1 / 38

D. Attié

Beam tests of a Micromegas Large TPC Prototype. D. Attié. SINP, January 22 th , 2010. Overview. Introduction, technological choice for ILC-TPC The Large TPC Prototype for ILC Bulk Micromegas with resistive anodes Beam test conditions, T2K electronics Data analysis results:

xanthus-mcmillan
Télécharger la présentation

D. Attié

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Beam tests of a Micromegas Large TPC Prototype D. Attié SINP, January 22th, 2010 WP meeting 94

  2. Overview Introduction, technological choice for ILC-TPC • The Large TPC Prototype for ILC • Bulk Micromegas with resistive anodes • Beam test conditions, T2K electronics • Data analysis results: • Drift velocity • Pad response function • Resolution • Comparison between two resistive modules • Future plans: • Pixelized Micromegas module • Integrated electronics for 7 modules Conclusion SINP seminar ̶ January 22th, 2010

  3. How to improve the spatial resolution? • Need for ILC: measure 200 track points with a transverse resolution ~ 100 μm • - example of track separation with 1 mm x 6 mm pad size: •  1,2 × 106 channels of electronics • sz=0 > 250 μm amplification avalanche over one pad • Spatial resolution σxy: • - limited by the pad size (s0 ~ width/√12) • - charge distribution narrow (RMSavalanche ~ 15 μm) Calculation for the ILC-TPC •  1. Decrease the pad size: narrowed strips, pixels • + single electron efficiency • need to identify the electron clusters 55 mm D.C. Arogancia et al., NIMA 602 (2009) 403 1. Pixels • 2. Spread charge over several pads: resistive anode • + reduce number of channels, cost and budget • + protect the electronics • limit the track separation • need offline computing 2. Resistive anode SINP seminar ̶ January 22th, 2010

  4. Large TPC Prototype for ILC • Built by the collaboration LC-TPC • Financed by EUDET • Located at DESY: 6 GeV e- beam • Sharing out : • - magnet: KEK, Japan • - field cage: DESY, Germany • - trigger: Saclay, France • - endplate: Cornell, USA • - Si envelope: OAW, Austria • - laser: Victoria U., Canada • - Micromegas: Saclay, France, Carleton/Montreal U., Canada • - GEM: Saga, Japan • - TimePix pixel: F, G, NL SINP seminar ̶ January 22th, 2010

  5. Large TPC Prototype for ILC SINP seminar ̶ January 22th, 2010

  6. Large TPC Prototype for ILC • 60 cm long TPC • Endplate ø = 80 cm of 7 interchangeable panels of 23 cm •  to fit in 1T superconductingmagnet 24 rows x 72 columns <pad size> ~ 3x7 mm2 80 cm SINP seminar ̶ January 22th, 2010

  7. Module presently avalaible 2 Resistive Kapton ~1 MΩ/□ Resistive Kapton ~4 MΩ/□ Standard Resistive ink ~1 MΩ/□ SINP seminar ̶ January 22th, 2010

  8. Beam test conditions at B=1T • Bulk Micromegas detector: 1726 (24x72) pads of ~3x7 mm² • AFTER-based electronics (72 channels/chip): • low-noise (700 e-) pre-amplifier-shaper • 100 ns to 2 μs tunable peaking time • full wave sampling by SCA • Beam data (5 GeV electrons) were taken at several z values by sliding the TPC in the magnet. Beam size was 4 mm rms. • frequency tunable from 1 to 100 MHz (most data at 25 MHz) • 12 bit ADC (rms pedestals 4 to 6 channels) 6 FECs and 1 FEM in its shielding SINP seminar ̶ January 22th, 2010

  9. Determination of z range • Cosmic run at 25 MHz of sampling frequency  time bin = 40 ns • Drift velocity in T2K gas (Ar/CF4/iso-C4H10, 95/3/2) at 230 V/cm: • TPC length = 56.7 cm agreement with survey 220 time bins SINP seminar ̶ January 22th, 2010

  10. Pad signals: beam data sample • RUN 284 • B = 1T • T2K gas • Peaking time: 100 ns • Frequency: 25 MHz SINP seminar ̶ January 22th, 2010

