1 / 20

Electrical Safety in the Laboratory

Electrical Safety in the Laboratory. Joshua D. Horvath Andrew J. Gellman Carnegie Mellon University Department of Chemical Engineering February 18, 2003. Accidents. Electrical shock from laser power supply Electrical shock from electrophoresis power supply. Introduction.

Thomas
Télécharger la présentation

Electrical Safety in the Laboratory

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Electrical Safety in theLaboratory • Joshua D. Horvath • Andrew J. Gellman • Carnegie Mellon University • Department of Chemical Engineering • February 18, 2003

  2. Accidents • Electrical shock from laser power supply • Electrical shock from electrophoresis power supply

  3. Introduction Relationship between power, current, voltage and resistance: P = power (watts) I = current (amperes) V = voltage (volts) R = resistance (ohms) Example: Heating tape uses 5 amps at 120 volts. Power dissipated by this device is 600 watts.

  4. AC vs. DC Electricity Direct current (DC) Alternating current (AC)

  5. Electrical Components • Capacitors • Resistors • Integrated circuits

  6. Measuring Voltage Connect Probe Connect Probe + 5V -

  7. Safety Devices High Voltage Probe • Connects to normal multimeter. • Reduces voltage by factor of 1000. • Should only be used with training or assistance. • Dangerous if used improperly. You could be KILLED.

  8. Measuring Current (DC) Connect Probe Connect Probe + 5V -

  9. Safety Devices Clamp-on Ammeter • Measures AC current through a single conductor. • Does not work for DC current. • If both wires (positive and negative) pass through the clamp, no current reading is possible.

  10. Lab Equipment Power requirements (input)

  11. Lethal Electricity Chart below assumes 1 second hand to foot exposure to 120 volt, 60 cycle AC power supply. Laboratory wall outlets provide 20,000 mA !!

  12. New fuse Blown fuse Safety Devices Fuses • Protect electrical wiring from carrying too much current. • Protect malfunctioning equipment from drawing too much current. • Conductor melts if too much current flows through fuse. • Can only be used once. • Always use the correct fuse.

  13. Safety Devices Circuit Breakers • Protect electrical wiring from carrying too much current. • Mechanical switch is driven by an electromagnet. • Can only be reset many times.

  14. Safety Devices Circuit Breakers (in action)

  15. Safety Devices Circuit Breakers • How much equipment can one 20A circuit breaker handle? • Not enough to bake an entire vacuum chamber.

  16. Safety Devices Circuit Breakers • One circuit breaker may cover many electrical receptacles in a lab. • Receptacles in some labs are labeled with a number that corresponds to a circuit breaker.

  17. Preventing Accidents • Avoid contact with energized circuits. • Disconnect the power source before servicing or repairing electrical equipment. • Work with only one hand, keeping the other hand behind you or in a pocket. • If water or a chemical is spilled onto equipment, shut off power at the main switch or circuit breaker and unplug the equipment. • If an individual comes in contact with a live electrical conductor, do not touch the equipment, cord or person. • Disconnect the power source from the circuit breaker or pull out the plug using a leather belt .

  18. Preventing Accidents Extension Cords • Do not plug one extension cord into another extension cord. • Do not exceed safety ratings. • If cord is warm to touch, it is probably overloaded.

  19. Preventing Accidents Electrical Fires • Unplug equipment first. • Use dry chemical fire extinguisher. • If fire is large, unplug equipment and call fire dept. • Never use water!!

  20. Conclusions • Be careful with electricity. • Ask someone for help if you are unsure.

More Related