1 / 25

A 2.5V, 77-GHz, Automotive Radar Chipset

WE2B-5. A 2.5V, 77-GHz, Automotive Radar Chipset. Sean T. Nicolson 1 , Keith A. Tang 1 , Kenneth H.K. Yau 1 , Pascal Chevalier 2 , Bernard Sautreuil 2 , and Sorin P. Voinigescu 1

abba
Télécharger la présentation

A 2.5V, 77-GHz, Automotive Radar Chipset

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. WE2B-5 A 2.5V, 77-GHz, AutomotiveRadar Chipset Sean T. Nicolson1, Keith A. Tang1, Kenneth H.K. Yau1, Pascal Chevalier2, Bernard Sautreuil2, and Sorin P. Voinigescu1 1) Edward S. Rogers, Sr. Dept. of Electrical & Comp. Eng., University of Toronto, Toronto, ON M5S 3G4, Canada 2) STMicroelectronics, 850 rue Jean Monnet, F-38926Crolles, France

  2. Outline • Motivation • Transceiver architecture • Circuit design & layout + some device insight • Fabrication technology • Measurements • Conclusions

  3. Applications • W-band applications: 77GHz auto radar, 94GHz weather radar, imaging, data communications • All applications require a W-band radio transceiver.

  4. The Doppler Radar Transceiver Modulation • Doppler transceiver block diagram • Development steps • Design & test circuit blocks + optimize HBT for circuit performance • Integrate circuit blocks into transceiver • Duplicate to form arrays VCO freq. div. PA To PLL Antennae IF amp LNA Mixer

  5. Low-noise Amplifier 250mm • 3-stage design, add R1 to de-Q the final stage. • Noise & impedance matching including CPAD [Nicolson, 2006]. 1pF decoupling caps

  6. Power Amplifier • Primary goal: maximize PAE • common source, class AB operation

  7. Down-conversion Mixer • Classical Gilbert cell mixer has poorlinearity at 2.5V • Eliminate RF pair • Couple to LNA using transformer • Bias quad from center tap • Simulations • 9dB conversion gain • +3dBm OP1dB (1.25VPP/side) • 12.5mW PDC input

  8. Mixer + IF Amp Layout • Layout is critical at 77GHz.

  9. Frequency Divider • The most challenging block to operate from 2.5V. • Given sizes of Q1-Q6, the size of Q7 & Q8 can be optimized. • important: inductor size, swing, latch pair size, current density.

  10. Frequency Divider • The most challenging block to operate from 2.5V. • Given sizes of Q1-Q6, the size of Q7 & Q8 can be optimized. • important: inductor size, swing, latch pair size, current density.

  11. SiGe Technology [Chevalier, 2006] • 230/290GHz fT/fMAX SiGe HBT process • Several “process splits” to find optimal HBT profile. 14mA/mm2

  12. LNA Measurements • Fabricated & measured a 65nm CMOS LNA for comparison. • CMOS has more power supply variation (HBT feedback is stronger) • CMOS has low output resistance  higher bandwidth

  13. LNA Measurements • S21 vs. temp. shows 6dB variation up to 125C @ center band. • Again, upper band shows greater variation (less feedback). smaller change in gain here larger change in gain here

  14. PA Measurements • PAE = 15.7%, PSAT = +14 dBm, OP1dB = +11dBm

  15. Mixer + IF Amplifier Measurements • DSB noise figure of 13dB is pessimistic • harmonics from LO multiplier source, includes 3dB transformer loss. • Min. NF current density at 73GHz (common base) is 5.5mA/mm2.

  16. Frequency Divider Measurements • Operates up to 105.44GHz at 25°C and 97GHz at 100°C. • limited by power available from source.

  17. Performance of Process Splits • The best split is the reference, with the highest fMAX.

  18. Conclusions and Future Work • Excellent performance despite 2.5V supply. • SiGe divider 94GHz self-oscillation, and 75mW power consumption. • 77GHz power amplifier PAE of 15.7% • +5dBm OP1dB from Mixer + IF amplifier • -101.5dBc/Hz at phase noise at 1MHz offset • Transceiver currently in the fab • < 500mW power consumption (180mW for receiver, inc. VCO) • Contains only 33 HBTs (includes 16 in divider) + 2 MOS varactors.

  19. Acknowledgements • Ricardo Aroca and KatiaLaskin for measurement help • JaroPristupa and Eugenia Distefano for CAD/Network support • STMicroelectronics & CITO for fabrication and funding

  20. **Voltage-Controlled Oscillator • Minimize phase noise, supply & temp dependence [2], [3]. • Small LB, differential tuning • C1 + CBE >> CVAR, C3 cancels CBC

  21. VCO Measurements • Phase noise better than -100dBc/Hz at 77GHz [2], [3].

  22. More About Process Splits • LNA S21 for several process splits. • Reference split looks the best.

  23. More About Process Splits • PA saturated S21 for several process splits • Again, the reference split looks the best.

  24. More About Process Splits • PA S11 for several process splits

  25. Inductor Measurements • Accurately simulated/modeled [Dickson, 2005] passives ( ±1pH).

More Related