1 / 81

G.SHDSL MODEM / Router WireSpan 5350

G.SHDSL MODEM / Router WireSpan 5350. OVERVIEW. About G.SHDSL G . SHDSL was standardized in February 2001 internationally by ITU- T with recommendation G.991.2. G.SHDSL features symmetrical data rates from 192 Kbp s to 2304 Kbp s in 64 Kbp s increments for single pair copper.

tender
Télécharger la présentation

G.SHDSL MODEM / Router WireSpan 5350

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. G.SHDSL MODEM/ RouterWireSpan 5350

  2. OVERVIEW About G.SHDSL • G.SHDSL was standardized in February 2001 internationally by ITU-T with recommendation G.991.2. • G.SHDSL features symmetrical data rates from 192Kbps to 2304Kbps in 64Kbps increments for single pair copper. • G.SHDSL features symmetrical data rates from 384Kbps to 4608Kbps in 128Kbps increments for two pair copper. • G.shdsl incorporates rate adaptability from SDSL and the TC PAM modulation technique from HDSL-2, hence the “sh” in the name.

  3. OVERVIEW DSL Technology

  4. WireSpan 5350 Specification • 4 port 10/100M Base T, 1 G.SHDSL port and 1 port V.35 DB25 connector • Support ITU G.991.2 (G.SHDSL), G.SHDSL.bis • Supports Symmetric Data Rate of up to 2.3 Mbps (G.SHDSL), 5.6 Mbps (G.SHDSL.bis). • Support Bridged/Routed Ethernet over ATM • Support FRF.8 “Frame Relay/ATM Service Inter-Working” • Web-based configuration and monitoring. • Routing function. • NAT, DHCP function • Interoperable with all major DSLAM equipment.

  5. Hardware Connection

  6. Network Termination Point Network InterWorking Function (NIW): FRF.5Service InterWorking Function (SIW): FRF.8.1

  7. NIW and SIW functionalities NIW and SIW functionalities are two interworking modes between an ATM network and a Frame-Relay network:ATM Adaptation Layer 5 (AAL5).

  8. DSLAM Multiservice Frame-Relay DTE Serial SHDSL STM1 ATMNetwork ATM / Frame-Relay Interworking Function Frame-RelayNetwork Frame-Relay DTE Network InterWorking Function

  9. DSLAM Multiservice Frame-Relay DTE Serial SHDSL STM1 ATMNetwork ATM-CPE (Customer Premises Equipment) Service InterWorking Function

  10. Frame-Relay standard Multiservice devices can be connected to Frame-Relay routers which are consistent with IETF (Internet Engineering Task Force) RFC2427 (Request For Comments) standard: Encapsulation Frame-Relay IETF

  11. Frame-Relay DTE (Branch n.2) Frame-Relay DTE (Branch n.1) Frame-Relay nodes Frame-Relay DTE (Branch n.3) Frame-Relay DTE (Central Bank) Frame-Relay network

  12. DLCI = 232 DLCI = 564 DLCI = 1007 DLCI = 16 Frame-Relay DTE (Branch n.3) Frame-Relay DTE (Central Bank) Frame-Relay virtual circuits A logic connection between two Frame-Relay nodes is guaranteed by a virtual circuit namedDLCI (Data Link Connection Identifier)

  13. Frame-Relay DTE (Central Bank) Local Management Interface A Frame-Relay interface uses LMI protocol in order to check integrity connection and to give/receive information about the status of each DLCI Network (!!!) User (???) DLCI = 564 Frame-Relay network access node

  14. Application

  15. Case1: L2 Only N2 N2 CiscoWorks 20.20.20.254/24 11.11.11.2/24 10.10.10.2/24 V.35 S3026 20.20.20.2/24 WS5350 G.SHDSL Cisco GSR EoMPLS G.SHDSL 11.11.11.1/24 20.20.20.1/24 10.10.10.1/24 V.35 WS5350 NMS VLAN 920 N1 Traffic VLAN 910/911 (EoMPLS)

