1 / 50

Energy Management Opportunities for Residential Property Managers

Energy Management Opportunities for Residential Property Managers. Your Presenters. Welcome: Jim Grossman, Business Customer Services Technologies: Mike Carter and Mark Farrell, Energy Engineers

torie
Télécharger la présentation

Energy Management Opportunities for Residential Property Managers

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Energy Management Opportunities forResidential Property Managers

  2. Your Presenters • Welcome: Jim Grossman, Business Customer Services • Technologies:Mike Carter and Mark Farrell, Energy Engineers • Energy Efficiency Programs: Greg Stiles, Programs Manager

  3. Energy Management Benefits • Bottom line cost savings today! • Energy • Maintenance • Tenant comfort, satisfaction and retention Source: stock.xchng

  4. Energy Management Opportunities • Energy Basics • Insulation • Demand Reduction • HVAC • Lighting • Heating Systems • Incentives

  5. Energy Basics • Demand versus Energy • Kilowatt (kW) is a measure of demand—similar to the speedometer of your car that records the rate at which miles are traveled • A bigger engine is required to travel at a faster rate • Peak power demand is usually measured as an average over a 15-minute period • Spikes and surges from motor startup and other short-term anomalies have little influence on peak demand • Kilowatt-hour (kWh) is a measure of energy/consumption—similar to the odometer on your car which measures miles traveled Source: stock.xchng Source: Commonwealth of Kentucky

  6. Energy Basics • Demand versus Energy • Energy Cost = Energy Consumption x Unit Cost = kWh x $/kWh • A 113-Watt four-lamp light fixture costs about $66 annually when operating 16 hr/day (113 W x 5,840 hr x $0.10/kWh ÷ 1,000 W/kW) • Motor power (kW) = Horsepower (HP) x 0.746/efficiency • A 10 HP motor = 10 HP x 0.746/0.90 = 8.3 kW • A 10 HP motor costs about $4,850 annually (8.3 kW x 5,840 hr x $0.10/kWh) when operating 16 hr/day • Pay the price for improved energy efficiency! • The operating cost over the lifetime of a motor or light fixture can far exceed the original purchase price

  7. Insulation • Insulation has diminishing returns • R-value is resistance to heat flow (additive) • R-7 + R-21 = R-28 (4 times R-7, and 75% better than R-7) • R-7 + R-49 = R-56 (8 times R-7, but only 12% better than R-28!) • U-value is conductance of heat; inverse of R-value • U(R-7) = 1/7 = 0.143 • U(R-21) = 1/21 = 0.048 • U(R-56) = 1/56 = 0.018 (87% less than R-7) • U(R-28) = 1/28 = 0.036 (75% less than R-7)

  8. Insulation • Sources of Loss • 45% walls • 35% roof • 20% windows, doors, cracks

  9. Insulation • High Performance Windows • Energy savings of 6% to 8% is typical; 3 year paybacks • Solar Heat Gain Coefficient (SHGC) radiation; 0 to 1; <0.55 is good • U-Factor heat conductance; 0.2 to 1.2; <0.40 is good • Vinyl material and inert gas lowers U-Factor • Argon gas 35% lower than air; Vinyl 80% less than aluminum • Visible Transmittance (VT); 0 to 1; >0.60 is good • Air Leakage (AL); 0.1 to 0.3 cfm/ft²; optional rating • Window films; tinted $4 to $6/ft² or spectrally selective $9 to $12/ft²

  10. Insulation • Foliage Saves Energy • Deciduous trees • Block solar radiation in the summer • Reduce light glare • Act as a windbreak to decrease air infiltration • Provide some evaporative cooling of surrounding air • Reduce carbon footprint • Green roofs • Include a waterproofing membrane, and are partially (or completely) covered with a growing medium such as vegetation and soil • Up to 25% reduction in summer cooling load • Reduce storm runoff • Improve sound insulation • Up to 2X roof life

