1 / 22

Work Review

Work Review. Angel Monera Martinez. Index. Objectives Time Frame Analog Link Analog Requirements Miteq Characterization and tests Digital Link Requirements Laser and photodiode Tests and results The prototypes (test and results) Software Developed Test Beam & Link Validation Pricing

ernst
Télécharger la présentation

Work Review

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Work Review Angel Monera Martinez

  2. Index • Objectives • Time Frame • Analog Link • Analog Requirements • Miteq Characterization and tests • Digital Link • Requirements • Laser and photodiode Tests and results • The prototypes (test and results) • Software Developed • Test Beam & Link Validation • Pricing • Review and Conclusions • Bibliography • Acknowledgments • Request and questions

  3. Objectives • Develop an Analog Optical Link for the AB/RF Group • Develop a Digital Optical Link • Develop the links and leave them ready for the test beam • Help to install the links and crates in the PCR and experiments

  4. Timeframe Forecast Definitive Version Definitive Version Timeframe Followed Timeframe Blue: Analog Link Green: Digital Link Yellow: AB/RF Validation or test

  5. Analog Link (Requirements) • Use the AB/RF Miteq Lasers/Photodiodes • Capability of Monitoring Photodiode and Laser • Pluggable in standard crates/racks  VME interface • Heat Sink required • Firmware development in Visual Elite… • … Using the VME code provided by AB/RF

  6. Analog Link (Miteq Characterization) • Tests done in collaboration with AB/RF Group… • …Over two test board with temperature sensors • Tests: • Temperature Vs Gain tests were developed in a climatic chamber • Bandwidth • Phase noise @400, 40 and 10 (MHz)

  7. Analog Link (Test's Results) • From Temperature test were known: • Heat sink + air flow •  Ideal conditions @ 25-30Deg (~8dB gain) • Air flow or heat sink •  extreme work conditions@40-50Deg (~1dB lost@) • No heat sink / No airflow •  Laser and photodiode break down >60Deg • From bandwidth test were known: • Bandwidth from 30KHz to 3GHz • There is an Internal AGC • The output signal is inverted.

  8. Analog Link (Test's Results) • From Phase Noise tests were obtained: • (Table) • Low noise but higher than the old Miteq used • Noise contain high 50Hz Component. (eliminating this component the noise values are reduced around 50%)

  9. Analog Link (The Prototype Boards)

  10. Digital Link (Requirements) • Same architecture as Analog • Same or close to analog performance • Increase monitoring capability • Frequency Detection • Power Monitoring & Signal detection • Laser Enable / Disable • No Heat Sink • Firmware development in Visual Elite… • … Using the VME code provided by AB/RF

  11. Digital Link (Lasers) • 3 Digital Lasers were tested (and compared with the analog) • OCP STX 03 (155MHz) • OCP STX 24 (1.2GHz) • PHOTON MT5 343 ( obsolete 155MHz ) • As Results: • OCP 24 Better skew and s2s from low freq. to 40MHz • OCP 03 Better for skew@400MHz (out of range)

  12. Digital Link (Photodiodes) • Digital photodiode were tested • OCP SRX 03 (155MHz) • OCP SRX 24 (1.2GHz) • TRUELIGHT TRR (155MHz) • OKI OF363B-C3 • LDI LPA 1000PT-D & LDI LPA 1000PT-D v2 • JDSU EDR515D • As Results: • OCP 24: Better for 400 and 10 MHz • Truelight: Better for 40MHz and pulse reception

  13. Digital Link (Prototype Boards)

  14. Software • A few interface were written to control The boards: • VME Monitor for Windows and Linux in C/C++ • Read Monitor (Tcl/Tk): Generic Reader • Write Monitor (Tcl/Tk): Generic Writer • ReadRXD: Control Rx_D board • ReadTXD: Control Tx_D board • ReadRFA: Control RF_RX/TX_A boards • Scan: Detect the RF boards in a crate

  15. Software (Screenshots)

  16. Test Beam and Link Validation • Link tested in lab: Digital and analog links works in similar way and better than the old TTC system • In the Test Beam (Sep 2006), in a real scenario, the Analog works more stably than the digital and the old TTC system (TTCRD12 & TTCmi)

  17. Pricing • The Digital Link is 4 times cheaper than the Analog link

  18. Review - Conclusions • All the prototype boards and software developed are working and have been validated by the ESS/TTC and by the AB/RF group • The digital boards need some changes that will improve their performance (changes that will be done for production)

  19. Acknowledgments • Too many people to say thanks.. Specially to: • Sophie Baron to help me in the project and choose me between the “thousands” of applications… • Christopher Parkman and Mike Clayton: to let me work in their group and “tolerate” my network problems • AB/RF group in specially to Philippe Baudrenghien to show me the Analog side of the things • And to all the ESS Group to accept me like one more in the group

  20. Bibliography (Docs Writen) • Boards user manuals • 3 User manuals were written • RF_A (RF_RX/TX_A boards) • RF_RX_D Board • RF_TX_D Board • Programming user manual • 5 Software manual were written • Generic Readers • Specific TCL/TK applications for each board • Lasers and photodiode evaluation report • Publication with Sophie Baron in the book of the workshop’s conference

  21. Questions?

  22. Many Thanks Merci Danke Thanks Ringraziare  Obrigado Gracias 

More Related