  16. Case2: L3 Only N2 CiscoWorks 20.20.20.254/24 12.12.12.1/24 V.35 S3026 20.20.20.2/24 WS5350 G.SHDSL 12.12.12.2/24 11.11.11.2/24 L3 MPLS VPN G.SHDSL 20.20.20.1/24 11.11.11.1/24 V.35 WS5350 NMS VLAN 920 N1 Traffic VLAN 910

  17. Installation

  18. Installation COMPUTER CONFIGURATION • Set the computer IP address at same segment of G.SHDSL MODEM. • The default IP address for G.SHDSL MODEM is 192.168.0.1. • The Subnet Mask is 255.255.255.0. • Set the IP address of the network card to one of the 192.168.0.2 - 192.168.0.254.

  19. Installation Start>Control Panel>Network Connections

  20. Installation Click Properties and choose Internet Protocol (TCP/IP)

  21. Installation Fixed IP address and subnet mask.

  22. Installation G.SHDSL MODEM CONFIGURATION • Open the browser; input http://192.168.0.1 Username: admin Password: admin

  23. Default Configuration Web Interface Username : admin Password : admin LAN Device IP Settings IP Address : 192.168.0.1 Subnet Mask : 255.255.255.0 DHCP Server DHCP Server : Disable Operation Mode Mode : Bridge mode

  24. Basic Configuration

  25. Basic Configuration

  26. Internet Setting Quick Set-up – Change from Bridge to Router mode

  27. Internet Setting VPI = 0, VCI = 35 Encapsulation : PPPoE PPP Username = xxx@xxx PPP Paasword = xxxxxxx NAT - Enable

  28. Internet Setting Connection status. Public IP for internet

  29. DHCP Setting Enable DHCP server choose Basic configuration > LAN DHCP Server : Enable Start IP Address: 192.168.0.32 End IP Address: 192.168.0.254

  30. DNS Setting Get DNS from BRAS or fix it.

  31. Save Configuration Tool > save

  32. Advance Configuration

  33. Advance Configuration Content • V.35 Application • Routing Function • Access list • Standard • DOS Protection • Virtual Server (Port Forwarding) • DMZ

  34. V.35 Application

  35. V.35 Application Quick Set-up – Change Operation Mode is Bridge mode. VPI = 0, VCI = 35

  36. V.35 Application Basic Configuration > Serial Port – Change clock source is internal. Internal Clock

  37. V.35 Application Advance Configuration > Frame Relay – Set LMI and DLCI LMI type : ansi/dce DLCI : 100

  38. Routing Function

  39. Routing Function Configuration at 5350 left side. • Operation Mode – Router • Service Type – COT • Standard Mode – ETSI (Annex B) • LAN IP address – 192.168.1.1/24 • VPI/VCI – 0/35 • Encapsulation – RFC 2684 • Local IP: 20.20.20.1/24 • Remote IP: 20.20.20.2

  40. Routing Function

  41. Routing Function Advance Configuration > Routing – Static Routing

  42. Routing Function Advance Configuration > Routing – Static Routing

  43. Routing Function Configuration at 5350 right side. • Operation Mode – Router • Service Type – RT • Standard Mode – ETSI (Annex B) • LAN IP address – 30.30.30.1/24 • VPI/VCI – 0/35 • Encapsulation – RFC 2684 • Local IP: 20.20.20.2/24 • Remote IP: 20.20.20.1

  44. Routing Function

  45. Routing Function Advance Configuration > Routing – Static Routing

  46. Routing Function Advance Configuration > Routing – Static Routing

  47. Routing Function Or enable RIP both 2 sides

  48. Application Advance

  49. Case1: L2 Only N2 N2 11.11.11.2/24 CiscoWorks 20.20.20.2/24 V.35 WS5350 G.SHDSL Cisco GSR EoMPLS G.SHDSL 20.20.20.1/24 V.35 WS5350 N1 10.10.10.1/24

More Related