Download
1 / 3
40 likes | 61 Vues
The most common finish is Polyurethane. It comes in a few forms; interior, exterior (spar), and "poly-shades" (pre colored polyurethane). In its usual form, Polyurethane is a very hard finish that creates a shell upon that which it covers. The downside to this is that over time, the shell can develop small cracks if exposed to sunlight. The worst combination of elements for this finish is sunlight and humidity. Keeping your model in a spot out of the light will keep it looking its best.<br>A Beginning ship modeler must know that the spar Polyurethane is specific to exterior applications. It is UV resistant, but not UV proof. Although strong, if placed in direct sunlight this is a finish that will need to be recoated after a year or two. For a model, this type of Polyurethane will work just fine. Spar is classified as a "soft" finish, meaning that it moves.<br>All Polyurethane is wipe-on, and may be applied by brush, rag or spray. Spray on is good for a quick recoat, although it will take longer to build up a protective finish. The brush method gives better coverage and brush strokes will level out.<br>A Quick Drying Polyurethane is good for a quick recoat time, but will require at least three coats to get the same finish of a brushed coat of normal polyurethane.<br>For a very strong finish, try Oil such as Tung Oil, which hardens when exposed to air. The key with this oil is that before it begins to harden it soaks into wood fibers thus forming a protective finish that moves with the wood. For model ships, this is a great finish to use.<br>Wax is also an effective finish. It shows no fingerprints and can be buffed to the exact shine you want.<br>Say you are a beginning ship modeler and have modeled a ship after which you want to make some changes. You can apply paint over polyurethane without a problem. All you need to do is rough up the surface before doing so. This will allow the paint to adhere to the surface. This can be accomplished by sanding with 220 grit paper. Following these instructions should work, but are not a guarantee. It is always good to do a test patch first. Educating yourself on effective finishes will help you to get the best results possible.<br>We specialize in Wood Model Ship Kits, historic scale wooden model ship kits and model boat kits from around the world. We offer exciting model ship kits and model boat kits for the beginner as well as the advanced model ship kit builder. Visit www.historicships.com. <br>
E N D
Beginning ship modeler The most common finish is Polyurethane. It comes in a few forms; interior, exterior (spar), and "poly-shades" (pre colored polyurethane). In its usual form, Polyurethane is a very hard finish that creates a shell upon that which it covers. The downside to this is that over time, the shell can develop small cracks if exposed to sunlight. The worst combination of elements for this finish is sunlight and humidity. Keeping your model in a spot out of the light will keep it looking its best. A Beginning ship modeler must know that the spar Polyurethane is specific to exterior applications. It is UV resistant, but not UV proof. Although strong, if placed in direct sunlight this is a finish that will need to be recoated after a year or two. For a model, this type of Polyurethane will work just fine. Spar is classified as a "soft" finish, meaning that it moves.
All Polyurethane is wipe-on, and may be applied by brush, rag or spray. Spray on is good for a quick recoat, although it will take longer to build up a protective finish. The brush method gives better coverage and brush strokes will level out. A Quick Drying Polyurethane is good for a quick recoat time, but will require at least three coats to get the same finish of a brushed coat of normal polyurethane. For a very strong finish, try Oil such as Tung Oil, which hardens when exposed to air. The key with this oil is that before it begins to harden it soaks into wood fibers thus forming a protective finish that moves with the wood. For model ships, this is a great finish to use. Wax is also an effective finish. It shows no fingerprints and can be buffed to the exact shine you want.
Say you are a beginning ship modelerand have modeled a ship after which youwant to make some changes. You can apply paint over polyurethane without a problem. All you need to do is rough up the surface before doing so. This will allow the paint to adhere to the surface. This can be accomplished by sanding with 220 grit paper. Following these instructions should work, but are not a guarantee. It is always good to do a test patch first. Educating yourself on effective finishes will help you to get the best results possible. For more information: Mail id- rjeya@utsca.com, Contact Number- 866-865-7900, http://www.historicships.com/, Address- 822 N A1A Highway, Suite 310 Ponte Vedra Beach, FL 32082, USA.
