1 / 18

Unit 11 Latches and Flip-Flops

Unit 11 Latches and Flip-Flops. Ku-Yaw Chang canseco@mail.dyu.edu.tw Assistant Professor, Department of Computer Science and Information Engineering Da-Yeh University. Outline. 11.1 Introduction 11.2 Set-Reset Latch 11.3 Gated D Latch 11.4 Edge-Triggered D Flip-Flop 11.5 S-R Flip-Flop

gezana
Télécharger la présentation

Unit 11 Latches and Flip-Flops

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Unit 11Latches and Flip-Flops Ku-Yaw Chang canseco@mail.dyu.edu.tw Assistant Professor, Department of Computer Science and Information Engineering Da-Yeh University

  2. Outline 11.1 Introduction 11.2 Set-Reset Latch 11.3 Gated D Latch 11.4 Edge-Triggered D Flip-Flop 11.5 S-R Flip-Flop 11.6 J-K Flip-Flop 11.7 T Flip-Flop 11.8 Flip-Flops with Additional Inputs 11.9 Summary Latches and Flip-flops

  3. Introduction • Sequential switching circuits • The output depends on • Present input • Past sequence of inputs • ‘remember’ something about the past history of the inputs • Two commonly used memory devices in sequential circuits • Latches – no clock input • Flip-flops Latches and Flip-flops

  4. Feedback • The output of one of the gates is connected back into the input of another gate in the circuit so as to form a closed loop. • The rate at which the circuit oscillates is determined by the propagation delay in the inverter. Latches and Flip-flops

  5. Two Inverters witha Feedback Loop • Two stable conditions • Often referred to as stable states Latches and Flip-flops

  6. Outline 11.1 Introduction 11.2 Set-Reset Latch 11.3 Gated D Latch 11.4 Edge-Triggered D Flip-Flop 11.5 S-R Flip-Flop 11.6 J-K Flip-Flop 11.7 T Flip-Flop 11.8 Flip-Flops with Additional Inputs 11.9 Summary Latches and Flip-flops

  7. Set-Reset Latch • Introduce feedback into a NOR-gate circuit • S=R=0 is a stable condition • S=1 and R=0 is a stable condition Latches and Flip-flops

  8. Set-Reset Latch Latches and Flip-flops

  9. Set-Reset Latch • This circuit is said to have memory because its output depends not only on the present inputs, but also on the past sequence of inputs. Latches and Flip-flops

  10. Set-Reset Latch • R = S = 1 is not allowed • The outputs P and Q are always complements, that is, P = Q’. • The circuit is in cross-coupled form. Latches and Flip-flops

  11. Set-Reset Latch • An input S = 1 sets the output to Q = 1 • An input R = 1 resets the output to Q = 0 • R and S cannot be 1 simultaneously Latches and Flip-flops

  12. Improper S-R Latch Operation • The latch may continue to oscillate if the gate delays are equal. Latches and Flip-flops

  13. Timing Diagram Latches and Flip-flops

  14. S-R Latch Operation Latches and Flip-flops

  15. Map and Equation of the Latch • Next-state equation, or characteristic equation • Q+ = S + R’ Q (SR=0) Latches and Flip-flops

  16. S-R Latch Applications • Components in more complex latches and flip-flops • Debouncing switching Latches and Flip-flops

  17. S-R Latch • An alternative form of the S-R latch uses NAND gates Latches and Flip-flops

  18. S-R Latch • S = 0 will set Q to 1 • R = 0 will set Q to 0 • S = R = 0 is not allowed Latches and Flip-flops

More Related