 600 800 1000 1200 International Standards Standard Competitive • Cost control • Ex stock • Available with distributor Readiness • With the norms • With the environment Respectful Easy to build Construction • Assembling • Own workers • DID ADVANTAGES OF THE SYSTEM Practical Economical

  8. Code: TM0090VV Application No. 1: Single Cut 45º “V” SHAPE CUTTER Module only 1th. cut 45º Right 45º Left 45º Right Remove the Module

  9. Code: TM0090VV Application No. 2: Double Cut 90º “V” SHAPE CUTTER 4 3 5 2 1 Double Cut Double Cut Double Cut Double Cut Single Cut

  10. ::45º RIGHT JACK PLANE:: Code: TM0045RT 45º RIGHT JACK PLANE 45º Right

  11. Code: TM0090ST ::90º STRAIGHT JACK PLANE:: 90º STRAUGHT JACK PLANE 45º Straight

  12. Code: TM0045LT 45º LEFT JACK PLANE 45º Left

  13. CUT OF THE PANELS 4.000mm

  14. CUT OF THE PANELS 4.000mm

  15. ::CUT OF THE PANELS:: CUT OF THE PANELS Module 1th. cut Module 1th. cut

  16. 45ºLeft 45ºRight ::STRIP NORMAL :: STRIP NORMAL 1 • To build ducts with section =<1.200mm

  17. 45ºRight 45º Right STRIP SPECIAL 2 • To build ducts with section >1.200mm

  18. 300 mm Plenums 45º Right 90º Straight SPECIAL STRIP 3 • To build elbows, wye and special shares. Fixed meassure: 300mm

  19. Glue CROSS JOINTS: MALE & FEMALE FIT Air Flow Glue Figure 1

  20. Aluminium tape CROSS JOINTS: MALE & FEMALE FIT Air Flow Aluminium tape Figure 2

  21. Female CROSS JOINTS: MALE & FEMALE FIT Internal faces of the four strips

  22. Male CROSS JOINTS: MALE & FEMALE FIT Four sides of the external duct

  23. LONGUITUDINAL JOINTS Glue Aluminium tape Figure 1

  24. LONGUITUDINAL JOINTS Silicone Aluminium tape Figure 2

  25. STRAIGHT DUCT 4.000mm 1 • Select the four sides and to make the female before gluing.

  26. STRAIGHT DUCT Glue Glue 2 • Glue all the sides cut at 45º

  27. Aluminium tape STRAIGHT DUCT External face Level 3 • Unite the four sides with aluminum tape for the exterior.

  28. STRAIGHT DUCT Interior face 4 • Rotate the duct in position with the interior face up.

  29. PRÁCTICA: Construcción STRAIGHT DUCT 1 5 • Close the first side in position 90º vertical.

  30. STRAIGHT DUCT 2 6 • Also close the second side in position 90º vertical.

  31. STRAIGHT DUCT 3 7 • Close the third side.

  32. STRAIGHT DUCT Pressing 8 • Pressing the closing joint with the help of a piece of PVC pipe.

  33. Aluminium tape Silicone inside STRAIGHT DUCT 9 • Place the aluminum tape in the closing angle and the silicone.

  34. Aluminium tape Aluminium tape W+200mm ELBOW W+350mm W+350mm Cover bottom Cover top 1 • Draw the template of the cover bottom and cut toward “EXTERNAL”.

  35. Cover top ELBOW Cover bottom 2 • Copy the template and to cut on the contrary: toward the “INTERIOR”.

  36. 50mm 50mm BENT OF THE PANELS Interior face 20mm 50mm 50mm Exterior face 20mm

  37. BENT OF THE PANELS • Possibility to bend with different forms.

  38. ELBOW 3 • Cut the walls and make the female before of to glue.

  39. ELBOW Glue 4 • Glue all the sides cut at 45º

  40. ELBOW 5 • Paste the covers on the external wall.

  41. ELBOW 6 • Rotate the piece slowly on the external wall...

  42. ELBOW 7 • ...until the end.

  43. ELBOW 8 • Paste the internal wall beginning with the same place.

  44. Pressing Aluminium tape Silicone inside ELBOW 9 • To press, to tape, to clip and to make the male.

  45. 1:4 REDUCTION 4.000mm 1 • Select the four sides, draw and to cut the reduction.

  46. REDUCTION 2 • To make the female before gluing.

  47. REDUCTION Glue 3 • Glue all the sides cut at 45º

  48. Aluminium tape REDUCTION External face Level 4 • Unite the four sides with aluminum tape for the exterior.

  49. REDUCTION Interior face 5 • Rotate the duct in position with the interior face up.

  50. REDUCTION 1 6 • Close the first side in position 90º vertical.

More Related