  11. Two-track separation φ r z SINP seminar ̶ January 22th, 2010

  12. Drift velocitymeasurement • Measured drift velocity (Edrift = 230 V/cm, 1002 mbar): 7.56 ± 0.02 cm/s • Magboltz: 7.548 ± 0.003 cm/sin Ar/CF4/iso-C4H10/H2O (95:3:2:100ppm) B = 0T SINP seminar ̶ January 22th, 2010

  13. Determination of the Pad Response Function  Pad pitch • Fraction of the row charge • on a pad vsxpad – xtrack • (normalized to central pad charge) • Clearly shows charge spreading • over 2-3 pads • (data with 500 ns shaping) • Then fit x(cluster) using this • shape with a χ² fit, • and fit simultaneously all lines xpad – xtrack (mm) See Madhu Dixit’s talk xpad – xtrack (mm) SINP seminar ̶ January 22th, 2010

  14. Spatial resolution • Resolution at z=0: σ0 = 54.8±1.6 mwith 2.7-3.2 mm pads (wpad/55) • Effective number of electrons: Neff = 31.81.4 consistent with expectations SINP seminar ̶ January 22th, 2010

  15. Field distortion measurement using laser • Two laser devices installed on the endplate to light up photosensitive pattern • on the cathode (spots and line) • Deterioration of resolution at z > 40 cm : due to low field 0.9 to 0.7 T • in the last 20 cm (significant increase of transverse diffusion) Photoelectrons from the cathode pattern B field map of the magnet 50 cm 30 cm 5 cm Beam position SINP seminar ̶ January 22th, 2010

  16. Description of the resistive anodes Resistive Kapton ResistiveInk Resistive Ink Resistive Kapton Prepreg Prepreg PCB PCB SINP seminar ̶ January 22th, 2010

  17. Comparison at B=1T, z ~ 5 cm ResistiveKapton ResistiveInk • RUN 310 • Vdrift= 230 cm/s • Vmesh = 380 V • Peaking time: 500 ns • Frequency Sampling: 25 MHz • RUN 549 • Vdrift = 230 cm/s • Vmesh = 360 V • Peaking time: 500 ns • Frequency Sampling: 25 MHz SINP seminar ̶ January 22th, 2010

  18. Pad ResponseFunctions, z ~ 5 cm ResistiveInk ResistiveKapton xpad – xtrack(mm) xpad – xtrack(mm) Γ² = 7 mm Γ² = 11 mm δ = 10 mm δ= 13 mm xpad – xtrack(mm) xpad – xtrack(mm) σz=5 cm = 68 µm σz=5cm = 130 µm ! SINP seminar ̶ January 22th, 2010

  19. 2.2 GeVMomentum • B=1T • Beam energy set to 2.2 GeV using one module in the center • Simple Landau fit  MPV = 2.2 GeV SINP seminar ̶ January 22th, 2010

  20. Tests with Si envelope (nov. 2009) From Vienna Si Si SINP seminar ̶ January 22th, 2010

  21. Synchronized events with Si envelope Resistive Ink TLU Resistive Kapton SINP seminar ̶ January 22th, 2010

  22. Description of the TimePix chip 55 mm m μ 14080 m (pixel array) 55 4 4 16120 m 55 mm 2 2 3 3 1 1 5 5 55 μ m 14111 m • Chip (CMOS ASIC) upgraded in the EUDET framework from the Medipix chip developed first for medical applications • IBM technology 0.25 m • Characteristics: • surface: 1.4 x 1.6 cm2 • matrix of 256 x 256 • pixel size: 55 x 55 μm2 • For each pixel: • preamp/shaper • threshold discriminator • register for configuration • TimePix synchronization logic • 14-bit counter • Noise: ~ 650 e- • Cin ~ 15 fF Pixel Synchronization Logic Interface Configuration latches Preamp/shaper Counter THL disc. SINP seminar ̶ January 22th, 2010

  23. TimePix synchronization logic control Medipix Mode Timepix Mode TOT Mode not detected detected Charge summed • Each pixel can be configured independently in 5 different modes • Internal clock up to 100 MHz 100 MHz Internal shutter Shutter Internal clock 10 ns Digital signal Analog signal SINP seminar ̶ January 22th, 2010

  24. Micro-TPCTimePix/Micromegas Windows for X-ray sources • Micro-TPC with a 6 cm height field cage • Size : 4 cm × 5 cm × 8 cm • Read out by MUROS or USB1.2 devices • Two detectors are available now at Saclay Cover Windows for β sources Field cage 6 cm Micromegas mesh TimePix chip SINP seminar ̶ January 22th, 2010

