1 / 11

DCS for TRD Pre-trigger

DCS for TRD Pre-trigger. Ken Oyama Jan. 22, 2007 DCS Workshop in Heidelberg. CTP. BC+L0+L1. pre-trigger + trigger info. outside magnet. inside magnet. BPM dec. (TTCrx). control boxes. T0. FEB. BPM enc. (TTCex). TRD. V0. FEB. (anti-) coincidence. L0, L1,… + pre-trigger

melinda-crawford
Télécharger la présentation

DCS for TRD Pre-trigger

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DCS for TRD Pre-trigger Ken Oyama Jan. 22, 2007 DCS Workshop in Heidelberg

  2. CTP BC+L0+L1 pre-trigger + trigger info outside magnet inside magnet BPM dec. (TTCrx) control boxes T0 FEB BPM enc. (TTCex) TRD V0 FEB (anti-) coincidence L0, L1,… + pre-trigger + fast control TOF FPGA ACORDE CLK before after L0 L1 p-t L0 L1 Pre-trigger System Overview K. Oyama

  3. Pre-trigger System Detail K. Oyama

  4. What to be Controlled • 6 KIP DCS boards (3 for primary and 3 for backup). • 8 Wiener LV supplies. K. Oyama

  5. Power Distribution 4 crates 18 ch. (optional) • All Wiener PS, same type as for TRD but smaller current. • Special powering up methods (primary and secondary modes) are required  next slide. 4 crates 14 ch. K. Oyama

  6. Powering Up Methods (Day-I) PS Ch. [V] Purpose Normal Emergency O-08 1 -7 V0-A ON ON 2 +7 V0-A ON ON I-08 1 -7 CB-A,T0-A ON ON 2 +7 CB-A,T0-A ON ON O-29 1 -7 V0-C ON ON 2 +7 V0-C ON ON 3 -7 CB-TOF,CB-C,T0-C (primary) ON OFF 4 +7 CB-TOF,CB-C,T0-C (primary) ON OFF 5 -12 CB-TOF (primary) ON OFF 6 +12 CB-TOF (primary) ON OFF I-29 1 -12 CB-TOF (backup) OFF ON 2 +12 CB-TOF (backup) OFF ON 3 -7 CB-TOF,CB-C,T0-C (backup) OFF ON 4 +7 CB-TOF,CB-C,T0-C (backup) OFF ON Note: TRD has passive optical merger in the super-module to receive TTC (trigger and clock) via two optical fibers. If both primary and secondary system are turned on for CB-TOF, TRD will lose the TTC signal (well, will receive too many..). K. Oyama

  7. FPGAs Control through DCS (I) • Use TRD standard infrastructure (IntercomLayer, FeeServer, DIM). • Retrieve configuration data only from Database. Special “tag”? PVSS wingDB InterCom Layer command coder Configuration (cfdat) DCS board FEE Server (Control Engine) Device Drivers SCSN + JTAG K. Oyama

  8. Control through DCS (II) • Max 5 out of 6 will be powered up at the same time. • Do not configure primary and secondary system at the same time. • Downloading the configurations (numbers are max. per DCS board). • JTAG FPGA codes … 512k words. • SCSN LE-Discriminators thresholds … 44 words. • SCSN trigger elements delay setup… 44 words. • SCSN (anti-)Coincidence mode setup … 1 words. • TTC B-channel control (TTCrx-reset, sync, & etc)… several words. • Pre-trigger commands for TRD detectors (go to acq., ADC phase fixing, & etc). Synchronization with TRD configuration is necessary … 1 words. • Configuration script is given in “cfdat” structure of TRD. K. Oyama

  9. PVSS Logging • 26 temperature sensors are available in all boxes. • Live ratio and number of pre-triggers. • Health condition. K. Oyama

  10. End of Run Procedure • Readout counter values. from words • 44 detector counters CB-A/C 88 • 44 issued counters CB-A/C 88 • 44 accepted counters CB-A/C 88 • 12 trigger element counters CB-TOF 24 • 12 issued counters CB-TOF 24 • 12 accepted counters CB-TOF 24 NOTE: 44 = 12 T0 + 32 V0. 12 = 1 TRD-alive + 8 physics + 1 CB-TOF + 1 CB-A + 1 CB-C. • Reading out is done by shuttle. • Implementation will be the same as for TRD. K. Oyama

  11. Summary and Plan • Pre-trigger hardware is almost in the final shape however DCS software development just has started. • Pre-trigger system needs control of only LV and Configuration through DCS board using intercom-layer. • Pre-trigger use the same framework as TRD configuration therefore implementation will be straightforward and hopefully quick. • Needs to be finished in half year. K. Oyama

More Related