  11. Demand Reduction Ideas • Lighting • Turn off lights in unoccupied or day lighted rooms • Turn off display and decorative lighting • Reduce corridor lighting • Use occupancy sensors in low-traffic areas • HVAC • Allow cooling season space temperatures to rise as high as 78°F • Ensure that ventilation grilles and fan coil units are not blocked by books, flowers, debris, or other obstructions

  12. Demand Reduction Ideas • Office Equipment • Activate ENERGY STAR® power-down features • Use SmartStrips to completely remove power from printers and copiers • Restrict use of personal appliances, such as coffee pots, refrigerators, and heaters • Turn off or unplug chilled-water drinking fountains • Other • Convert your roof to a reflective surface • Shut off selected elevators • Consider variable speed motors for fans and pumps • Lower hot water setpoint from 140°F to 120°F

  13. Corporate Energy Management • Key Components of Energy Management • Commitment by owners and management • Clearly stated goals on energy efficiency and waste reduction, • Delegation of responsibility and accountability • Sustained tracking and assessment of energy use and technology application • Continuous investigation of potential energy projects • Our Business Solutions Toolkit offers free energy-efficiency posters for your business

  14. HVAC

  15. HVAC • Efficiency Metrics • One ton (12,000 Btu/hr) equals 3.516 kW at 100% efficiency • Coefficient of Performance (COP) • COP = Rated Cooling Output, kBtuh / Rated electrical input, kBtuh • Full Load Value (FLV) • FLV = kW/ton • COP = 3.516 (kW/ton) / FLV efficiency rating (kW/ton) • Energy Efficiency Ratio (EER) • EER = Cooling output (Btuh) / Electricity consumed (watt) • Outdoor air at 95ºF and 40% RH • EER = 12,000 Btu per ton / FLV (watt per ton) • EER = COP x 3.413 • Seasonal Energy Efficiency Ratio (SEER) • Minimum 15 SEER recommended • Heating Seasonal Performance Factor (HSPF) • Minimum 8.0 HSPF recommended

  16. HVAC • Temperature Setback/Setforward • Save 3% per °F per 24 hr • 72°F  68°F ( 4°F) for 12 hr saves 6% • Obtain Proper Humidity Control • In the Summer, decrease relative humidity (RH) to feel cool. • Operation at 78°F / 40% RH provides the same level of occupant comfort as 74°F / 50% RH does. • 74°F  78°F setforward for 24 hr saves 10% to 12% • Remove moisture with desiccant or enthalpy/heat wheel • Relative humidity >70% with temperature >70°F can encourage mold growth! • In the Winter, opposite applies–raise RH to feel warm. • Add moisture with evaporative humidifier • Ultrasonic humidifiers require filtered water Source: ENERGY STAR

  17. HVAC Source: General Electric • Variable Speed Drives/Adjustable Speed Drives/Electrically Commutated Motors (ECM) • Best for variable torque loads often found in variable flow applications (pumps and fans) and greater than 2,000 hours operation • Horsepower varies as the cube of speed/flow • Cut speed/flow by 50% and you cut energy consumption by nearly 90%! (0.5 x 0.5 x 0.5 = 0.125) • 50% to 60% energy savings for HVAC applications • Converts 60 Hz to 120-400 Hz in pulse width modulation • Might run at full load 40% of the time and half speed 60% of the time. • Not as efficient at 100% rated speed

  18. HVAC • Upgrade older HVAC (10 to 15 years) • Chillers: 0.8 kW/ton  0.5 kW/ton (37% less!) • Unitary rooftop: 1.5 kW/ton  1.2 kW/ton (20% less!) Source: courtesy of McQuay International

  19. HVAC Source: Charles Linn, Architectural Record • Air-Source Heat Pumps • Uses the vapor-compression cycle to pump heat uphill—from a lower temperature to a higher temperature.