  25. Micro-TPCTimePix/Micromegas: Time mode • TimePix chip • + SiProt 20 μm • + Micromegas • 55Fe source • Ar/Iso (95:5) • Time mode • z = 25 mm • Vmesh = -340 V • tshutter = 283 μs SINP seminar ̶ January 22th, 2010

  26. Micro-TPCTimePix/Micromegas: Time mode • TimePix chip • + SiProt 20 μm • + Micromegas • 90Sr source • Ar/Iso (95:5) • Time mode • z ~ 40 mm • Vmesh = -340 V • tshutter = 180 μs SINP seminar ̶ January 22th, 2010

  27. 2×4 TimePix/InGrid matrix module • Mother card • Mezzanine card • Guard ring card • Heat dissipation block SINP seminar ̶ January 22th, 2010

  28. Further tests for resistive bulk Micromegas Resistive technology choice In 2008/2009 with one detector module In 2010/2011 with 7 detector modules Reduce the electronics to fit to the module and power consumption SINP seminar ̶ January 22th, 2010

  29. 7-modules project FEC FEM PCB detector (bottom) SINP seminar ̶ January 22th, 2010

  30. 7-modules project SINP seminar ̶ January 22th, 2010

  31. 7-modules project • Remove packaging and protection diodes • Use 2 × 300 pins connector • Replace resistors SMC 0603 by 0402 (1 mm × 0.5 mm) 25 cm FEC 12,5 cm 4,5 cm 14 cm 2,8 cm 3,5 cm 0,78 cm 3,5 cm Chip 0,74 cm SINP seminar ̶ January 22th, 2010

  32. Conclusions • Three Micromegas technologies with resistive anode have been tested within the EUDET facility using 1T magnet to reduce the transverse diffusion • C-loaded Katpon (4 MΩ/□) technology gives better results than resistive ink technology • Data analysis results confirm excellent resolution at small distance with the resistive C-loaded Kapton (4 MΩ/□): 55 m for 3 mm pads • Data analysis of laser tests and the second resistive C-loaded Kapton (1 MΩ/□) should be done soon. • Plans are to test several resistive layer manufacturing process and capacitance/resistivity, then go to 7 modules with integrated electronics by the end of this year SINP seminar ̶ January 22th, 2010

  33. Dhanyavad SINP seminar ̶ January 22th, 2010

  34. Backup slides SINP seminar ̶ January 22th, 2010

  35. TimePix chip architecture • Clock per pixel up to 100 MHz • Characteristics: • analog power: 440 mW • digital power (Ref_Clk = 80 MHz): 450 mW • serial readout (@ 100 MHz): 9.17 ms • parallel readout (@ 100 MHz): 287 μs • > 36 M transistors on 6 layers • Pixel modes: • masked • counting mode (Medipix, Timepix-1h) • Time-Over-Threshold  “charge” info • Common stop  “time” info SINP seminar ̶ January 22th, 2010

  36. TimePix chip schematic Previous Pixel For each pixel Ref_Clkb Clk_Read Mux 4 bits thr Adj Mask Mux Preamp Input Disc 14 bits Shift Register Shutter THR Timepix Synchronization Logic Shutter_int Ctest P0 Conf Testbit Polarity P1 8 bits configuration Test Input Ovf Control Ref_Clk Clk_Read Next Pixel Digital part Analogic part SINP seminar ̶ January 22th, 2010

  37. Readout system for Medipix/TimePix chip • MUROSv2.1: • Serial readout • VHDCI cable of length <3m • read 8 chips in mosaic • tunable clock [30-200MHz] • ~40fps @160MHz • http://www.nikhef.nl/pub/experiments/medipix/muros.html • USB: • Serial readout • ~5 fps@20MHz • http://www.utef.cvut.cz/medipix/usb/usb.html • Mosaic achitecture: SINP seminar ̶ January 22th, 2010

  38. Detectors using Medipix2/TimePix chip + - Single pixel readout cell + + - - Solid detector Gas detector x, y, F(x, y) x, y, z(t), E(x,y) Drift grid X-ray source Ionizing particle Gas volume Semiconductor sensor Flip-chip bump bonding connections Amplification System (MPGD) Medipix2/TimePix chip Medipix2 chip SINP seminar ̶ January 22th, 2010

More Related