1 / 24

Personal Trip-Odometer

Personal Trip-Odometer. By Akin Adekoya & David Chung. Table of Contents. Introduction Block Diagram Part Explanation Performance Problems Improvements Conclusion. Introduction. Reasons for our project Athletic improvements Future business opportunity A portable device . Objectives

starbuck
Télécharger la présentation

Personal Trip-Odometer

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Personal Trip-Odometer By Akin Adekoya & David Chung

  2. Table of Contents • Introduction • Block Diagram • Part Explanation • Performance • Problems • Improvements • Conclusion

  3. Introduction Reasons for our project • Athletic improvements • Future business opportunity • A portable device

  4. Objectives • Accurate conversion of accel. to distance • Reliable transmission and receiving • Keeping track of both the time and distance traveled by the user • Displaying the time and distance • Overall small and light

  5. Block Diagram Accelerometer Display User input Acceleration Data PIC PIC Transmitter Receiver Calculated Values Calculated Values Main Device Receiver/Display

  6. Polarity and over voltage protection + μ P – (+) (–) Zener diode + μ P – (+) 1N5822 or 1N5817 Schottky diode (–) Polarity Protection Fuse (eg. 1A) 1N5339 (eg. 5.6V) Parts shop: 1N4734 Over-voltage Protection

  7. Vdd 8 ST 7 XFILT 1 Cx1 T2 2 6 YFILT ADXL202 0.1u 5 COM 3 XOUT 4 Rset1 125k YOUT Accelerometer(ADXL202) • Single axis • 312mV/g • +-2g sensing • 125kOhm = 1000sample/s • 0.1uF = 50Hz BW 1.8mg rms Noise Analog output

  8. PIC I (16F877) • Voltage Divider • 20MHz Oscillator • Sample at 60Hz • Convert accel. to dist. • Output calculated dist. to transmitter

  9. Main equations • Vf = Vi + a*t • X = Vi*t + 0.5*a*t^2 where t = 1/60s a = acceleration from accelerometer Vi = Initial velocity Vf = Final velocity X = distance traveled

  10. Transmitter/Receiver (HP2) • Operating frequency = 903.37MHz • Operating temp. = 0~70 oC

  11. PIC II (16F877) • Input at 60Hz • 20MHz Oscillator • Reset Switch • Display Switch • Adds distance • Output to LCD

  12. LCD (Shelly)

  13. Final Device

  14. Performance • Accelerometer provided accurate values • First PIC converted analog acceleration accurately to digital distance • Transmitter/Receiver operated successfully • Second PIC was able to toggle between displaying time and distance

  15. Accelerometer at 0g

  16. Accelerometer at 1g (gravity)

  17. Accelerometer at 2g

  18. Calculation • (2.977V - 2.352V)/2 = 0.3125V/g • Value from data sheet = 0.312V/g

  19. Input and output of transmitter/receiver

  20. Challenges • Learning the PIC functions • Making the PIC work in synchronous with the entire circuit • Calibrating the Accelerometer • Accuracy decreases using a PIC (overflow) • Final product was functional but inaccurate

  21. Example (accelerometer reference differs each time) • Our zero g Bias was between 2.35~2.48 about 80% of the time.

  22. Improvements • Initial calibration as user turns on device • Use an op amp to improve the sensitivity • Make measurements in smaller standards to improve accuracy • Use microcontroller with more capability • Make the overall circuit smaller in size

  23. Conclusion • We have learned to work as a team to work on a real engineering project • We learned to use sensors, process the output data with a PIC, transmitting and receiving the data, and reprocessing to display our data

  24. Questions??

More Related