  20. Image courtesy of ECS Geothermal HVAC • Geothermal or Water-Source Heat Pump • Takes advantage of underground temperatures that range from 45°F (7°C) to 75°F (21°C) year round. • Roughly 30% savings compared to AC/Boiler or AC/Furnace combo • Geothermal requires higher capital investment and much real estate • New construction accommodates verticals and pond loop

  21. Image courtesy of Coil-Tech HVAC • Coil Cleaning • Most commercial HVAC units have multiple coilsstacked or sandwiched together. • Outdoor condenser coils lose less performance with blockage than indoor evaporator coils. • If the evaporator airflow of a 3-ton rooftop unit is restricted by 36%, the capacity drop is 19.4%. • This changes the 3-ton unit to a 2.5-ton unit. • On the other hand, when the condenser coils are 56% restricted, the capacity drops only 10.9%. • Blocked condenser coils can increase condensing temperature by 8°F to 10°F resulting in a 6% to 8% increase in power consumption. • You can check coil performance by measuring the air temperature drop across the coils. • Larger temperature drops of 30ºF or higher indicate that a coil cleaning is in order. • You can also measure supply-fan amperage or filter/coil pressure drop (with fresh filters) and compare this data against last year's readings.

  22. Lighting

  23. Lighting • Lumens—A measurement of the perceived power of light. • 60-watt incandescent ~ 850 lumens (100 CRI) ~ 14 lpw efficacy • 32-watt T8 fluorescent ~ 2,800 lumens (83 CRI) ~ 88 lpw • 400-watt metal halide ~ 24,000 lumens (65 CRI) ~ 60 lpw • 400-watt high-pressure sodium ~ 45,000 lumens (22 CRI) ~ 112 lpw • Color Rendering Index (CRI)—A measurement of a light source's ability to render colors the same as sunlight does. • CRI describes to what degree the light spectrum source is “filled out” 65CRI 92CRI

  24. Lighting Source: PHOTOWORKSHOP.COM • Color Temperature—The apparent/perceived color of a light source compared to the color appearance of an ideal incandescent light source at a particular temperature, expressed in degrees Kelvin (K). • <3,200 K is “visually warm” or red/yellow (good for reading) • Incandescent ~2,800 K • >4,000 K is “visually cool” or blue (good for inspection) • Sunlight ~5,500 K

  25. Lighting Source: Philips Lighting • New Halogen Bulbs • Up to 30% energy savings • Instant on • No mercury • 100 CRI • Compliance with EISA 2007 • Philips Halogena® Energy Saver/Energy Advantage (3,000 hrs) • Sylvania Halogen SuperSaver® (1,000 hrs) • GE Edison™ (2,500 hrs)

  26. Lighting • Replace existing T12 fluorescent lamps with T8 fluorescent lamps (up to 30% savings) • NEMA Premium® Ballasts • A 5% to 7% efficiency improvement (2 to 5 watts) and anti-striation • Programmed start (in series) • Long preheat shuts down after start (up to 50,000 cycles) • Rapid start (in series) • Simultaneous preheat stays on all the time (15,000 to 20,000 cycles) • Instant start (in parallel) • No-preheat; high-voltage start (10,000 to 15,000 cycles) • Not good with occupancy sensors (<30 minute burn)

  27. Lighting • Compact Fluorescent Lighting (CFL) • Advantages over incandescent • The same or more light output (lumens) • A 75% energy reduction • Over six times the rated life! • Energy savings far outweigh the difference in lamp price • Use reflector flood CFLs in recessed-can lights • Consider aluminum reflector CFL PAR lamps. • Issue of mercury content can be addressed • Single, double (T), triple (TR), quadruple (Q) twin-tube (turns) • Twister • Globes • Candelabra Source: NREL

  28. Lighting • Light Emitting Diodes (LEDs) • Heat loss in LEDs is through conduction, not radiation • Heat is the enemy of performance for LEDs • Typically 110°F maximum ambient temperature limit • Enhanced by cold temperatures • Excessive heat and cold diminish fluorescent performance • Frequent switching does not affect rated life for LEDs as it does for fluorescents • Directional nature of LED results in very high luminaire efficacy Incandescent90% heat; 10% light Compact fluorescent 20% heat; 80% light LED 20% heat; 80% light Source: ENERGY STAR

  29. Lighting *At 40% fluorescent rated life; 70% to 90% at 50,000 hours • Comparison with traditional lighting • Very compact and low-profile • Nothing to “break” • No abrupt failure mode • Instant on (no warm-up time required)

  30. Lighting Source: GE Lighting Source: LEDzworld LED Omnidirectional Replacement Lamps

  31. Lighting • Accent lights • Step and path lighting • Cove lighting • Spaces with occupancy sensors • Food preparation areas Source: EERE • Best LED Applications • Exit signs • Undercabinet lighting • In-cabinet accent lighting • Adjustable task lighting • Outdoor area lighting • Recessed downlights • Art display lighting

  32. Lighting • Exit Signs • Annual cost of ownership for LED exit signs is much less than for fluorescent exit signs Incandescent Fluorescent LED Sources: Stock Exchange and DOE

  33. Lighting • Occupancy Sensors • $30 to $150 cost (2 year payback) • Can shorten life of fluorescents with instant start ballast • Passive Infrared (PIR) Sensors • Are based on differences in heat emitted by humans in motion • Require a line of sight and are most sensitive to lateral movement • Are most suitable for smaller, enclosed spaces, such as hallways • Have a maximum coverage area of 1,000 ft2 • Ultrasonic Sensors • Use the Doppler principle • Can “see” around corners • Are most sensitive to movement to and from the sensor • Are most suitable for open spaces, spaces with obstacles, restrooms, and spaces with hard surfaces • Have a maximum coverage area of 2,000 ft2

  34. Lighting • Day Lighting • Skylights/lightpipes, clerestory windows, and roof monitors • Energy savings can range from about $0.25/ft2 to $0.50/ft2, depending on the building type, location, office area plan, and local cost of energy • Photosensor layout is important. • Daylight is BIG! • Foot-candles varies by 2X between summer and winter • Diffuse most of it (5% to 10% direct sunlight maximum) • Do not try to match daylight to electric light (confuses people) • About 3% to 4% of roof area is optimal for energy savings Source: NREL

  35. Lighting • Outdoor and security lighting • Mainly metal-halide and high-pressure sodium • Should be 1 to 3 fc (foot-candles) at ground level • Safety, security, and productivity • DO NOT try to illuminate multiple areas with just one fixture! • Controls save energy • Daylight controls, or photo sensors • Whenever adequate daylight is available • Timer switches • Turn on lights for only short duration • Motion sensors • Turn on lights, or turn up lights that have been dimmed, whenever an occupant is present LED (left) vs HPS (right) Source: Beta Lighting & EERE

  36. Heating Systems

  37. Heating Systems • Measuring Boiler Efficiency • Fuel-to-steam efficiency is the best efficiency metric • Boiler output (Btu)/boiler input (Btu) • Accounts for both combustion and thermal efficiency, radiation, and convection losses • Efficiency mainly influenced by boiler design • Number of passes more important than add-on (turbulator) • Burner/boiler compatibility (accounts for geometry, heat transfer, and so on) • Burner controls (independent control of fuel and air is best) • Heating surface (square feet/boiler HP; 5 ft2/HP is desired) • Other factors • Flue gas temperature directly correlates with efficiency • Fuel hydrogen/carbon ratio (fuel oil > natural gas) • Excess air (10% to 12%) • Ambient temperature (every 40°F ~ 1% efficiency change)

  38. Heating Systems • Proper BoilerAir:Fuel Ratio • Efficiency improvements • 82.8%  85.4% = 2.6% • 68.2%  76.0% = 7.8% Source: Gas Technology Institute

  39. Heating Systems • Insulate steam pipeswith at least ½" insulation • For a 350°F process steam pipe, savings are $5,000 for 2" dia. and $10,000 for 4" dia. pipe • Diminishing returns for insulation thickness > ½"

  40. Heating Systems (Source: courtesy of Viessmann, 1: gas burner; 2: heat exchanger surface; 3: control unit) • Condensing Boilers • Efficiencies of 88% to 95% • Captures the additional latent heat released from condensing flue gas (up to 12% to 13% of the original energy content of the gas). • Reduces flue gas temperature from 250°F to 350°F (120°C to 180°C) to around 130°F (55°C). • Return water must be below approximately 140°F. • Radiant floor heating, swimming pool and spa heating, and facility hot water heating are good applications.

  41. Heating Systems • Tankless Water Heaters • $650 to $1,000 for a tankless design versus $300 for tank • 10% to 30% more energy efficient • Requires 20 kW to 100 kW of power capacity • 250 to 500 amp service • Three factors that favor tankless • Significant periods of non-use • Required flow rates are less than 6 gal/minute with a temperature rise of 80°F to 90°F • When first cost is less important than total life cycle costs Source: Takagi

  42. Heating Systems Source: Andy Walker, NREL • Solar Thermal Hot Water • Active • Passive • Direct (Open Loop) • Indirect (Closed Loop)

  43. Heating Systems Source: Renewable Energy Inc. • Solar Thermal Sample Economic Justification • 40 ft2 evacuated tube array $7,000 installed cost (market price) - $2,100 Federal incentive (30%) - $2,500 State incentive $2,400 expense • 83 gallons of hot water per day at 120⁰F • 83 gal x 8.34 lb/gal x (120F-60F) x 1 Btu/lbF = 41,530 Btu • 41,530 Btu/day or 15,160,000 Btu per year • Equivalent annual electric costs (at $0.08/kWh) = $385 • Equivalent annual gas costs ($1/therm) = $240 • Simple payback of 6 to 10 years • NPV of $967 and IRR of 13% for 7% cost of capital and 15 year life for electric case

  44. Heating Systems Source: DOE • Swimming Pool Energy Conservation • Solar thermal water heating • 80% of installed solar thermal capacity is for pool heating • 1,000 Btu per panel square foot per day • Reduce evaporation losses • Pool covers save 50% to 70% • Create windbreaks from trees, shrubs, or fences • Optimize pump systems • High-Efficiency Pumps • Water Circulation: Reduce Pump Operating Time • Use timers to achieve short cycles

  45. The Business Solutions Toolkit • Links found on the Pacific Power website • Can access direct at pacificpower.net/toolkit • Register to use the Toolkit and you will receive our monthly e-mail newsletter

  46. What is in the Toolkit

  47. Online Business Tools www.pacificpower.net/toolkit

  48. Home Energy Savings Program • Incentive program for Pacific Power residential customers • Cash back to customers who purchase and install qualified energy-efficient equipment and services • Appliances • ENERGY STAR light fixtures and ceiling fans • Specially priced CFLs at Participating Retailers • Heating and cooling equipment/services • Windows and insulation (available in Washington) • Incentives available if you manage multifamily units

  49. Energy Trust of Oregon Programs • Existing multifamily complexes • Energy Trust helps multifamily property owners reduce the cost of energy-efficiency projects by offering cash incentives to contractors or their customers for completing energy efficiency projects • Incentives are currently available for: • insulation • windows • exterior doors • lighting • HVAC improvements • water heating • clothes washers • dishwashers • refrigerators

  50. Contacts • For more information please phone us: • Call yourBusiness Solutions Team for answers to service and account questions at 1-866-870-3419 • Visit our website at: • Efficiency programs and incentives Web page – pacificpower.net/wattsmart • Business Solutions Toolkit – pacificpower.net/toolkit • Or contact us directly: • E-mail us at energy.expert@pacificorp.com • Use our online inquiry form – pacificpower.net/inquiry • Call our Customer Hotline at 1-800-942-0266 • Also visit the Energy Trust of Oregon website at energytrust.org © 2009 Tech Resources Inc.

More Related